1/72
Looks like no tags are added yet.
How does your receiver calculate estimated position?
using psuedorange from SV. Uses orbital elements for a specific SV and current time
ECEF XYZ
Earth centered, Earth Fixed XYZ coordinates
How is distance measured in GNSS?
Measure signal travelling time between artificial satellite and receiver
Range
Distance between two points (GNSS receiver and Satellite)
Range Formula
Range = c(delta t)

Similarity between GNSS and Trilateration
Relies on measurememt of distance to fixed positions
Difference between GNSS and Trilateration
Distances are not measured to control points on surface of earth but rather measured to satellites in orbits at a nominal altitude above earth
Principle of positioning drawing
asdfasdfasdf
How to monitor GNSS signal inaccuracy?
Set up a base station and rover move from place to place calculated relative to base
Base station
Setting a GPS receiver on a station whose position is known
Latency
Time taken for a system to compute corrections and transmit them to users in real-time
Difference between accuracy and precision
Accuracy is average closer to real value while precision is ability to recreate the exact same result or how close repeated measurements are to each other
Accuracy standard of receiver
constant instrument error a and error proportional to distance b ppm
RMS
Root mean square
Accuracy specification formula
RMS sigma = Root (a² + (bxd)²)
Code Phase Receiver A.K.A.
Code correlating
Code phase receiver
requires access to satellite navigation message of P or C/A code amd relies on it to provide almanac.
unique capability to begin calculation without approximate location and time
Code Phase Receiver capability
anywhere fix capability
Autocorrelation technique
Determine range by measuring signal travel time from satellite by comparing PRN with identical code from satellite
Do not correlate until replica code in receiver is shifted
What reveals propagation delay
Time shift
Propagation delay
Time it took for sigmal to make the trip from satellite to receiver
code locked
Receiver generated code aligned with received code
Trackig
receiver is continuosly locked and continuosly shifted to match
Carrier Phase receiver
Utilizes GPS signal itself to calculate a position
Two types of carrier phase receiver
Single frequency
Dual Frequency
Single Frequency
Tracks L1 signal and has lower price because of fewer components. develop relative position accurate over less than 50km where ionosphere effects can be ignored
Dual Frequency
tracks both L1 and L2 signal. More effective for longer baselines more than 50km where ionosphere effects have larger impact
Absolute Positioning A.K.A.
Point positioning, point solution or single receiver positioning and code phase measurement
Why is absolute positioning known as code phase measurements
It measures time between transmission and reception of PRN codes.
Coordinates of a receiver at an unknown are sought with respect to earths reference frame using known position of GPS satellites being tracked
Absolute positioning accuracy real time
+- 10-15 meters
Pseudo-range
A time based distance measurement based on code transmitted by GPS satellite and correlated with replica generated in receiver
Why is C/A code pseudorange less precise than P code pseudorange
Precision is a function of resolution of code.
Equation 1 pseudorange
P^s r = c( tr-ts)
Equation 1 Pseudorange
R^sr (t) = c[(tr+6[]r)-9ts+[]s)
Speed of light
299792458 m/s
GPS SATELLITE RECEIVER clock diagram
asdfasdfasdf
Equation 4 true range xyz
Root ((xs-xr)²+(yx-yr)²+(zs-zr)²)
Equation 5 Observed range from r to s
Rrs= Equation 4 + c([]r-[]s)
Linearized Model
Taylor series
Delta R = dr/dx delta x + dr/dy delta y + dr/dz delta z + dr/d offset delta offset
Linearized Model Matrix
b=Ax + v
Nonlinear Model
Rrs= prs + c([]r-[]s) + dp + dion + dtrop + emp + ep
Relative positioning A.K.A.
Differential positioning
Differential positioning technique
Coded pseudorange measurements
Relative positioning technique
Carrier phase measurement
Relative positioning
Minimum of 2 receiver. higher accuracy of 1cm + 2ppm
Relative positioning precision increases with what
decrease in wavelength
L1 wavelength
29cm
L2 wavelength
24cm
C/A wavelength
200cm
P wavelength
30cm
Static surveying
Most reliable, post processed standard when measuring lines over 20km
Static surveying application
geodetic control
contro densification
precise engineering survey
Rapid static surveying
Base re,aims stationary while rover collects data for a preiod of 2 to 10 minutes up to 25km
loss of signnal now allowed used for short range survey
Rapid Static Surveying observation sessions
single 20 mins + 2min/km @ 5 second epochs
Dual 5-10 minutes + 1min/km @ 5s epoch
Reoccuply survey A.K.A.
Pseudo-kinematic
Re-Occupation Survey
not as dependent on satellite geometry. reoccupation of point pairs at least one hour after initial occupation
rovers occuuply for 10-15 minute reoccuply 1 hour
loss of satellite lock not allowed
Kinematic Surveying innovator
Dr. Benjamin Remondi in mid 1980s
Kinematic Surveying
Mobile rover carried to each site for 5-30 seconds them precossed against a static base station to remove error
Kinematic Surveying stop and go
A.K.A. Semi Kinematic
first determine initial integer ambiguity parameters then rover moves to first unknown then 30 seconds move to second repeat. satellite lock must be maintained
Kinematic Surveying: Real Time Kinematic
up to 10 to 20 km limited range with respect to base station and need of communication channel for real time application convergence time needed. track GNSS signal continously
Carrier Phase measurement
Combination of unmodulated carrier from gps with replica of carrier generated within receiver
Carrier Phase Observable A.K.A.
Reconstructed carrier phase or carrier beat phase observable
Beat
pulsation from combination of two waves with different frequencies
Doppler Effect
Difference between two carriers happens its trip from sattelite to receiver
3 parts of carrier phase observable
Fractional instantaneous phase alpha
Integer cycle ambiguity N
Value Beta
Fractional Instantaenous phase
Established at first instance of lock on
Integer cycle ambiguity N
Number of full phase cycles between receiver and satellite at first instance of receiver lock on
Value (Beta)
The count of number of full phase cycles coming in throughout the observation. record of consecutive change in full phase cycles
Total Phase (Phi) formula
phi = alpha + beta + N
Cycle ambiguity problem
the unknown number of whole wavelengths within a set of measurement. changes everytime receiver loss the lock on the signal producing jumps
Clock time as a fynction of phase and nominal frequency formla
page 131
Differencing technique
combining simultanous observables
Differencing technique Purpose
Eliminate embedded biases
Reveal the actual vectors between two or more receivers