1/59
Looks like no tags are added yet.
Main bearing oil seals used with turbine engines are usually what types?
A. Teflon and synthetic rubber seals
B. Labyrinth and carbon rubbing seals
C. Labyrinth and silicone rubber seals
D. Profile and dovetail seals
B. Labyrinth and carbon rubbing seals
Name three types of combustion chambers used on turbine engines.
Multiple-can
Can-annular
Annular
An advantage of the centrifugal-flow compressor is its high
A. Ram efficiency
B. Peak efficiency
C. Pressure rise per stage
D. Weight per stage
C. Pressure rise per stage

Identify the hot section.
The combustion and turbine area toward the rear of the engine.


Identify the turbine section.
The turbine blade assembly immediately behind the combustion chambers.

List the three methods of attaching (not locking) compressor blades to a compressor disc.
Fir-tree
Bulb
Dovetail
Three types of turbine blades are
A. Reaction, converging, and diverging
B. Impulse, reaction, and impulse-reaction
C. Impulse, vector, and impulse-vector
D. Labyrinth, gauss, and compensated
B. Impulse, reaction, and impulse-reaction
What are the two (2) different types of turbine engine compressors?
Centrifugal-flow compressor
Axial-flow compressor
What is the primary factor that controls the pressure ratio of an axial flow turbine engine?
A. Diameter of the engine inlet
B. Compressor inlet temperature
C. Ram air pressure
D. The number of stages in the compressor
D. The number of stages in the compressor

Identify the point of the highest pressure in the engine.
At the compressor discharge/diffuser, just before the combustion chamber.

The compressor stators in a gas turbine engine act as diffusers to
A. decrease the velocity of the gas flow.
B. increase the velocity and decrease the pressure of the gas.
C. increase the velocity of the gas flow.
D. increase the velocity of the fuel flow.
A. decrease the velocity of the gas flow.
A turbine engine compressor which contains vanes on both sides of an impeller is a?
A. Double entry centrifugal compressor
B. Double entry axial-flow compressor
C. Single entry centrifugal compressor
D. Single entry axial-flow compressor
A. Double entry centrifugal compressor
List the four (4) most common types of gas turbine engines.
Turbojet
Turbofan
Turboprop
Turboshaft
The primary purpose of the turbine section in a turbojet engine is to?
A. Increase exhaust velocity to generate more thrust
B. Convert exhaust pressure into gas velocity
C. Drive the compressor section of the engine
D. Straighten exhaust gases and reduce turbulence
C. Drive the compressor section of the engine
What is a Blisk?
The blade and disk combined into one assembly.
The purpose of an exhaust cone on a turbojet engine is to?
A. Collect the exhaust gases and act as a noise suppressor
B. Swirl and collect the exhaust gases into a single exhaust jet
C. Straighten and collect the exhaust gases into a single jet
D. Prevents exhaust gases from contacting the aircraft structure
C. Straighten and collect the exhaust gases into a single jet
Name the two turbine engine components that can be used to help control compressor stalls.
Variable Stator Vanes and Bleeder Valves
Which turbine engine compressor offers the greatest advantages for both starting flexibility and improved high altitude performance?
A. Single stage centrifugal flow
B. Dual stage centrifugal flow
C. Dual spool axial flow
D. Single spool axial flow
C. Dual spool axial flow
What are the two basic elements in the turbine section of a turbine engine?
A. Impeller and diffuser
B. Hot section and cold section
C. Burner can and diffuser
D. Stator and rotor
D. Stator and rotor
One function of the turbine nozzle guide vane in a turbine engine is to?
A. Decrease the velocity of the exhaust gases
B. Center the fuel spray in the combustion chamber
C. Direct cooling air around the base of the turbine blades
D. Direct exhaust gases to strike the turbine blades at the desired angle
D. Direct exhaust gases to strike the turbine blades at the desired angle

Identify the combustion chamber section.
The combustion chamber section where fuel mixes with compressed air and burns.


Identify the Compressor section.
The bladed section at the front of the engine that compresses incoming air.


