1/30
Looks like no tags are added yet.
What is a transducer?
It changes one kind of energy to another. In sound reinforcement, this usually means to go from acoustic energy to electrical energy or vice-versa. These occur as a microphone or a speaker (but are not limited to that, since guitars have pickups).
What is an amplifier?
It makes an electric copy of a electrical signal. It increases the electrical energy, called gain.
What is an pre-amp?
It is the first and most crucial gain stage as it provides amplification to the microphone so that the mixing board can manipulate the signal efficiently.
Once it is electrical energy, we can change the current by altering the frequencies of the sound or add special effects to the sound.
What is a dynamic mic?
The most widely manufactured ones, least expensive and most durable. They use a principle of voltage in response to the sound waves via a magnet.
Condenser mics
They use electrostatic and are known for their accuracy and strength of high frequencies. They require a power supply (phantom power) and are not as durable as dynamic mics.
Piezo-electric mics
Contact mics that means they must be fastened to a vibrating plate on the instrument (usually made of wood). They are most common on wooden instruments such as acoustic guitars.
Direct boxes (aka Direct Input or DI)
Takes a feed directly from an instrument into the pre-amp. They also use phantom power.
Mixing consoles/The Board
Allows the signals generated by the microphones to be mixed together. Each sound goes through a channel and the electrical current is either restricted or amplified to achieve the volume for that channel.
Mixing board process
The first stage in the console is the pre-amplifier (pre-amp) that amplifies the signal from the mic to a level the console can work with (line level).
Compressor
regulates volume after the initial gain stage by controlling dynamics.
Mixer channels
Preamp
EQ
Inserts: Dynamic processors
Auxiliary Sends
Channel Faders
Sub misex/Busses
Master section: master faders, auxiliary returns/effects returns
Equalization
A filter limits frequencies above or below fixed point(s), such as a high pass filter (HPF) and low pass filter (LPF).
Cut-only. HPF and LPF fall into this category, but so do feedback eliminators. This type will not let you increase frequencies.
Sweep able or variable frequency. Parametric, quasi-parametric or semi-parametric EQs fall into this category.
Graphic (Peak/Dip) EQ. 1/3 Octave means there is 1/3 of an octave between bands.
Shelving
Human hearing range
20 Hz-20 kHz.
Dynamic processors
Gates eliminate low volume sounds. Expanders reduce low volume sounds and are not as severe.
Compressors regulate high volume sounds on a ration principle: for every x of increase, only y of output.
Limiters are compressors with ratios over 10:1, sometimes as severe as what is referred to as a ‘brick wall’ limiter
Gates
Gates eliminate low volume sounds
Expanders
Expanders reduce low volume sounds and aren not as severe as agtes.
Power amp
The level that comes out of the console must be amplified to a stronger level so the speakers can use.
Speakers
Speakers create the acoustic energy, but the type of speaker is important as larger ones are more efficient at carrying lower frequencies due to the direction the sound comes out of the speaker.
What is a crossover?
A crossover helps split the signal from the output of the console into two or more frequencies then is sent to the power amp prior to arriving at the speakers. This is an efficient way of isolating energy for each speaker.
Speaker/driver
The speaker (often referred to as the driver) that accomplishes the actual transduction.
Speaker/driver design
A good designed driver enclosure produces smooth frequency curve throughout its range
Crossovers
Use of filters: Low-pass, band pass, hi-pass. They range from 2, 3 or 4 way.
Some cabinets have built in crossovers presets via circuits in the enclosure
Effective choice of electronic crossover points: frequency response curves of each component, and the practical low and high frequencies of the components in relation to the required output level
Woofer
A direct radiator is the large vibrating element, known in slang as the woofer. It is often in some sort of enclosed or semi-closed cabinet
Basic Horns
Generally more efficient than direct radiators as they afford better control of the directional pattern of the output sound. Basic function is to allow the vibrating element to be much smaller and move within a smaller excursion, allowing a more accurate reproduction of the waveform while still providing substantial output.
Low frequency horns
Low frequency horns are usually very large speaker cabinets and are folded to fit the horn into a smaller space. These cabinets are often referred to as “w-bins” since they have the shape of a w.
Ringing out of a system
Set all graphic EQ sliders to flat
Bring up output gain until one frequency begins to feedback
Find the fader that is that frequency and bring it back until the ring is gone.
Repeat for more frequencies
Bring back the output after it’s finished to just under the last frequency feedback was.
Dispersion
the ability of a component to spread out the sound to a certain angle, important towards eliminating feedback
Force majeure
“act of god” The contracts that are entered into in support of a live event have a clause addressing these acts of God, other factors that may be out of everyone’s control.
Deadwood
Refers to unsold tickets. Promoters like this to be as close to zero as possible.
Paper the house
Give away tickets. If there are a lot of unsold tickets to an event, some may be given away, or the price of certain sections may be drastically reduced to encourage additional ticket sales.
Hall fee
The hall fee is meant to cover the cost that the venue incurs to make the sale, plus the venue’s profit from the sale.