1/54
Looks like no tags are added yet.
Which type of pump is commonly used for viscous fluids like oil?
Screw pump
Which parameter represents the energy required at pump suction to avoid cavitation?
NPSH
Which type of pump is classified as a positive displacement pump?
Reciprocating pump
Which is the point where pump curve and system curve intersect?
Operating point
Which type of pump is commonly used for boiler feed applications?
Multistage centrifugal pump
Which pump type uses a flexible tube squeezed by rollers?
Peristaltic pump
Which code specifies centrifugal pump standards for petroleum industries?
API 610
What happens to volume flow rate as head increases in a pump curve?
Decreases
What happens to pump power when speed is doubled?
Becomes eight times
What determines the motor power required for a pump?
Head and efficiency
Which type of seal is most reliable for high-pressure pumps?
Mechanical seal
The efficiency of a fan is defined as:
η = Output air power / Input shaft power
What fan type is best for handling large volumes of clean air at low pressure?
Propeller fan
Which blower type creates vacuum as well as pressure applications?
Regenerative blower
Which instrument is commonly used to measure airflow in ducts?
Pitot tube
Which is a common method of fan speed control?
Variable frequency drive
Which type of fan impeller is most prone to erosion in dusty conditions?
Forward-curved blades
Which is a common standard for testing fan performance?
AMCA Standard 210
Which application requires high-pressure blowers?
Pneumatic conveying
Which type of fan is best suited for medium pressure and medium volume?
Backward-curved centrifugal fan
Which fan type is characterized by low efficiency but compact design?
Forward-curved centrifugal fan
Which compressor type is best for transporting natural gas in pipelines?
Centrifugal compressor
Which standard covers centrifugal compressors for petroleum and gas industries?
API 617
Which standard covers performance testing of compressors?
ASME PTC 10
Which problem occurs when compressor flow drops below surge limit?
Surge
Which part of centrifugal compressor imparts kinetic energy to gas?
Impeller
Which failure occurs due to liquid entering compressor cylinders?
Liquid slugging
What compressor is suitable for large office towers that require reliability and low maintenance?
Single stage centrifugal compressor with gear drive
What causes choking in a compressor?
Flow reaching sonic velocity
What is the optimal intercooler pressure for a two-stage compressor?
Geometric mean pressure
Which term describes the temperature difference between hot water entering and cold water leaving the tower?
Cooling range
Cooling tower effectiveness is defined as:
(Range / (Range + Approach)) × 100%
What is the limiting temperature in cooling tower analysis?
WBT
Which material is commonly used for cooling tower fill?
PVC
Which problem occurs due to microbial contamination in cooling towers?
Legionella growth
Which cooling tower problem causes uneven water distribution?
Nozzle clogging
Which type of cooling tower is least affected by wind direction?
Induced draft tower
Which parameter is minimized in efficient cooling towers?
Approach temperature
What heat exchanger type has concentric tubes, one fluid inside and one outside?
Double-pipe heat exchanger
Which dimensionless number represents heat exchanger effectiveness?
NTU (Number of Transfer Units)
Which code provides standards for shell-and-tube heat exchangers?
TEMA
Which heat exchanger type is best for compact, high-efficiency service?
Plate heat exchanger
What type of reboiler is commonly used in distillation columns?
Kettle reboiler
Which parameter is reduced by using baffled shell-and-tube exchangers?
Dead zones
Which type of exchanger is best for heat recovery from exhaust gases?
Economizer
What determines the capacity of a conveyor?
Area, velocity, and density
Which type of conveyor is used for vertical lifting of bulk solids?
Bucket elevator
Which type of conveyor uses a rotating helical blade inside a tube?
Screw conveyor
What is the purpose of a snub pulley?
Increase belt wrap angle
Which crane is mounted on a wall or column?
Jib crane
Which type of conveyor is most energy-intensive?
Pneumatic conveyor
What is the reason for using a 3-15 psi range in pneumatic control systems?
Standard signal range
Which device prevents reverse movement of bucket elevators?
Backstop
A steam pipe is insulated using two layers of insulating materials, where the material with better insulating property is placed on the outer layer. If the positions of the two insulating layers are interchanged, what happens to the heat conducted through the pipe?
Decreases
Which of the following materials offers the least propagation of heat energy through conduction?
Air #