1/163
Comprehensive practice flashcards covering error detection, error correction, UART and USRT architecture, digital transmission, modulation techniques, and pulse code modulation.
Data Communication Error
A condition occurring during transmission when the receiver's information does not match the sender's information, caused by noise that alters binary bits.

Single Bit Error
A type of transmission error where only one bit in a given data string is corrupted.

Multiple Bit Error
A type of transmission error where two or more non-consecutive bits within a given data string are corrupted.

Burst Error
A type of transmission error where two or more consecutive bits within a data string are corrupted.
Line Outages
A source of error caused by storms or accidents.
White Noise
An error source caused by the random thermal movement of electrons, prevented by increasing signal strength.
Impulse Noise
An error source caused by a sudden surge in electricity (such as lightning), prevented by shielding or moving wires.
Cross-talk
An impairment caused when multiplexer guardbands are too small or wires are placed too close together, prevented by increasing guardbands or shielding/moving wires.
Echo
A transmission impairment caused by poor line connections, prevented by fixing connections or tuning equipment.
Attenuation
The gradual decrease in signal magnitude over distance, prevented by installing repeaters or amplifiers.
Intermodulation Noise
Noise produced when signals from several circuits combine, prevented by moving or shielding wires.
Jitter
An error condition caused when analog signals unexpectedly change phase, prevented by tuning equipment.
Harmonic Distortion
An impairment caused when an amplifier changes phase, prevented by tuning equipment.
Probability of Error (Pe)
The theoretical expected error rate of a system (for example, Pe=10−4 indicates 1 bit is expected to be in error out of every 10,000 bits transmitted).
Bit Error Rate (BER)
The empirical, actual measured error performance of a transmission system, typically compared against the theoretical probability of error.
Lost Message
An error message condition where the data either never arrives at the destination or arrives so severely corrupted that it is completely unrecognizable.
Damaged Message
An error message condition where the transmission arrives and is recognized at the destination, but contains one or more bit errors.
Error-Detecting Codes
Transmitted codes that append redundant information to enable the receiver to determine whether transmission errors occurred.
Error-Correcting Codes
Transmitted codes containing sufficient extraneous information to enable the receiver to detect an error and identify which specific bit or bits failed.
Character Redundancy
An error-detection technique where each single character data unit is sent multiple times, usually twice, so the receiver can compare them.
Message Redundancy
An error-detection scheme where an entire message is transmitted multiple times for receiver comparison.
Echoplex
An interactive error-detection technique where received data is retransmitted back to the sending terminal and displayed on screen for operator verification.
Exact-Count Coding
An error-detection coding scheme where the number of binary 1s and binary 0s in every valid character remains constant.
Vertical Redundancy Check (VRC)
The simplest error-detection scheme (also called character parity), which appends an odd or even parity bit to each individual character.
Longitudinal Redundancy Check (LRC)
An error-detection method (also called message parity) where a parity bit is calculated across each bit position of a block and transmitted as a block check character.
Checksum
A redundancy checking technique where data words are summed together at the transmitter to produce an error-checking character appended to the end of the message.
Check Character Checksum
A checksum method where a decimal value is assigned to each character and added together to produce a check digit (such as in POSTNET bar codes).
Single Precision Checksum
A checksum calculation where binary addition is performed on data words and any resulting carryout bit is discarded.
Double Precision Checksum
A checksum method where the checksum character is twice as long as the character length, allowing carryouts to be retained.
Honeywell Checksum
A double precision checksum technique based on interleaving consecutive data words to form double-length words.
Residue Checksum
A checksum method where binary addition is performed and any carryout bit is added directly into the least significant bit (LSB) of the sum.
Cyclic Redundancy Check (CRC)
A highly reliable polynomial-based error-detection technique where data is divided by a generator polynomial and the remainder is appended as a block check character.
CRC Modulo-2 Division
A binary division process executed without carries or borrows, in which the remainder is generated using successive XOR operations.
CRC Generator Polynomial (P(x))
A predetermined prime polynomial divisor whose highest power corresponds to the number of bits in the appended CRC block check character.
CRC-16
A 16-bit redundancy code standard defined by the generator polynomial X16+X15+X2+X0, used for 8-bit codes such as ASCII and EBCDIC.
CRC-32
A 32-bit cyclic redundancy check code standard commonly utilized in Ethernet local area networks.
