AGK: Turbines

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/41

encourage image

There's no tags or description

Looks like no tags are added yet.

42 Terms

1
New cards

Bypass Ratio:

ratio of the bypass massflow, to the compressor mass flow

2
New cards

Jet Engine Process:

  • all steps happen at the same time (continuous)

  • Pressure is constant through the combustion chamber.



3
New cards

Thrust Formula:

Thrust = massflow (jet velocity - airspeed)

T = M * (Vj - Vv)
J is before V in the alphabet.

Specific thrust is the efficiency of the engine, thrust per unit of air mass flow.

More inlet airspeed results in less thrusts, as more ram pressure in the inlet meaning less of a differential from the front to back

4
New cards

Specific Fuel Consumption

Jets: flow per thrust (kg per hour of thurst)
Props: flow per power (kg per unit of shaft power)

5
New cards

Free Turbine:

The first turbine is linked to the compressor.

The next set of turbine is the FREE TURBINE - this is not connected to the compressor, instead it drives a power shaft, which would go to a reduction gearbox, then to a propellor.

It is not coupled to the compressor art all, so is free to rotate at its own speed.

6
New cards

Free Power Turbine and Constant Speed propellers

If power increases in the turbine, the HP spool increases, and EGT increases
if power decreases in the turbine, the HP spool decreases and EGT also decreases

Propellor stays constant - by adjusting the propellor angle.

When power increases blade has more angle (course), so it drags more (so it slows the prop down to remain constant)

when power decreases, the blade has less angle (fine), so it has less drag and goes faster.

7
New cards

Turbo Jet Engine:

a simple turbine engine, that produces all thrust from the exhaust from the turbine section, no fan, no bypass.

8
New cards

Number of Spools:

a spool is a compressor and the turbine that drives, it they connect via a shaft.

The compression can be split into low and high pressure stages. This is a two spool engine

for very high pressure ratios, a third intermediate pressure spool is added.

9
New cards

Convergent Ducts:

velocity increases, and static pressure decreases - temp also decreases (as heat is absorbed into the kinetic energy)

(it isn’t compressing the air, only reducing the space for it to flow)

10
New cards

Divergent Air Intake

causes incoming air to decelerate, as the flow slows its dynamic pressure decreases, and static pressure increases.

This is the ram air recovery, the faster the aircraft flies, the more ram air.

Divergent: Static pressure increase, velocity decreases and temperature increases
why increase in temp? the velocity slows and the kinetic energy is converted into heat.

11
New cards

Turbine Stage:

The high pressure air from the combustion chamber works on the turbine blades, the turbine converts this into kinetic energy, so the pressure decreases, this energy is lost, so pressure and temperature decrease in the turbine stage, (as the temp is converted to kinetic energy).


12
New cards

Which spool is spun by air starter?

HP Spool

13
New cards

Jet turbines vs turbofans

Jet turbos didn’t bypass any air, so all thrust came from the combustion and exhaust.

this was a small amount of air by a high speed. this lost a lot of energy to noise, heat and friction

Modern engines bypass most of the air, they move a large amount of air by a smaller speed.

This means the hot exhuast gases are slower than a jet turbine.

14
New cards

Impulse and Reaction Turbines

a turbine stage is a fixed nozzle, and then a rotating turbine.

Think: we want to extract the kinetic energy, so the pressure must drop.

NT - IDC RCD

No thanks
I Don’t Care

Really couldn’t Decide


Nozzle (stator)

Turbine (Rotor)

Impulse

Down

Constant

Reaction

Constant

Down



Impulse use a convergent nozzle to accelerate airflow, then use bucket style on the turbine, to turn that fast airflow the other way, giving the turbine an -impulse.

Reaction doesn’t use a convergent nozzle, it just guides the air at the correct angle to the turbine blade, the turbine then turns and the air is converged on the turbine.


<p>a turbine stage is a fixed nozzle, and then a rotating turbine. <br><br>Think: we want to extract the kinetic energy, so the pressure must drop.<br><br>NT - IDC RCD<br><br>No thanks<br>I Don’t Care</p><p>Really couldn’t Decide<br></p><table style="min-width: 202px;"><colgroup><col style="width: 152px;"><col style="min-width: 25px;"><col style="min-width: 25px;"></colgroup><tbody><tr><td colspan="1" rowspan="1" colwidth="152" style="width: 152px; height: 14px; border-style: solid; border-width: 1px; padding: 4px;"><p></p></td><td colspan="1" rowspan="1" style="width: 151px; height: 14px; border-style: solid; border-width: 1px; padding: 4px;"><p>Nozzle (stator)</p></td><td colspan="1" rowspan="1" style="width: 152px; height: 14px; border-style: solid; border-width: 1px; padding: 4px;"><p>Turbine (Rotor)</p></td></tr><tr><td colspan="1" rowspan="1" colwidth="152" style="width: 152px; height: 13px; border-style: solid; border-width: 1px; padding: 4px;"><p>Impulse</p></td><td colspan="1" rowspan="1" style="width: 151px; height: 13px; border-style: solid; border-width: 1px; padding: 4px;"><p>Down</p></td><td colspan="1" rowspan="1" style="width: 152px; height: 13px; border-style: solid; border-width: 1px; padding: 4px;"><p>Constant</p></td></tr><tr><td colspan="1" rowspan="1" colwidth="152" style="width: 152px; height: 14px; border-style: solid; border-width: 1px; padding: 4px;"><p>Reaction</p></td><td colspan="1" rowspan="1" style="width: 151px; height: 14px; border-style: solid; border-width: 1px; padding: 4px;"><p>Constant</p></td><td colspan="1" rowspan="1" style="width: 152px; height: 14px; border-style: solid; border-width: 1px; padding: 4px;"><p>Down</p></td></tr></tbody></table><p><br><br>Impulse use a convergent nozzle to accelerate airflow, then use bucket style on the turbine, to turn that fast airflow the other way, giving the turbine an -impulse.<br><br>Reaction doesn’t use a convergent nozzle, it just guides the air at the correct angle to the turbine blade, the turbine then turns and the air is converged on the turbine. </p><p></p>
15
New cards