Identify the point of highest temperature in the engine.
At the turbine inlet, immediately after the combustion chamber.

What part of a turbine engine reduces the velocity of compressor air while at the same time increases its pressure to its highest value in the engine?
A. Stator Vane
B. Diffuser
C. Burner can
D. Air bleed valve
B. Diffuser
List five (5) of the basic sections to a turbine engine.
Inlet
Compressor
Combustion
Turbine
Exhaust
In which type of turbine engine combustor is the burner case and liner removed and installed as one unit during routine maintenance?
A. Multiple can
B. Can annular
C. Annular
D. Reverse flow annular
A. Multiple can
In a two spool turbo jet engine the high pressure turbine drives the?
A. N1 compressor
B. N2 compressor
C. Both the N1 and N2 compressors
D. The accessory section only
B. N2 compressor
What is another name for the constant pressure cycle? This cycle is used to describe the combustion events that occur in a turbine engine.
A. The Otto cycle
B. The Brayton Cycle
C. The Moss Cycle
D. The Whittle Cycle
B. The Brayton Cycle
What is the purpose of the shrouds on the turbine blades of an axial flow turbine engine?
A. Reduce vibration
B. Increase blade tip speed
C. Prevent cooling air from entering the exhaust stream
D. Prevent turbine stall
A. Reduce vibration