Symbol Substitution
An error correction method designed for human terminal operators to inspect received data and manually replace characters or request retransmission.
Automatic Retransmission Request (ARQ)
An error correction technique where the receiving terminal automatically requests the retransmission of data detected to contain errors.
Discrete ARQ
An ARQ method where the receiver returns an ACK for error-free messages or a NAK for corrupted messages, prompting retransmission after a timeout.
Continuous ARQ (Selective Repeat)
An ARQ scheme where sequentially numbered message blocks are sent continuously, allowing the receiver to asynchronously request retransmission of specific failed blocks.
Forward Error Correction (FEC)
The only error-correction scheme that detects and automatically corrects transmission errors at the receiver without requesting a retransmission.
Hamming Code
A popular forward error correction code that corrects single-bit errors in synchronous data streams by positioning parity bits at powers-of-two bit locations.
Hamming Bit Formula
The mathematical inequality 2n≥m+n+1 used to determine the minimum number of Hamming bits (n) required for a character with m data bits.
Syndrome
The decimal value derived by summing the bit positions of failed parity checks in a Hamming code, which directly pinpoints the erroneous bit.
Universal Asynchronous Receiver Transmitter (UART)
An integrated circuit hardware device that translates data between parallel and serial formats for asynchronous data communications.
UART Shift Register
The internal sequential logic circuit inside a UART that carries out the fundamental conversion between serial and parallel data forms.
Parallel Data Bus (UART)
The direct parallel link connecting the CPU to the UART that enables data transfers at CPU clock speed.
Address Decoder (UART)
The functional circuit block in a UART interface that handles addressing into the internal UART registers from the CPU address bus.
Transmit Buffer Empty (TBMT)
A UART status signal informing the CPU that the transmit buffer register is vacant and ready to accept new data.
RS-232 Signal Converter
A level-shifting circuit that converts TTL signals from the UART into RS-232 voltage levels (−3V to −25V for logic 1, and +3V to +25V for logic 0).
Mode Instruction Word (Control Word)
An instruction word stored in the UART control register specifying parameters such as data bit length, parity enable/type, and clock baud factor.
Full ASCII
An asynchronous character transmission format with a maximum length of 11 bits, consisting of 7 or 8 data bits combined with start, stop, and parity overhead bits.
Control Register (UART)
An internal UART register dedicated to storing the control word and operational configuration settings.
Data, Parity, and Stop Bit Logic
A transmitter circuit block in a UART that generates and appends the programmed parity and stop bits to outgoing character data.
Status Word Register (UART)
An n-bit internal register monitoring buffer states and error conditions including TBMT, RPE, RFE, RDA, and ROE.
Transmit Buffer Register
A temporary storage register inside a UART that holds parallel data from the CPU before it is transferred into the transmit shift register.
Transmit Shift Register
The parallel-in, serial-out register in a UART transmitter that serializes data and shifts it onto the serial output line.
Transmit Shift Register Empty Logic Circuit
A monitoring circuit in the UART transmitter that determines when character shifting out of the transmit shift register has completed.
Transmit Data Strobe (TDS)
A control strobe signal pulsed by the CPU to load parallel data into the UART transmit buffer register.
Transmit End of Character (TEOC)
An active signal within the UART transmitter indicating that the current serialized character has ended, prompting parallel loading of the next character.
Start Bit Verification Circuit
A receiver circuit that validates incoming start bits by detecting 1-to-0 transitions and sampling logic 0 to establish timing references at the center of bits.
Receive Shift Register
The serial-in, parallel-out register in the UART receiver that clocks in incoming serial data bits following start-bit validation.
Receive Buffer Register
A holding register in the UART receiver that receives parallel characters from the shift register for subsequent CPU retrieval.
Receive Data Available (RDA)
A status flag asserted in the status word register when a completed character has been moved into the receive buffer register.
Status Word Enable (SWE)
A control line pulsed by the CPU to read the current contents of the UART status word register.
Receive Data Enable (RDE)
A control pulse activated by the CPU to read parallel character data from the receive buffer register.
Receive Data Available Reset (RDAR)
A reset signal issued by the CPU after reading the receive buffer to clear the active RDA flag.
Receive Parity Error (RPE)
A status flag indicating that received character data failed the internal parity check.
