Chapter 33 Fluoroscopy: Image Intensifiers, Dose, and Flat-Panel Detectors

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/72

encourage image

There's no tags or description

Looks like no tags are added yet.

73 Terms

1
New cards

Who invented the fluoroscope, and when?

Thomas Edison, in 1896.

2
New cards

What is the primary purpose of fluoroscopy?

Dynamic, real-time imaging for functional studies and active diagnosis.

3
New cards

What did early fluoroscopes consist of?

An X-ray tube and hand-held fluorescent viewing screen.

4
New cards

Which body areas received high exposures with early hand-held fluoroscopes?

Eyes, neck, and hands.

5
New cards

When were image intensification tubes developed?

1948.

6
New cards

What replaced mirror optics for image-intensifier viewing?

Closed-circuit television systems.

7
New cards

By approximately what year did digital fluoroscopy predominate?

2005.

8
New cards

What matrix technology is associated with digital fluoroscopy?

Thin-film transistor (TFT) matrices.

9
New cards

Name four clinical uses of fluoroscopy.

GI studies, angiograms, line placement, and orthopedic surgery.

10
New cards

Why should fluoroscopy not be used to preview routine radiographic positioning?

It unnecessarily increases patient radiation exposure and is considered unethical by the ASRT.

11
New cards

What operating mA range is listed for fluoroscopic X-ray tubes?

0.5-5.0 mA.

12
New cards

What mA range is given for standard radiographic X-ray tubes?

50-1200 mA.

13
New cards

What is the minimum SOD for fixed fluoroscopic equipment?

15 inches (38 cm).

14
New cards

How is fluoroscopic exposure commonly activated?

Foot switch or handle switch.

15
New cards

How is the fluoroscopic field collimated?

Electronically.

16
New cards

What are the main components of an image-intensifier tube?

Input screen, photocathode, electrostatic lenses, magnification tubes, anode, and output screen.

17
New cards

What material forms the image-intensifier input phosphor on surface

Sodium-activated cesium iodide (CsI).

18
New cards

What is the input screen (phosphor) made of.

Glass, titanium, steel, or aluminum

19
New cards

What is the thickness of the input phosphor?

0.1-0.2 mm.

20
New cards

What is the input screen's primary conversion?

X-ray photons into light photons.

21
New cards

Why is the input screen curved?

So electrons from every point travel the same distance to the output screen


22
New cards

What is the traitor for the input screen being curved?

Causes pin cushion distortion (See image quality)

23
New cards

What is the photocathode's function?

It emits photoelectrons when illuminated by light from the input phosphor.

24
New cards

What metals are used in the photocathode?

Photoemissive metals: Cesium and antimony.

25
New cards

What is photoemission?

Release of electrons from the photocathode in response to light.

26
New cards

What do electrostatic lenses do?

Accelerate and focus electrons toward the anode/output screen.

27
New cards

What happens to image orientation in the image intensifier from the electrostatic lenses

It is inverted and reversed.

28
New cards

Electrostatic lenses

  • Focusing the electrons onto the small output screen is what makes ______ Possible


Minification gain (primary source of brightness gain)

29
New cards

What do the magnification tubes do?

Ad voltage

30
New cards

What does increasing voltage to electrostatic lenses do?

Increases electron acceleration and shifts the focal point away from the anode.

31
New cards

Magnification tubes are described according to what

According to the diameter of the input screen used

32
New cards

What type of tubes are used according to the diameter of the input screen used?

Dual focus

  • 23/15 cm (9”/6”)

Multi field intensifier are popular

  • Triple field (12”/9”/6”)

  • Quad Field (14”/12”/9”/6”)


33
New cards

What happens to spatial resolution in image-intensifier magnification mode?

It increases (good!)

34
New cards

What happens to patient dose in image-intensifier magnification mode?

It increases. (Bad!)

35
New cards

What is the image-intensifier magnification formula?

Magnification = input screen diameter / diameter of input screen used during magnification

36
New cards

practice

  • what is the magnification for an image viewed with an I.I tube with an input screen diameter of 9 inches that is using a 5 inch diameter area during magnification


9/5 = 1.8 times.

37
New cards

What charge does the image-intensifier anode have?

Positive.

38
New cards

What approximate anode voltage is listed?

