1/139
Looks like no tags are added yet.
C. Taxi and takeoff operations are permitted, providing the takeoff operations are toward the visible green threshold light
(Refer to Figure 138 below). What night operations, if any are authorized between the approach end of the runway and the threshold lights?
A. Arrows leading to the threshold mark
Which runway marking indicates a displaced threshold on an instrument runway?
B. 1,000 feet
(Refer to Figure 137 below.) What is the distance (A) from the beginning of the runway to the fixed distance marker?
B. 500 feet
(Refer to Figure 137 below.) What is the distance (B) from the beginning of the runway to the touchdown zone marker?
B. 500 feet
(Refer to Figure 137 above.) What is the distance (C) from the beginning of the touchdown zone marker to the beginning of the fixed distance marker?
B. Edge of the ILS critical area
The “ILS critical area boundary” sign identifies the
B. an entrance to a runway from a taxiway
The “runway hold position” sign denotes
A. Top red
(Refer to Figure 254 on page 161.) Which of the signs in the figure is a mandatory instruction sign?
C. Bottom Yellow
(Refer to Figure 254 on page 161.) While clearing an active runway, a pilot is clear of the ILS critical area when passing which sign
B. Top red (A)
(Refer to Figure 254 below.) Which of these signs prohibits an aircraft from entering an area on the airport?
C. Bottom yellow
(Refer to Figure 254 below.) Which sign indicates to hold short of the ILS critical area?
C. The direction to takeoff runways
Destination signs indicate
B. Defines direction and designation of exit taxiway from runway
What is the purpose of the runway exit sign?
B. white lettering with a red background
(Refer to Figure 94 on page 163.) Mandatory airport instruction signs are designated by having
B. Mandatory instruction sign
(Refer to Figure 94 on page 163.) What sign is designated by illustration 7?
A. White with a red background
(Refer to Figure 94 on page 163.) What colors are runway holding positon signs?
B. yellow, and the dashed lines are nearest the runway
(Refer to Figure 94 on page 163.) Hold line markings at the intersection of taxiways and runways consist of four lines that extend across the width of the taxiway. These lines are
A. identifies where aircraft hold short of the runway
“Runway hold position” markings on the taxiway
C. paved area where aircraft entry is prohibited
The “No Entry” sign identifies
A. Indicates designation and direction of exit taxiway from runway
When exiting the runway, what is the purpose of the runway exit sign?
B. designation and direction of taxiway leading out of an intersection
When turning onto a taxiway from another taxiway, the “taxiway directional sign” indicates
C. 150
Enhanced taxiway centerline markings are enhanced for a maximum of how many feet prior to the runway holding position markings?
B. highlight an approaching runway holding position marking
The purpose of an enhanced taxiway centerline is to
A. points toward a named taxiway that leads off the runway
A runway exit sign
B. direction to the takeoff runway
Within aircraft movement areas, “destination signs” identify the
C. 7
(Refer to Figure 135 below.) Which illustration would a pilot observe if the aircraft is above both glidepaths?
A. 4
(Refer to Figure 135 below.) Which illustration would a pilot observe if the aircraft is below both glidepaths?
B. 5
(Refer to Figure 135 below.) Which illustration would a pilot observe when on the lower glidepath?
B. Safe obstruction clearance in the approach area
Which approach and landing objective is assured when the pilot remains on the proper glidepath of the VASI?
A. white and the far bar as red
When on the proper glidepath of a 2-bar VASI, the pilot will see the near bar as
B. If departing to the high side of the glidepath, the far bars will change from red to white
Which of the following indications would a pilot see while approaching to land on a runway served by a 2-bar VASI?
C. level off momentarily to intercept the proper approach path
If an approach is being made to a runway that has operating 3-bar VASI and all the VASI lights appear red as the airplane reaches the MDA, the pilot should
C. constitute a 2-bar VASI for using the upper glidepath
The middle and far bars of a 3-bar VASI will
C. 11
(Refer to Figure 136 on page 169.) Which illustration depicts a “slightly low” (2.8 degree) indication?
C. below the glidepath
(Refer to Figure 136 on page 169.) As you emerge from the clouds during an instrument approach and make visual contact with the runway environment, you see PAPI lights corresponding to those depicted in illustration 12. You are
B. 10
(Refer to Figure 136 on page 169.) An “on glidepath” indication is
C. 12
(Refer to Figure 136 on page 169.) Which illustration would a pilot observe if the aircraft is less than 2.5 degrees?
C. 12
(Refer to Figure 136 below.) Which illustration would a pilot observe if the aircraft is far below the glidepath?
A. rapid identification of the approach end of the runway during reduced visibility
The primary purpose of runway end identifier lights, installed at many airfields, is to provide
C. REIL
Which type of runway lighting consist of a pair of synchronized flashing lights, one on each side of the runway threshold?