Receive Framing Error (RFE)
A status flag asserted when the receiver fails to locate a valid stop bit at the expected character boundary.
Receive Overrun Error (ROE)
An error condition triggered when an unread character in the receive buffer is overwritten by a newly arrived character due to inadequate flow control.
Sampling Error (UART)
The time difference between when an incoming serial bit sample is taken and the actual center of that data bit.
Detection Error (UART)
The time delay occurring between the initial beginning of a start bit and the instant it is detected by the receiver.
Maximum Detection Error (MDE)
The maximum possible delay in detecting a start bit, equivalent to the time period of one receive clock cycle (1/Rcl).
Universal Synchronous Receiver Transmitter (USRT)
An integrated circuit designed for synchronous data communications that performs parallel-to-serial conversion, parity checking, and SYNC character handling.
SYNC Character
A unique synchronization bit pattern inserted into synchronous transmissions to establish bit and character alignment between transmitter and receiver.
Transmit Sync Strobe (TSS)
A strobe line pulsed by the CPU to load a synchronization character into the USRT Transmit Sync Register.
Sync Character Transmit (SCT)
A status signal asserted by a USRT to inform the CPU that a synchronization character has been transmitted.
Receive Sync Strobe (RSS)
A strobe line pulsed by the CPU to load the expected synchronization character into the USRT Receive Sync Register.
Receive Rest (RR)
A control line pulsed by the CPU to place the USRT receiver into search mode to locate incoming SYNC characters.
Sync Character Receive (SCR)
A signal output by the USRT indicating that an incoming character matching the contents of the Receive Sync Register has been detected.
Digital Communications
The transmittal of digitally modulated analog carriers between two or more points via wireless media or wired physical channels.
Digital Transmission
The transmittal of discrete digital pulses directly between two or more points across a physical communications facility.
Time-Division Multiplexing (TDM)
A digital processing technique that interleaves multiple digital signals into unique time slots across a single transmission medium.
Modulation
The process of varying properties of a high-frequency carrier signal in accordance with an information-bearing modulating signal.
Analog Modulation
A modulation scheme where both the high-frequency carrier wave and the modulating message signal are continuous analog signals.
Digital Modulation
A modulation scheme where an analog carrier wave is varied in accordance with discrete, digital input information, commonly implemented by modems.
Minimum Nyquist Bandwidth
The theoretical minimum channel bandwidth required to propagate digital signals without intersymbol interference, equal to fb/2 for two-level systems.
Multilevel Signaling
A signaling technique using M distinct coding levels to encode N=log2(M) bits per symbol, allowing the transmission bit rate to exceed twice the bandwidth.
Baud Rate
The rate of signal or symbol transitions per second across a communications medium, calculated as Baud=fb/N.
Amplitude Shift Keying (ASK)
A digital modulation method where the amplitude of an analog carrier shifts between discrete levels in proportion to binary modulating data.
On-Off Keying (OOK)
A simple form of ASK where the output wave is switched between zero volts (off) for logic 0 and full carrier amplitude (on) for logic 1.
Normalized Binary Waveform
A standardized binary representation used in modulation equations where logic 1 corresponds to +1V and logic 0 corresponds to −1V.
Frequency Shift Keying (FSK)
A digital angle modulation scheme where the frequency of a constant-amplitude carrier shifts between discrete frequencies based on binary input data.
Mark Frequency (fm)
The carrier frequency assigned to represent a binary logic 1 in an FSK system.
Space Frequency (fs)
The carrier frequency assigned to represent a binary logic 0 in an FSK system.
Rest Frequency (FSK)
The unmodulated carrier center frequency of an FSK system, situated halfway between the mark and space frequencies.
Peak Frequency Deviation (Δf)
The maximum difference between the unmodulated rest frequency and either the mark or space frequency, calculated as Δf=∣fm−fs∣/2.
FSK Modulation Index (MI)
A unitless index defined as the ratio of peak frequency deviation to modulating frequency, expressed as MI=Δf/fa=∣fm−fs∣/fb.
FSK Bandwidth Equation
The formula used to compute the minimum required Nyquist bandwidth for an FSK signal: B=2(Δf+fb).
Phase-Locked Loop (PLL) Demodulator
The most common circuit configuration used to demodulate and recover binary data from an incoming analog FSK signal.