Analog Electronics: BJT, FET, Op-Amps, Oscillators, and Power Amplifiers

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/23

flashcard set

Earn XP

Description and Tags

Vocabulary practice flashcards covering bipolar junction transistors, field-effect transistors, operational amplifier circuits, feedback oscillators, and power amplifier classifications.

24 Terms

1
New cards

BJT Active Region

The operating state of a bipolar junction transistor where the base-emitter input junction is forward-biased (I/P→FBI/P \rightarrow FB) and the collector-base output junction is reverse-biased (O/P→RBO/P \rightarrow RB), allowing the transistor to operate as an amplifier.

2
New cards

BJT Saturation Region

The operating state of a BJT where both the input and output junctions are forward-biased (I/P→FBI/P \rightarrow FB, O/P→FBO/P \rightarrow FB), causing the transistor to act as a closed switch with maximum collector current.

3
New cards

BJT Cutoff Region

The operating state of a BJT where both the input and output junctions are reverse-biased (I/P→RBI/P \rightarrow RB, O/P→RBO/P \rightarrow RB), resulting in negligible leakage current and causing the device to act as an open switch.

4
New cards

Stability Factor (SS)

A parameter defined as the rate of change of collector current with respect to reverse saturation leakage current: S=∂IC∂ICBOS = \frac{\partial I_C}{\partial I_{CBO}}, evaluated while keeping current gain β\beta and base-emitter voltage VBEV_{BE} constant.

5
New cards

Early Effect (Base-Width Modulation)

The phenomenon in a BJT where variations in the collector-base reverse-bias voltage modulate the effective width of the base region, altering transistor current and contributing to a finite output impedance.

6
New cards

Approximate Analysis Condition (Voltage Divider Bias)

The criterion βRE≥10R2\beta R_E \ge 10 R_2, which determines whether the base current IBI_B is sufficiently small compared to the divider current to allow approximate bias calculations without Thevenin equivalence.

7
New cards

Common Collector Configuration (Emitter Follower)

A transistor configuration where input is supplied to the base and output is drawn from the emitter, characterized by high input impedance, low output impedance, and a voltage gain slightly less than unity (Av≈1A_v \approx 1).

8
New cards

Darlington Connection

A composite circuit formed by connecting two bipolar transistors such that the emitter current of the first drives the base of the second, yielding a total current gain approximately equal to the product of both individual gains: βD≈β1β2\beta_D \approx \beta_1 \beta_2.

9
New cards

Shockley's Equation

The mathematical transfer characteristic defining the drain current IDI_D of a JFET in the active region: ID=IDSS(1−VGSVP)2I_D = I_{DSS} \left(1 - \frac{V_{GS}}{V_P}\right)^2, where IDSSI_{DSS} is the saturation drain current and VPV_P is the pinch-off voltage.

10
New cards

Pinch-off Voltage (VPV_P)

The critical gate-to-source reverse voltage (VGSV_{GS}) at which the depletion regions touch across the channel, causing drain current IDI_D to drop to zero.

11
New cards

JFET Transconductance (gmg_m)

The dynamic slope relating drain current variation to gate-to-source voltage variation, calculated as gm=gm0(1−VGSVP)g_m = g_{m0} \left(1 - \frac{V_{GS}}{V_P}\right), where the maximum value at zero bias is gm0=2IDSS∣VP∣g_{m0} = \frac{2 I_{DSS}}{|V_P|}.

12
New cards

Virtual Ground Concept

The operating condition in an ideal op-amp circuit with negative feedback where the infinite open-loop gain causes the differential input voltage to become zero (Vd=VA−VB=0V_d = V_A - V_B = 0), holding the inverting terminal at the potential of the non-inverting terminal without drawing input current.

13
New cards
<p>Non-Inverting Amplifier Configuration</p>

Non-Inverting Amplifier Configuration

An operational amplifier circuit where the input voltage is connected to the positive terminal and a feedback voltage divider (RfR_f, R1R_1) is connected to the negative terminal, establishing a closed-loop gain of Av=1+RfR1A_v = 1 + \frac{R_f}{R_1}.

14
New cards

Inverting Op-Amp Closed-Loop Gain

The voltage amplification factor of an inverting op-amp configuration given by Av=−RfR1A_v = -\frac{R_f}{R_1}, introducing a 180∘180^\circ phase shift between the input and output voltages.

15
New cards

Summing Amplifier

An op-amp circuit that scales and sums multiple input voltages into a single inverted output according to the relationship Vo=−(RfR1V1+RfR2V2+RfR3V3)V_o = -\left(\frac{R_f}{R_1} V_1 + \frac{R_f}{R_2} V_2 + \frac{R_f}{R_3} V_3\right).

16
New cards

Op-Amp Integrator

An operational amplifier circuit featuring an input resistor RR and a feedback capacitor CC, generating an output voltage proportional to the time integral of the input signal: vo(t)=−1RC∫vi(t) dtv_o(t) = -\frac{1}{R C}\int v_i(t)\,dt.

17
New cards

Op-Amp Differentiator

An operational amplifier circuit with a capacitor CC at the input and a resistor RfR_f in the feedback path, generating an output voltage proportional to the time derivative of the input signal: vo(t)=−RfCdvi(t)dtv_o(t) = -R_f C \frac{dv_i(t)}{dt}.

18
New cards

Barkhausen Criterion for Oscillation

The mandatory conditions for sustained sinusoidal oscillations in a feedback system, requiring the magnitude of loop gain to equal unity (∣βA∣=1|\beta A| = 1) and the total loop phase shift to equal zero degrees (∠βA=0∘\angle \beta A = 0^\circ).

19
New cards
<p>Wien Bridge Oscillator</p>

Wien Bridge Oscillator

An RC feedback oscillator using a lead-lag frequency-determining network that oscillates at resonant frequency f=12πRCf = \frac{1}{2\pi R C}, requiring an amplifier gain of Av=3A_v = 3 to overcome the feedback network attenuation factor of VoutVin=13\frac{V_{out}}{V_{in}} = \frac{1}{3}.

20
New cards

Class A Power Amplifier

A power amplifier whose active device conducts over the full 360∘360^\circ cycle of the input signal, having poor efficiency with a theoretical maximum of 25%25\% in directly-coupled designs due to continuous DC current draw.

21
New cards

Class B Push-Pull Amplifier

A power amplifier utilizing complementary pairs of transistors where each transistor conducts for exactly one half-cycle (180∘180^\circ), achieving a higher theoretical conversion efficiency of η=π4≈78.5%\eta = \frac{\pi}{4} \approx 78.5\%.

22
New cards

Crossover Distortion

Distortion near the zero-voltage crossing point in Class B push-pull amplifiers caused by the inherent threshold voltage (≈0.7 V\approx 0.7\,V) required to forward-bias each transistor's base-emitter junction.

23
New cards

Class AB Power Amplifier

A power amplifier configured with small diode or resistor pre-biasing so that each active device conducts slightly more than 180∘180^\circ of the input waveform, eliminating crossover distortion while preserving high efficiency.

24
New cards

Class C Power Amplifier

A high-efficiency tuned amplifier where the active device conducts for significantly less than half of an input cycle (<180∘< 180^\circ), capable of achieving operating efficiencies approaching 100%100\%.