Identify the cold section.
The inlet and compressor area, including the diffuser.
What compression ratio is a single stage of a centrifugal flow compressor capable of supplying?
A. 1.25 to 1
B. 5 to 1
C. 10.5 to 1
D. 15 to 1
D. 15 to 1
What compression ratio is a single stage of a typical axial flow compressor capable of supplying?
A. 1.25 to 1
B. 5 to 1
C. 10.5 to 1
D. 15 to 1
A. 1.25 to 1
What type of sensor is an EGT sensor?
A. Resistance bulb
B. Thermo switch
C. Autosyn syncro
D. Thermocouple
D. Thermocouple
When starting a turbine engine a hung start could occur. Which statement below is a description of a hung start?
A. Exhaust temperature exceeds specified limits
B. Engine ignites but fails to reach idle RPM
C. RPM exceeds engine operating limits
D. Engine reaches maximum starter speed but fails to ignite
B. Engine ignites but fails to reach idle RPM
Turbine engine components that are exposed to high temperatures generally may not be marked with (select the letter next to the combination of numbers that all apply)
Layout dye
Commercial felt tipped marker
Wax or grease pencil
Chalk
Graphite lead pencil
A. 1, 2, and 3
B. 2 and 3
C. 3 and 5
D. 4 and 5
C. 3 and 5
Wax or grease pencil
Graphite lead pencil
After a compressor wash how is the interior of the engine dried out?
A. Engine must remain static for a period of time depending on the size of the engine
B. High volume air is blown into the engine inlet
C. The engine is bagged and heated to evaporate fluid residue
D. The engine is run for a period of time
D. The engine is run for a period of time
What is the first engine instrument indication of a successful start of a turbine engine?
A. A rise in oil pressure.
B. A rise in the exhaust gas temperature.
C. A rise in the engine fuel flow.
B. A rise in the exhaust gas temperature.
When starting a turbine engine and a hot start occurs what two things should you do?
Shut off the fuel.
Continue motoring the engine with the starter.
If during an inspection at engine overhaul, ball or roller bearings are found to be in good condition but are magnetized, they
A. Must be anodized before use
B. Cannot be used again
C. Are in an acceptable service condition
D. Must be degaussed before use
D. Must be degaussed before use
What types of bearings are considered Anti Friction Bearings and are used on the main shaft of a turbine engine?
A. Ball and roller bearings
B. Plain and sintered bearings
C. Fluid and tapered bearings
D. Needle and spherical bearings
A. Ball and roller bearings
What material is sprayed in to a turbine engine during a desalinization wash?
A. Walnut shells
B. An emulsion type cleaner
C. Demineralized water
D. Carboblast
C. Demineralized water
Some high-volume turboprop and turbojet engines are equipped with two spool or split compressors. When these engines are operated at high altitudes, the
A. throttle must be retarded to prevent over speeding of the high-pressure rotor due to the lower density air.
B. low pressure rotor will increase in speed as the compressor load decreases in the lower density air.
C. low pressure rotor will decrease in speed as the compressor load decreases in the lower density air.
D. The mixture must be adjusted to compensate for the less dense air.
B. low pressure rotor will increase in speed as the compressor load decreases in the lower density air.
When starting a turbine engine, a hung start is indicated if the engine
A. fails to reach idle RPM.
B. exhaust gas temperature exceeds specified limits.
C. RPM exceeds specified operating speed.
A. fails to reach idle RPM.
When the leading edges of first stage turbine blades are found to have stress rupture cracks which of the following are suspected?
A. Faulty cooling shield
B. Over temperature condition
C. Over speed condition
D. Engine stall
B. Over temperature condition
The blending of blades and vanes in a turbine engine...
A. is usually only accomplished at engine overhaul
B. should be performed parallel to the length of the blade
C. only vanes may be blended, blades should never be blended.
D. should never be accomplished, once the blade is damaged a safe level of strength cannot be determined
B. should be performed parallel to the length of the blade
What is the primary limiting factor in turbine engine operation?
Turbine gas temperature (TIT or EGT).
What is the proper starting sequence for a turbine engine?
Starter → Ignition → Fuel
What is one of the first indications that a fuel nozzle in the combustion section is plugged?
A. Excessive EGT
B. Lower fuel flow to the engine
C. Hot spots or streaking on the tail cone
D. Smoke in the turbine engine exhaust
C. Hot spots or streaking on the tail cone
What are three indications you should see before you add fuel when starting a PT6 turboprop engine?
Oil pressure
N1 rotation
N2 max motoring
Which of the following engine variables is the most critical during turbine engine operation?
A. Compressor inlet temperature
B. Compressor RPM
C. Fuel flow
D. Turbine inlet temperature
D. Turbine inlet temperature
Turbine engines can be maintained in basic sections, what are the two basic sections that turbine engines are divided into when determining inspection and overhaul schedules?
A. Impeller and diffuser
B. Hot and Cold
C. Stator and rotor
D. Cold stream and engine core
B. Hot and Cold
When should the turbine engine starter be disengaged?
When the engine reaches self-accelerating speed.
What are the two most common types of bearing seals used on turbine engines?
Carbon seals
Labyrinth seals
A cool-off period prior to shutdown of a turbine engine is accomplished in order to
A. prevent vapor lock in the fuel control and/or fuel lines.
B. allow the turbine wheel to cool before the case contracts around it.
C. prevent seizure of the engine bearings.
B. allow the turbine wheel to cool before the case contracts around it.
What two sensor inputs are used to calculate EPR?
A. Engine inlet pressure and burner can pressure
B. Engine inlet pressure and turbine discharge pressure
C. Engine inlet temperature and turbine inlet temperature
D. Compressor discharge pressure and turbine discharge pressure
B. Engine inlet pressure and turbine discharge pressure
What should be done initially if a turbine engine catches fire when starting?
A. Continue starting attempt in order to blow out the fire.
B. Turn off the fuel and continue engine rotation with the starter.
C. Continue engine start rotation and discharge a fire extinguisher into the intake.
B. Turn off the fuel and continue engine rotation with the starter.
What is the term used to describe the lengthening of turbine blades due to centrifugal force and heat?
A. Shingling
B. Galling
C. Distortion twist
D. Creep
D. Creep
When turbine engine blades are removed for lubrication or for a detailed inspection they must be reinstalled in:
A. A position 180deg away
B. A position 90 deg from the original position
C. In the same slot they were removed from
D. A position 120 deg from the original position
C. In the same slot they were removed from
The recurrent ingestion of dust or other fine airborne particulates into a turbine engine can result in
A. foreign object damage to the compressor section.
B. the need for less frequent abrasive grit cleaning of the engine.
C. erosion damage to the compressor and turbine sections.
C. erosion damage to the compressor and turbine sections.
When does a turbine engine reach its hottest temperature?
At engine start.