1/79
Looks like no tags are added yet.
What counts as plagiarism when you paraphrase a source?
Presenting someone else’s idea, result, or explanation in your own words without crediting the source.
How should you use a source’s exact wording in a report?
Put the borrowed wording in quotation marks and cite the source. A citation by itself does not identify which words you copied.
Whose graphics can you use in this course’s lab reports?
Your team must create every photo, graph, plot, and schematic it uses. This also applies to prelabs, summaries, and memos.
What belongs in the abstract of a formal lab report?
State the objective, briefly identify the method, give the main quantitative result, and explain what it means. The abstract should make sense on its own.
What question should the introduction answer?
What did you investigate, why does it matter, and what physical principle or prediction are you testing?
How do results, discussion, and conclusions differ?
Results give the measurements. Discussion explains trends and discrepancies. The conclusion answers the original objective using the strongest numerical finding.
Where do figure captions and table titles go?
Figure captions go below figures. Table titles go above tables. Refer to each figure or table by number in the text.
What makes an experimental plot interpretable on its own?
Label each axis with the quantity and units, distinguish the data series, and write a caption identifying the experiment or conditions being compared.
What is the difference between accuracy and precision?
Accuracy is closeness to a reference value. Precision is agreement among repeated measurements. A miscalibrated sensor can be precise and still read consistently high.
How can you recognize random error, and what does averaging do?
Random error produces scatter among repeated readings. Averaging independent readings reduces its effect on the estimated mean.
How can you recognize systematic error, and how can you check for it?
Systematic error produces a repeatable bias, such as a scale reading 2 g high. Check against a known reference. Repeating and averaging the readings preserves the bias.
How do measurement error, uncertainty, and design tolerance differ?
Error is the difference between a reading and a reference. Uncertainty estimates the range associated with a measurement. Tolerance specifies the allowable variation in a design.
How do you find percent relative uncertainty?
Divide absolute uncertainty by the magnitude of the measured value and multiply by 100%. A reading of 50 ± 2 mm has 4% relative uncertainty.
How do you propagate independent input uncertainties through y = f(x₁, x₂, …)?
Use uᵧ = √[Σ((∂y/∂xᵢ)uᵢ)²]. Evaluate each derivative at the measured values, multiply by that input’s uncertainty, square each contribution, sum, and take the square root.
If one side length s is measured and used in V = s³, how does its uncertainty affect volume?
For small uncertainty, uᵥ ≈ 3s²uₛ, so uᵥ/V ≈ 3uₛ/s. A 1% uncertainty in that one length gives about 3% uncertainty in the calculated volume.
How should you round a result reported with uncertainty?
Choose the significant digits for the uncertainty, then round the measured value to the same decimal place. For example, report 125.0 ± 7.7 cm³.
Using Ohm’s law, what current flows through a 10 Ω resistor connected across 5 V?
I = V/R = 5/10 = 0.5 A.
How much heat does a 10 Ω resistor generate when 5 A flows through it?
P = I²R = 5² × 10 = 250 W. For a resistor, VI and V²/R give the same power.
Which actuator would you choose to lock and unlock a drawer with a short straight stroke?
A solenoid. Energizing its coil creates a magnetic field that pulls a plunger. A spring can provide the return stroke.
What is commutation in an electric motor?
Switching current between windings at the correct rotor positions so torque continues in the desired direction.
How does commutation differ between a brushed and a brushless DC motor?
A brushed motor uses brushes and a mechanical commutator. The lab’s brushless motor uses Hall sensors to detect rotor position and electronics to switch the windings.
What is PWM duty cycle, and what average voltage does 60% duty produce when switching between 0 and 10 V?
Duty cycle is on-time divided by period. The average applied voltage is 0.60 × 10 V = 6 V.
Why does a linear motor amplifier generally produce more heat than a PWM drive?
The linear device drops voltage while carrying motor current, dissipating P = Vdrop × I. A PWM switch spends most of its time either off or fully on.
What does a stepper motor do with each step command?
It advances by a discrete angle. At 1.8° per full step, one revolution requires 360°/1.8° = 200 full steps.
How do full stepping, half stepping, and microstepping differ?
Full stepping uses the motor’s full-step angle. Half stepping divides it by two. Microstepping controls winding currents to create finer intermediate positions.
Why might an open-loop stepper need a home switch?
The controller counts commanded steps, but the motor can miss steps under load. Homing reestablishes a known physical position.
What controls the commanded angle of a hobby RC servo?
The width of each repeated control pulse. The servo measures its shaft position internally and drives the motor until it reaches the commanded angle.
Which actuator suits continuous rotation, commanded shaft angle, and incremental rotation?
A DC motor suits continuous rotation, an RC servo suits a commanded angle within its travel, and a stepper suits rotation in discrete increments.
What is sensor calibration, and how is it verified?
Apply known physical inputs and record the sensor output to establish a conversion. Verify it by using the conversion to predict a known input and checking the error.