Centrifugal Compressor

Air enters through the eye of the impeller, it is then caught by curved vanes that rotate at high speed. The centrifugal force throws the air outward.
This gives it a large amount of kinetic energy and in the process raises the total pressure.

The air then enters a diffuser where it slows, converting the dynamic into more static, the high pressure air then enters the combustion chamber.

16
New cards

Axial Flow Compressor

Has a rotor and stator, convert kinetic energy into pressure energy.

a stage has a rotor, and then a stator.
the rotating blade adds energy to the air, increasing total pressure, the stator then slows and redirects it, converting the dynamic to static pressure.

Figure 1 is correct, it would trap some air, push it to the stator.
figure 2 would move it backwards

<p>Has a rotor and stator, convert kinetic energy into pressure energy.<br><br>a stage has a rotor, and then a stator.<br>the rotating blade adds energy to the air, increasing total pressure, the stator then slows and redirects it, converting the dynamic to static pressure.<br><br> Figure 1 is correct, it would trap some air, push it to the stator.<br>figure 2 would move it backwards </p>
17
New cards

Combustion Chambers:

Can Type: easy maintenance, performance bad
server flame tubes, each in its own case, only two igniters placed in lower chambers, but they are interconnected so the flame can pass through all cans.


Tubo-annular → middle ground
a hybrid that combines individual flame cans, enclosed in a common continuous air casing.

Annular: best performance, hard to maintain.
a continuous circular liner and shroud, sharing undivided combustion space.


18
New cards

Compressor Stall & Surge

Stall:
Occurs when there is an imbalance between airflow supply and the airflow demand. It stalls the rear stages.

E.g low RPM when it is designed for high pressure.

Surge:
unstable condition when airflow breaks down, produces violent reverse flow of hot air from the combustion chamber back to the intake.

To keep the operating point below the surge line, two protection devices are used, variable inlet guide vanes VIGVs, and variable stator vanes adjust the angle of the airflow.
Also bleed valves located between compressor stages open at low speed, and during rapid changes, to dump air. This reduces the pressure ratio and increases the mass flow.


Difference between a Stall and Surge:

Stall is a partial breakdown of airflow in the engine, surge is a total breakdown of airflow, causing reverse of engine gases, loud bangs, more severe.

19
New cards

Compressor vs Turbine (Rotors and Stators)

The turbine has a stator then a rotor.
a compressor has a rotor then a stator
think alphabet
C R S T
Turbine is closer to Stator, so Stator first
Compressor is closer to Rotor so Rotor first.

The turbine has stator (nozzle), then turbine (Rotor), think NO THANKS.

20
New cards

Supersonic Air (Divergent inlet)

Super sonic air behaves in the opposite to subsonic
it accelerates in a divergent duct

Think rocket engine, divergent nozzle, increases velocity.

21
New cards

EGT

Indicator of engine health and performance

EGT is high when engine is high thrust, but can also be high due to issues.

EGT increasing (without increase to power), there may be a blockage at the front (ice?) , reducing the incoming air. Less air to absorb the heat.

22
New cards

Thrust Reversal:

Clamshell doors and bucket deflect the hot core

cascading vanes combined with translating cowl redirect the cold bypass flow.


23
New cards

Compressor:

Air hits the first rotor, the rotor is connected to the turbine, so it has drive, which is spinning it, pushing the air to the stator, which reduces the velocity and increases the static.

compressor is made up of many stages, increasing the pressure over the last, the compressor rotor acts on the air to increase the total pressure, the stator realigns, reduces the velocity and increases the static.

Compression Ratios:

Axial compressor, each stage increases by 10-20%, 1.1:1 to 1.2:1
There are around 30 stages, Total axial is around 38:1


Centrifugal Compressor:
Increase by 4, so ratio of 4:1
centrifugal total is 12:1 (x3)


24
New cards

Active Clearance Control:

Acts on the casing, to cool / heat it.

