1/42
Looks like no tags are added yet.
Impregnation
Replaces clearing agent with an embedding medium to provide tissue support for sectioning
Hardens tissue for easy cutting into thin sections using a microtome.
Purpose of Infiltration
PARAFFIN WAX INFILTRATION
Most commonly used infiltrating agent and very rapid acting.
Allows cutting of serial sections with ease.
PARAFFIN WAX INFILTRATION
Compatible with many staining procedures.
Not for fatty tissues
Prolonged
process may cause excessive shrinkage and tissue hardening
Inadequate
process may cause retention of clearing agent
Melting Point for Routine Work
56 degC
54 - 58 degC
What temp should the paraffin be if the lab is 20-24 degC?
50-54 degC
What temp should the paraffin be if the lab is 15-18 degC?
Manual Method
Requires 4 changes of wax at 15 mins interval
To keep the wax melted, placed inside the oven with temperature 55-60 degC
approximately 2-5 degC higher than wax melting point
Temp for Manual Method
Automatic Method
Requires the use of autotechnicon
Usually 2-3 changes of wax
Vacuum Method
Most rapid infiltration method. Vacuum hastens the removal of air bubbles and clearing agent from the tissue block
Infiltration under negative atmospheric pressure inside an embedding oven
Vacuum Method
Recommended for urgent biopsies, for delicate tissues such as lung, brain, connective tissues, decalcified bones, eyes, spleen and CNS
Melting point of vacuum method
56 degC
Paraplast
Mixture of highly purified paraffin and synthetic plastic polymers.
Recommended for bones and brain specimen.
Melting point of Paraplast
56-57 degC
Embeddol
Similar to paraplast but less brittle and less compressible.
Melting point of Embeddol
56-58 degC
Bioloid
Recommended for embedding eyes.
Ester Wax
Harder than paraffin and requires heavy duty type of microtome
Soluble in alcohol so it does not require clearing, only dehydration
Melting point of Ester Wax
46-48 degC
Tissue Mat
product paraffin with rubber
Carbowax
Water-soluble wax for enzyme histochemistry studies
Recommended for thicker sections
Advantage of Carbowax
it eliminates dehydration and clearing process.
Disadvantage of carbowax
tissues are difficult to float out and mount
Add soap to water or 10% polyethylene glycol 900 to promote floating out of sections
Remedy for Carbowax
CELLOIDIN INFILTRATION
A purified form of nitrocellulose that is soluble in alcohol and ether.
For specimens with large hollow cavities which tend to collapse
CELLOIDIN INFILTRATION (2)
For hard and dense tissues such as bones and teeth.
For large tissue sections of the whole embryo.
CELLOIDIN INFILTRATION (3)
Impregnation process is very slow and very volatile.
Thin sections, serial sections, and sections for photomicrography are all difficult to obtain.
Wet Celloidin
Recommended for bones, teeth, large brain sections and whole organs
Duration of Ether-Alcohol Solvent: Equal parts
12-24 hours
Duration for Thin celloidin (2-4%)
5-7 days
Duration for Medium celloidin (4-6%)
5-7 days
Duration for Thick celloidin (8-12%)
3-5 days until fully impregnated
70-80% Alcohol
Storage for Wet Celloidin
Dry Celloidin
Recommended for whole eye sections.
Same with wet celloidin method except it is strong using Gilson’s mixture
Chloroform + Cedarwood oil
Components of Gilson’s mixture
Low Viscosity Nitrocellulose (L.V.N.)
Form of celloidin soluble in equal parts ether and alcohol.
Plasticizers can be added like oleum ricini or castor oil.
Gelatin Infiltration
Rarely used except for frozen sections, histochemical, and enzyme studies.
Water soluble – will no longer require dehydration and clearing.
at leadt 25x the volume of the Tx
Volume for Gelatin Infiltration
Tx process for gelatin infiltration
2-3mm
Phenol
to prevent molds