C. the pilot is lined up with the wrong runway
(Refer to Figure 162 on page 170.) A pilot has accepted a visual approach to RWY 16L at EUG at night. When approaching the runway, the pilot notices runway centerline lights. This indicates
C. of the high angle of attack and high gross weight
Wake turbulence is near maximum behind a jet transport just after takeoff because
B. The upwind vortex would trend to remain over the runway
What effect would a light crosswind of approximately 5 knots have on vortex behavior?
C. Light quartering tailwind
What wind condition prolongs the hazards of wake turbulence on a landing runway for the longest period of time?
C. Beyond the jet’s touchdown point
When landing behind a large jet aircraft, at which point on the runway should the pilot plan to land?
B. The upwind vortex would tend to remain over the runway
(Refer to Figure 158 on page 172.) With winds reported as from 330 degrees at 4 knots, a pilot is given instructions to taxi to runway 4 for departure and to expect takeoff after an airliner departs from runway 29. What effect would the pilot expect from that airliner’s vortices?
A. Climb on the centerline of the airway except when maneuvering to avoid other air traffic in VFR conditions
Which procedure is recommended while climbing to an assigned altitude on the airway?
C. Execute gentle banks, left and right, at a frequency which permits continuous visual scanning of the surrounding airspace
What is expected of a pilot on an IFR flight plan if descending or climbing in VFR conditions?
B. When weather conditions permit, regardless of whether operating under IFR or VFR
When is a pilot on an IFR flight plan responsible for avoiding other aircraft?
C. Seeing and avoiding other aircraft
What responsibility does the pilot in command of an IFR flight assume upon entering VFR conditions?
B. the FSS
The most current en route and destination flight information for planning an instrument flight should be obtained from
C. To advise of changes in flight data which affect instrument approach procedures (IAP), aeronautical charts, and flight restrictions prior to normal publication
What is the purpose of FDC NOTAMs?
B. FAA FSS
From what source can a pilot obtain the latest FDC NOTAMs?
C. Chat Supplement and NOTAMs (D)
Which sources of aeronautical information, when used collectively, provide the latest status of airport conditions (e.g., runway closures, runway lightning, snow conditions)?
A. the ceiling is more than 5,000 feet and visibility is 5 miles or more
Absence of the sky condition and visibility on an ATIS broadcast specifically implies that
B. the ground visibility is less than 3 miles and/or the ceiling is less than 1,000 feet in Class B, C, D, or E airspace
The operation of an airport rotating beacon during daylight hours may indicate that
B. Upon receipt of any official weather, regardless of content change or reported values
When are ATIS broadcast updated?
C. Upon landing, the pilot must close the flight plan by radio or by telephone to any FSS or ATC facility
How is a flight plan closed when the destination airport has IFR conditions and there is no control tower?
A. Initial cruising altitude
(Refer to Figure 1A on page 177.) If more than one cruising altitude is intended, what information should be entered in item 15, “Level,” of the flight plan?
A. Initial cruising altitude
(Refer to Figure 1A on page 177.) What information should be entered in item 15, "Level,” for an IFR flight?
B. The destination airport identifier code
(Refer to Figure 1A on page 177.) What information should be entered into item 16, “Destination Aerodrome,” for an IFR flight?
C. The amount of usable fuel on board expressed in time
(Refer to Figure 1A on page 177.) What information should be entered in item 19, “Endurance,” for an IFR flight?
C. The total amount of usable fuel onboard expressed in hours and minutes
(Refer to Figure 1A on page 177.) What information should be entered in item 19, “Endurance,” for an IFR flight?
B. The ICAO four-letter indicator of the destination airport
(Refer to Figure 1A on page 177.) What information should be entered in item 16, “Destination Aerodrome,” for an IFR flight with an intended stopover of 30 minutes?
C. The point of first intended landing
What point at the destination should be used to compute estimated time en route on an IFR flight plan?
A. A predetermined geographical position used for an RNAV route or an RNAV instrument approach
What is a waypoint when used for an IFR flight?
C. if in VMC outside Class A airspace
A pilot may cancel an IFR flight plan
A. The tower will automatically close the flight plan when the aircraft lands
How should an IFR flight plan be closed at the completion of the flight at a controlled airport?
B. Read back those parts containing altitude assignments or vectors and any part requiring verification
What response is expected when ATC issues an IFR clearance to pilots of airborne aircraft?
B. Destination airport, altitude, DP Name, Number, and/or Transition, if appropriate
Which clearance items are always given in an abbreviated IFR departure clearance? (Assume radar environment.)
B. Name of destination airport or specific fix and altitude
Which information is always given in an abbreviated departure clearance?