Heating = expands the case, the tip clearance increases
cool = contracts the case, clearance decreases

25
New cards

Engine Inlet

Inlet is divergent for subsonic aircraft.
This allows the air to slow down, increasing the static pressure.
The temp (static temp) also increases due to the conversion of kinetic dynamic energy.

26
New cards

Variable Bypass Valve:

Stall occurs when there isn’t enough air coming into the engine to match the acceleration of the engine. This leads to stagnation of air at the rear.

27
New cards

FADEC

The FADEC is the system, it has an Engine Control Unit ECU, (which is the computer), it is mounted on the engine.

There are dual channels, it will read input from both sensors. It has 2 systems, only 1 is active at a time, the other is backup.
If 1 fails, you can keep flying on the other.


It includes the ECU and peripherals, wiring, sensors etc.


  • its power sources from from an internal power source only - independent alternator

  • Completely self contained within the engine

  • it is single fault tolerant it will use the second channel if the first fails.

  • it uses dual input logic, almost all control inputs are dual.


28
New cards

Starting a Gas Turbine

Compressor acceleration → ignition on → Fuel injection


Electric starter motor or high pressure air starts the rotation (the HP spool)
the ignition is turned on before the fuel (else fuel could pool in the engine)

The HPSOV high pressure shut of valve is located after the FCU, it opens once ignition started.



An engine cannot be started by batteries as it requires high power for extended period. The risk of starting with a low battery charge could result in a hung start.

29
New cards

Heat Intense Spark:

best ignitor to use, the temp of the spark is very hot, so heats the gases rapidly to ensure ignition in cold temps and high altitude.

30
New cards

Air starter disconnect?

The starter is disconnected from the N2 spool (HP), by centrifugal forces

31
New cards

Trembler Mechanism (vibrator)

It is a DC trembler unit, provides a DC current for generation of higher voltage to ignitorrs

vibrator = DC batteries.

32
New cards

Different Types of Gear Box

Accessory / Auxiliary: = HP Shaft / engine oil

  • Is part of the engine (just not in the core)

  • driven by the high pressure shaft.

  • it drives accessories like fuel pumps, oil pumps, generators, et

  • it is the main gearbox.

  • uses the engine oil supply (as they are close may as well use the same system)

Secondary / Supplemental = LP Shaft - uses own oil




33
New cards

Hot Start:

Engine hangs, then continues to accelerate.

usually caused by early starter cut out, fuel mis, leading to excess fuel in the combustion chamber, a strong tail wind.
Intermittent light at very low RPM, followed by increase in EGT. A hot start occurs when an aircraft engine begins to accelerate unexpectedly after a hang, often due to early starter cutout or fuel mismanagement, resulting in excess fuel in the combustion chamber. This can lead to abnormal increases in exhaust gas temperature (EGT) at low RPM.

34
New cards

Hung Start

Fails to accelerate because of too low start pressure.
results in N2 speed stabilising lower than normal RPM, and EGT increase.

Need to shut down the engine.

35
New cards

Compressor Stall due to in-flight Turbulence:

Can be resolved by the Variable inlet guide vanes.
The compressor blades stall as angle of attack isn’t suitable, the guide vanes adjust the airflow to make it suitable.

The bleed air valve is more of a secondary feature, mostly used in start and low speed.

36
New cards

What indications are used to monitor a turbine engine:

NOT hydraulics, or OAT.

37
New cards

Engine Seizure

The cool down:
running the engine at low power for a few mins in order to cool it.
The turbine blades and engine casing benefit most, as if hot engine is shut down, the thin engine casing will cool and contract quicker than the thick turbine blades. So the casing would shrink faster and it could cause the seals on the turbines to be crushed, seizing the blade to the casing.

38
New cards

Engine Oil Pressure:

The most common issue is low oil flow. Usually due to lack of oil, leaks, blockages.

The oil pressure will drop, less oil flow around the engine, the oil remaining will take more heat per part oil, so the temp will increase

Low oil = high oil temp.

39
New cards

Propeller Blade Pitch:

Alpha - flight idle to max power - controlled by power lever

Beta - selected by moving the power lever back via a notch.

Ground fine pitch is in the BETA range
Beta range is from flight fine pitch to full reverse.


40
New cards

Continuous Ignition

Will be auto triggered when:

  • engine anti ice on

  • stick shaker

  • max and min thrust settings


41
New cards

Flat Rated:

engines are capable of producing more thrust than is needed, so it is flat rated.

This means, that for an OAT below a certain value, constant thrust will be maintained for the max level.

As the air temp increases, or at high altitude, the air is less dense, so more work is needed to produce the same thrust. Which means the engine gets hotter, and so max thrust is now limited by a max turbine gas TGT.

Essentially it allows the max thrust level to increase as OAT increases, until it reaches the max TGT.

42
New cards

Thrust and SFC

As altitude increases, the air gets less dense, which results in a decrease in thrust.

Specific Fuel consumption decreases with increasing pressure altitude