25 kVp.

39
New cards

Why does the anode have a central opening? (Hole in center)

To allow electrons to pass to the output phosphor.

40
New cards

The output screen is a ______ Screen

Glass fluorescent

41
New cards

What phosphor material is listed for the output screen?

Zinc-cadmium sulfide.

42
New cards

What does the output screen emit when struck by electrons?

Green light.

43
New cards

some I.I tubes coat the output phosphor onto a ______ Instead of glass, which carries light directly to the camera

Fiber optic disc

44
New cards

What can replace the conventional output screen in some newer image intensifiers?

A fiber-optic disc.

45
New cards

Trace the image-intensifier conversion chain.

X-rays -> input phosphor/light -> photocathode/electrons -> focused electrons -> output phosphor/light.

46
New cards

What is total brightness gain?

A measurement of the increase of image intensity achieved by a I.I tube

47
New cards

Brightness gain of I.I tubes tend to be -

5000 to 30,000

48
New cards

What is the brightness gain formula?

Brightness gain = Minification gain x flux gain.

49
New cards

What typical brightness gain range is listed?

Approximately 5,000-30,000.

50
New cards

What causes minification gain?

Focusing electrons from a large input phosphor area onto a smaller output phosphor area.

  • input (6”/9”/12”) —→ output (1”)


51
New cards

What is the minification gain formula?

(Input screen diameter / output screen diameter)^2.

52
New cards

What is minification gain for a 6-inch input and 1-inch output?

(6/1)^2 = 36.

53
New cards

What is flux gain?

A measurement of conversion efficiency of output screen

  • Electrons in; Light out


54
New cards

If 50 light photons emerge per electron, what is flux gain?

50.

55
New cards

What is total brightness gain if minification gain is 36 and flux gain is 60?

36 x 60 = 2,160.

56
New cards

Maintaining fluoroscopic, image, brightness, and contrast does what

It maintains brightness of image by automatically changing exposure factors according to subject density/thickness

57
New cards

Maintaining fluoroscopic, image, brightness, and contrast monitors what

It monitors current flowing between the cathode and the anode of I.I tube Or intensity of output screen

58
New cards

The primary beam is changed when what happens

When current falls below established level (vary mA, kV & pulse time)

59
New cards

Maintaining fluoroscopic, image, brightness, and contrast

  • This control has a wide variety of systems and names:


  • automatic brightness control (ABC)

  • Automatic brightness stabilization (ABS)

  • AUTOMATIC DOSE CONTROL (ADC)

  • Automatic gain control (AGS)


60
New cards

The control and maintaining fluoroscopic image brightness and contrast is very important in maintaining what?

Image quality

61
New cards

Image quality

  • contrast: is controlled by:


Amplitude of video signal

62
New cards

Image quality

  • contrast is affected by:


  • scattered ionizing radiation

  • Penumbral light scatter


63
New cards

Image quality

  • resolution; varies depending on


SID, OID, minification gain

64
New cards

Image quality

  • distortion is caused by


The curved shape of the image intensifier input screen

65
New cards

Image quality

  • distortion: what is the pincushion effect


Image is stretched and warped toward the edges

66
New cards

Image quality

  • distortion: what is vignetting


Image brightness falls off toward the edges

67
New cards

Image quality

  • quantum mottle is caused by what


It is blotchy grainy appearance caused by two little exposure to input Phosphor

68
New cards

Image quality

  • Quantum mottle: what are the options to improve it?


Increase MA, Reduced distance between patient and Imogen intensifier, Increase KVP

69
New cards

What is the purpose of video viewing systems?

To convert the light from the output of the image intensifier tube to digital signal

70
New cards

What are the most common video viewing systems?

  • semiconductor (CCD or CMOS) Attached to the output, Phosphor

  • Display monitor for viewing


71
New cards

What are the components of CCD? (Charged coupled device)

  1. CCD array- convert light to electrical signal incense to computer

  2. ADC- Converts e- to digital signal


72
New cards

What are the components of CMOS (Complementary metal oxide semiconductor)

  1. CMOS sensor - Converts light to e- And send to computer

  2. ADC- Convert e- To digital Value


73
New cards

What is flat panel fluoroscopy.

Replace the image intensifier with a digital flat panel TFT detector