B. of the destination airport filed in the flight plan
An abbreviated departure clearance “… CLEARED AS FILED…” will always contain the name
B. The pilot must advise ATC as soon as possible, but no later than 30 minutes, of their intentions if not off by the void time
When departing from an airport not served by a control tower, the issuance of a clearance containing a void time indicates that
C. destination airport and route
On the runup pad, a pilot receives the following clearance from ground control:
CLEARED TON THE DALLAS-LOVE AIRPORT AS FILED -MAINTAIN SIX THOUSAND - SQUAWK ZERO SEVEN ZERO FOUR JUST BEFORE DEPARTURE - DEPARTURE CONTROL WIL BE ONE TOUR FOUR POINT NINER.
An abbreviated clearance, such as this, will always contain the
B. It authorizes a pilot to conduct flight at any altitude from minimum IFR altitude up to and including 6,000
What is the significance of an ATC clearance which reads “…CRUISE SIX THOUSAND…”?
B. Climbs may be made to, or descents made from, 6,000 feet at the pilot’s discretion
What is the significance of an ATC clearance which reads “… CRUISE SIX THOUSAND…”?
C. The pilot has the option to accept or reject all LAHSO clearances regardless of the meteorological conditions
What is the rule for a pilot receiving a “Land and Hold Short Operation (LAHSO) clearance?
A. vacate 4,000 feet without notifying ATC
A “CRUISE FOUR THOUSAND FEET” clearance would mean that the pilot is authorized to
C. When departing from a runway intersection
When should pilots state their position on the airport when calling the tower for takeoff?
B. when the tower instructs the change
During a takeoff into IMC at a controlled field with low ceilings, a pilot should contact departure
B. At all times if the equipment has been calibrated unless requested otherwise by ATC
When should the transponder be on Mode C while on an IFR flight?
C. Maintain an optimum climb on the centerline of the airway without intermediate level-offs until 1,000 feet below assigned altitude, then 500 to 1,500 feet per minute
What is the recommended climb procedure when a nonradar departure control instructs a pilot to climb to the assigned altitude?
B. Advise “unable” and remain clear of clouds
While performing a VFR practice instrument approach, Radar Approach Control assigns an altitude or heading that will cause the pilot to enter the clouds. What action should the pilot take?
C. As rapidly as practicable to 1,000 feet above/below the assigned altitude, and then between 500 and 1,500 feet per minute until reaching the assigned altitude
To comply with ATC instructions for altitude changes of more than 1,000 feet, what rate of climb or descent should be used?
B. When leaving final approach fix in bound on final approach
Which report should be made to ATC without a specific request when not in radar contact?
B. 500 feet per minute and 1,500 feet per minute
When ATC has not imposed any climb or descent restrictions and aircraft are within 1,000 feet of assigned altitudes, pilot should attempt to both climb and descent at a rate of between
B. Your aircraft has been identified on the radar display and radar flight-following will be providing until radar identification is terminated
What does the ATC term “Radar Contact” signify?
A. Fixes selected to define the route
For IFR planning purposes what are the compulsory reporting points when using VOR/DME or VORTAC fixes to define a direct route not on established airways?
B. continue as assigned and query ATC
A pilot has not yet been cleared for the approach but is being vectored to the ILS approach course. It is clear that the pilot will pass throughout the localizer course unless action is taken. The pilot should
A. 40 degrees to the right of the aircraft’s nose
During a flight, the controller advises “traffic 2 o’clock 5 miles southbound.” The pilot is holding 20 degrees correction for a crosswind from the right. Where should the pilots look for the traffic?
C. Reduce IAS to 160 knots and maintain that speed within 10 knots
What is the pilot in command’s responsibility when flying propeller aircraft within 20 miles of the airport of intended landing and ATC requests the pilot to reduce speed to 160? (pilot complies with speed adjustment.)
C. The pilot is to assume responsibility for their own navigation
Upon intercepting the assigned radial, the control advises that the pilot is on the airway and to “RESUME OWN NAVIGATION.” This phrase means that
B. Resume normal position reporting
During the en route phase of an IFR flight, the pilot is advised “Radar service terminated.” What action is appropriate?
A. The pilot should maintain the airway by use of the aircraft’s navigation equipment
What is meant when departure control instructs the pilot to “resume own navigation” after being vectored to a VICTOR
C. Separation from all IFR aircraft and participating VFR aircraft
What service is provided by departure control to an IFR flight when operating from an airport within the outer area of Class C airspace?
B. average TAS changes 10 knots or 5 percent
While on an IFR flight plan, the pilot should notify ATC of a variation in speed when
C. Merely an advisory that indicates an emergency situation is possible should any undue delay occur
What does declaring “minimum fuel” to ATC imply?
C. When leaving an assigned holding fix
Which of the following reports should always be reported to ATC?
C. Before entering Class D airspace
When a pilot required to establish communications with the tower (Class D airspace) if the pilot cancels an IFR flight plan 10 miles
B. Depart the holding fix at the EFC time
Which procedure should a pilot follow if experiencing two-way communications failure while holding at a holding fix with an EFC time? (The holding fix is not the same as the approaching fix.