In a linear sensor calibration V = mx + b, what do gain and offset represent?
Gain m is the change in voltage per unit change in input. Offset b is the output at zero input. Recover the physical input using x = (V − b)/m.
How does a rotary potentiometer measure shaft angle?
Its wiper moves along a resistive track. Wired as a voltage divider, it gives an output voltage that varies approximately linearly with angle over its usable travel.
How does an incremental quadrature encoder measure position and direction?
Count transitions on channels A and B for relative displacement. The channel that leads identifies the direction of rotation.
What does an encoder’s index or Z pulse tell you?
It marks a repeatable reference once per revolution. A counter can reset or reload there to reference subsequent counts to that shaft position.
How do you convert encoder counts to shaft angle?
Angle = 360° × count change/effective counts per revolution. If an encoder has 100 cycles/rev and all four quadrature edges are counted, use 400 counts/rev.
How does the lab’s NTC thermistor respond when warmed?
Its resistance decreases nonlinearly as temperature rises. Whether the measured divider voltage rises or falls depends on which resistor the voltage is measured across.
What does β describe in the thermistor model?
It describes the resistance–temperature curve. In R = R₀ exp[β(1/T − 1/T₀)], use absolute temperatures in kelvins.
How does a diaphragm pressure transducer produce an electrical signal?
A pressure difference deflects a diaphragm. The sensing element converts that deflection or strain into an electrical output that can be calibrated against pressure.
Why is a piezoelectric sensor useful for detecting a tap or vibration?
A changing mechanical load produces electric charge. Charge leaks away over time, so the sensor is especially useful for rapidly changing loads.
How does an ultrasonic sensor calculate distance from echo time?
Distance = speed of sound × round-trip time/2. At 343 m/s, a 2 ms echo corresponds to 0.343 m.
What signal path did the LabVIEW sensor integration experiment use?
Beam loading strains the gage → its resistance changes → the bridge produces a differential voltage → the circuit amplifies and filters it → the DAQ digitizes it for LabVIEW.
Why balance a Wheatstone bridge before loading the beam?
Balancing brings the unloaded differential output close to zero. A later voltage change can then be related to the applied load.
Why amplify the bridge output before digitizing it?
The bridge produces a small differential voltage. Gain makes that change occupy more of the DAQ input range so the ADC can resolve smaller load changes.
How do you find the gain of an ideal noninverting or inverting op-amp?
Noninverting gain = 1 + Rf/Rg. Inverting gain = −Rf/Rin. Rf is the feedback resistor, and the minus sign indicates inversion.
What does a low-pass filter do for a slowly varying load signal?
It passes DC and low-frequency load changes while attenuating high-frequency noise. For a first-order RC filter, cutoff frequency fc = 1/(2πRC).
What does a high-pass filter do to a steady DC signal?
It attenuates low frequencies and passes higher frequencies. After the initial transient, an ideal high-pass filter gives zero output for a constant DC input.
How do band-pass and notch filters differ?
A band-pass filter passes a selected frequency band. A notch filter attenuates a narrow band, such as interference near 60 Hz.
How do you calculate the voltage resolution of an n-bit ADC?
Ideal step size ≈ input span/2ⁿ. A 10-bit ADC over 0–5 V has 1,024 levels and a step size of about 4.88 mV.
How do you connect a digital multimeter to measure voltage, current, or resistance?
Measure voltage across two points in parallel. Measure current by placing the meter in series. Measure resistance across a de-energized component, isolating it if parallel paths affect the reading.
What does each element do in a spring–mass–damper system?
The mass supplies inertia, the spring supplies a restoring force proportional to displacement, and the viscous damper supplies a force opposing velocity.
What equation describes an ideal spring–mass–damper moving freely after release?
mẍ + bẋ + kx = 0, with displacement x measured from equilibrium. The system is second order because acceleration is the highest derivative.
How do stiffness and mass affect undamped natural frequency?
ωₙ = √(k/m) in rad/s. Increasing stiffness raises natural frequency. Increasing mass lowers it. Divide by 2π to get hertz.
How do you calculate damping ratio and critical damping?
Critical damping is bcrit = 2√(km). Damping ratio is ζ = b/bcrit. It is dimensionless.
How do you distinguish undamped and underdamped free responses on a plot?
An undamped response (ζ = 0) keeps oscillating at constant amplitude. An underdamped response (0 < ζ < 1) oscillates with progressively smaller peaks.
How do critically damped and overdamped responses differ after release from rest?
Critical damping (ζ = 1) gives the fastest nonoscillatory return to equilibrium. Overdamping (ζ > 1) also prevents oscillation but gives a slower return.
Is a damping ratio of 0.707 critical damping?
No. It is underdamped. For the standard second-order step response it gives about 4.3% overshoot, making it a common engineering compromise. Critical damping is ζ = 1.
