Electro discharge machining

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/10

encourage image

There's no tags or description

Looks like no tags are added yet.

11 Terms

1
New cards
<p>What is electro discharge machining (EDM) and how does it work?</p>

What is electro discharge machining (EDM) and how does it work?

EDM is an advanced machining technologies that focuses on the subtraction of material to create a final shape

It works when two electrodes the tool and workpiece are placed into a dielectric fluid and submitted to high voltage and separated by a gap. The tool is then moved toward the workpiece and if the gap is small enough an electrical current occurs by the discharge of the capacitor which creates a spark which in turn creates a crater on the workpiece and on the tool. Dielectric is contaminated with debris and so the tool is moved away so the dielectric can be cleaned.

<p>EDM is an advanced machining technologies that focuses on the subtraction of material to create a final shape</p><p>It works when two electrodes the tool and workpiece are placed into a dielectric fluid and submitted to high voltage and separated by a gap. The tool is then moved toward the workpiece and if the gap is small enough an electrical current occurs by the discharge of the capacitor which creates a spark which in turn creates a crater on the workpiece and on the tool. Dielectric is contaminated with debris and so the tool is moved away so the dielectric can be cleaned. </p>
2
New cards

the trade off between efficiency vs quality

Energy output is controlled by the voltage, current and time on/off to charge/ discharge the capacitor

Higher energy creates:

  • bigger craters

  • bigger spark gap between the electrodes and machined surface

  • higher removal rate

  • rougher surface (higher Ra)


what is Ra?

It is used to measure roughness and takes into account the average displacement of peak and trough of the craters, the higher the Ra the more rough. Can have a near mirror finish at 0.02 micrometres or a rough surface at 10 micrometres


3
New cards

What are the 4 typical uses (processes) of electro discharge machining?

  • Wire EDM

  • Die sinking EDM

  • EDM drilling

  • EDM milling


4
New cards
<p>What is die sinking EDM</p>

What is die sinking EDM

A tool mainly made out of graphite or copper, tungsten or tungsten carbide moved in the Z axis (up and down) and acts like a punch to create a negative version on the workpiece.

to produce a part of good quality in a short period the roughing, finishing method is used whereby high energy is used to remove a load of material at first leaving some material left over so it can be removed by the lower energy finishing to create a smooth surface. As the spark gap is smaller at lower energies the tool needs to be bigger (not always possible as it depends on the shape) or the tool needs to be moved around in the shape of the component.


advantages

  • high quality surfaces

  • any conductive material, regardless of hardness

limitations

  • tools can be difficult to produce

  • tools can be difficult to control in small geometries

  • slow process and is expensive

  • tool also wears out as well from sparks


<p>A tool mainly made out of graphite or copper, tungsten or tungsten carbide moved in the Z axis (up and down) and acts like a punch to create a negative version on the workpiece.</p><p>to produce a part of good quality in a short period the roughing, finishing method is used whereby high energy is used to remove a load of material at first leaving some material left over so it can be removed by the lower energy finishing to create a smooth surface. As the spark gap is smaller at lower energies the tool needs to be bigger (not always possible as it depends on the shape) or the tool needs to be moved around in the shape of the component. </p><p></p><p>advantages</p><ul><li><p>high quality surfaces</p></li><li><p>any conductive material, regardless of hardness</p></li></ul><p>limitations </p><ul><li><p>tools can be difficult to produce</p></li><li><p>tools can be difficult to control in small geometries</p></li><li><p>slow process and is expensive </p></li><li><p>tool also wears out as well from sparks </p></li></ul><p></p>
5
New cards

How to control die electric flushing on die sinking?

knowt flashcard image
6
New cards

Wire electro discharge machining

wire is fed into workpiece and the sparks cut though the workpiece by electrical discharges between the wire and workpiece. The wire is on a supply and take up wheel so new wire is fed though and therefore does not wear out and snap.

advantages

  • no wear compensation needed as wire is constantly renewed

  • easy flushing bought by movement of wire

  • high quality surfaces

  • any conductive material regardless of hardness


main limitation

  • wire control as its in tension

  • can only machine conductive materials

  • produces mainly 2D shapes

  • corner diameters limited by wire diameter + spark gap


uses: gears, fly fishing lines

7
New cards

Think about the wire EDM strategy used for producing a die

knowt flashcard image
8
New cards

Think about the wire EDM strategy used for producing a punch

knowt flashcard image
9
New cards

EDM drilling

Can produce very deep holes of an aspect ratio over 100 meaning the length of the rod can be over 100 times the diameter. regular drilling cannot do this due to poor thermal removal and lesser material removal.


material is flushed though hollow electrode

<p>Can produce very deep holes of an aspect ratio over 100 meaning the length of the rod can be over 100 times the diameter. regular drilling cannot do this due to poor thermal removal and lesser material removal. </p><p></p><p>material is flushed though hollow electrode </p>
10
New cards

EDM milling

like drilling a small rotating cylindrical electrode is used but with a cutting strategy similar to standard milling and can produce complex 3D shapes with features down to 5 micrometres

It has good flushing leading to improved geometry but is extremely time consuming and typically only used for cavities smaller than 100mm²

11
New cards

Material removal rate table example

knowt flashcard image