1/35
THIS FLASH CARDS IS ABOUT [MANUF] INTRODUCTION.
Ventilation
Adequate _____ shall be provided.
Info
Equipment for adequate control over air pressure, microorganism, dust, humidity, and temperature shall be provided when appropriate for the manufacture, processing, packing, or holding of a drug product.
Air filtration systems
These systems, including pre-filters and particulate matter air filters, shall be used when appropriate on air supplies to production areas.
Recirculation of dust
If air is recirculated to production areas, measures shall be taken to control _____________ from production.
Exhaust systems
In areas where air contamination occurs during production, shall be adequate ________ or other systems adequate to control contaminants
Air-handling systems
__________ systems for the manufacture, processing, packing of penicillin shall be completely separate from those for other products for human use.
Potable Water
This water shall be supplied under continuous positive pressure in a plumbing system free of defects that could contribute contamination to any drug product.
Environment Protection Agency’s Primary Drinking Water Regulations
40 CFR part 141
Potable water shall meet the standards prescribed in the (1)___________________ set forth in (2)______________.
Engineering Department
Which department is responsible in pumbling?
Potable Water System
Water not meeting such standards shall not be permitted in the?
Drains
These shall be of adequate size and where connected directly to a sewer, shall be provided with an air break or other mechanical device to prevent back-siphonage.
International Society for Pharmaceutical Engineers (ISPE)
Clean room designations are assigned by the?
ABCD
What are the four (4) European Grade?
A
Which European grade is the ultimate clean zone (where sterile medications are stored)?
B
Which European grade is the background (?) directly surrounding grade A?
D
Which European grade is the less critical zone (ex. washing equipment).
Materials Support Area
This is constructed to withstand moisture, steam, detergents and is usually a CLASS 100,000 clean room.
Impervious materials
Materials Support Area:
Ceiling, walls and floor should be constructed of what materials?
Vinyl or epoxy-sealing coat
Materials Support Area:
Finishes with ____________ provides a continuous surface free from all other holes/crevices.
Heat and Humidity
Materials Support Area:
Should be exhausted adequately so that the ___________ will be removed for the comfort of personnel.
Sink and Counter Space
Materials Support Area:
Adequate ___________ space must be provided.
Info
Materials Support Area:
Must be cleanable and microbial load must be monitored and controlled.
Compounding Area
In this area the formula is compounded, and although it is not essential that this area must be aseptic, control of microorganisms and particulates should be more stringent than in the materials support area.
Stainless Steel
Compounding Area:
Cabinets and counters should preferably be constructed of?
Info
Compounding Area:
Fit snugly to walls and other furniture.
Materials Support Area
Compounding Area:
Ceiling, walls and floor should similar to those for the?
Dispensing Area (Defined Area)
Aseptic Area is also known as?
Microbial and Particulate Control
Aseptic Area requires construction features designed for maximum?
Info
Aseptic Area:
> Ceiling, walls, and floors must be sealed.
> All counters should be constructed of stainless steel and hung from the wall.
> Light fixtures, utility service lines and ventilation fixtures must be recessed in the walls of the ceiling.
Tanks
_____ containing the compounded product should remain outside the aseptic area.
Hose Lines
Aseptic Area:
Product fed into the area through the?
Stainless Steel Cabinet
Large mechanical equipment should be housed as possible within?
Demountable
Mechanical parts that will contact the parenteral product should be?
Airlock Room
Sterile Cover
The personnel entering the aseptic area should enter through (1)_________. They should also wear (2)_________ (ex. PPE) prior to entering.
Airlock
This is a transitional space that typically has two doors in series to separate a controlled environment (such as cleanroom, lab, operating room, or isolation room) from a corridor, or vice versa. The two doors should be interlocked to avoid being opened at the same time.
Info
Aseptic Area:
Movement within the room should be minimal and in & out movement should be restricted during filing procedure.