How do you obtain damped frequency from a displacement trace?
Measure time T between consecutive same-direction peaks. Then f_d = 1/T in Hz and ω_d = 2π/T in rad/s. For underdamped motion, ω_d = ωₙ√(1 − ζ²).
How can peak amplitudes reveal the damping ratio?
Measure consecutive same-direction amplitudes A₁ and A₂ from equilibrium. Logarithmic decrement δ = ln(A₁/A₂), and ζ = δ/√(4π² + δ²).
How can you isolate the damping contributed by the oil damper in Experiment IV?
Find total b = 2ζ√(km) for the setup with the damper and for the baseline setup. Subtract baseline b from total b with the damper installed.
What does an LVDT measure in the physical-response setup?
Linear displacement. Motion of its core changes the differential transformer output, allowing carriage position to be tracked over time.
What is normal strain, and what does 500 microstrain mean?
Normal strain ε = ΔL/L₀ is dimensionless. A strain of 500 µε is 500 × 10⁻⁶ = 0.0005, or 0.05% change in length.
How does a bonded metal-foil strain gage sense beam deformation?
The foil deforms with the beam surface. Tension along the grid increases its resistance, while compression decreases it.
Why does strain gage orientation matter?
A single grid primarily measures normal strain along its long grid lines. Align it with the strain direction of interest, such as the beam’s length for bending strain.
What does gage factor mean, and how do you use it?
GF = (ΔR/R₀)/ε. It converts fractional resistance change into strain. To predict resistance change, use ΔR = GF × R₀ × ε.
A 120 Ω gage with GF = 2 experiences 500 µε in tension. How much does resistance change?
ΔR = 2 × 120 × 500 × 10⁻⁶ = +0.12 Ω. This small change explains why the lab uses a bridge.
How can a dummy strain gage compensate for temperature changes?
Place an unloaded matching gage at the same temperature in an adjacent bridge arm. Similar temperature-induced resistance changes cancel to first order in the bridge output.
How are bending stress and surface strain related for a linearly elastic beam?
σ = Mc/I and ε = σ/E = Mc/(EI), where c is distance from the neutral axis. Opposite surfaces are in tension and compression.
For a cantilever with an end load, which distance do you use to predict strain at the gage?
Use the distance from the gage section to the load’s line of action. For a perpendicular force, the local bending moment is M = F × that distance.
For a rectangular beam, which dimension is cubed in I = bh³/12?
The bending depth h, measured perpendicular to the neutral axis in the bending plane. For outer-surface strain, c = h/2.
What area moment of inertia do you use for bending a circular tube?
I = π(Dₒ⁴ − Dᵢ⁴)/64 about a centroidal diameter. Use c = Dₒ/2 for the outer-surface strain.
What is Reynolds number for pipe flow, and does it have units?
Re = ρVD/μ = VD/ν, using mean velocity and actual inside diameter. It compares inertial to viscous effects and is dimensionless.
Which pipe-flow regime thresholds are given in Class 12?
Slide 569 gives laminar flow below roughly Re = 2,200–2,300 and turbulent flow above about 3,500. The intervening range is transitional.
Which flow regime has a parabolic velocity profile, and which has the flattest core?
Fully developed laminar pipe flow is parabolic, with centerline speed twice the mean. Turbulent mixing produces a flatter core. Both have zero velocity at a stationary wall.
Which flow regime generally gives better convective heat transfer, and why?
Turbulent flow under comparable conditions. Mixing transports warmer and cooler fluid between the near-wall region and the core.
Why does pressure fall along a straight, level, constant-diameter pipe carrying steady flow?
Wall shear resists motion and dissipates mechanical energy. A pressure difference is required to maintain the flow even though mean velocity stays constant.
How do you calculate mean pipe velocity from a timed collection?
Find Q = collected volume/time, then V = Q/A with A = πDᵢ²/4. Use the actual inside diameter to calculate flow area.
How do you find the Darcy friction factor in fully developed laminar pipe flow?
f = 64/Re. The Darcy friction factor is dimensionless. At Re = 1,600, f = 0.040.
What does the Moody diagram relate, and how does roughness enter?
It relates Darcy friction factor, Reynolds number, and relative roughness ε/D. In turbulent flow, greater relative roughness generally increases friction factor at the same Re.
How do you use the Darcy–Weisbach equation to predict straight-pipe loss?
Head loss h_f = f(L/D)V²/(2g). The equivalent pressure loss is Δp = ρgh_f = f(L/D)ρV²/2.
How does an elbow or valve enter a pipe-loss calculation?
Use its loss coefficient K and the appropriate reference velocity. The fitting contributes hₘ = KV²/(2g). Add fitting losses to straight-pipe losses for the total.
What does a differential pressure reading in inches of H₂O mean?
It expresses pressure as the equivalent height of a water column. Convert using Δp = ρwater g h. One inch of water is about 249 Pa.