1/49
Comprehensive vocabulary flashcards covering power generation, grid transmission and distribution, renewable energy sources, transformer construction and cooling, AC loads, power factor, inductive reactance, and impedance calculations based on science and electrical principles notes.
Alternating Current (AC) for Transmission and Distribution
An electrical transmission system favored because voltage levels can easily be transformed up and down using transformers, thereby reducing line current for the same transmitted power, which reduces heat loss, energy loss, and installation costs.
Coal (as an Energy Source)
A conventional fossil fuel energy source characterized by a limited available supply and harmful emissions.
Oil (as an Energy Source)
A fossil fuel energy source characterized by a limited supply and the production of problematic waste gases upon combustion.
Gas (as an Energy Source)
A fossil fuel energy source with a limited supply that burns cleaner than coal or oil.
Nuclear Power
A power source that uses cheap, clean fuel with no atmospheric emissions during operation, but poses significant problems regarding nuclear waste disposal and facility decommissioning.
Thermal Power Generation Process
The power generation cycle where burnt fuel heats water in a boiler to create pressurized steam, which flows through pipes to drive the vanes of a turbine, turning a generator to produce electricity.
Substation
A utility installation housing specialist equipment, notably step-up and step-down transformers, to change voltage levels between the generation, transmission, and distribution stages.
UK Generation Voltage Level
The standard voltage level at which electricity is typically produced by commercial power station generators in the UK, namely 25kV.
UK Transmission Voltage Levels
Extra-high voltage levels used across the National Grid transmission network to transport bulk electricity over long distances, specifically 275kV and 400kV.
UK Distribution Voltage Levels
Voltage levels used to step power down safely for regional transport and final consumption, consisting of 132kV, 66kV, 33kV, 11kV, 400V (three-phase), and 230V (single-phase).
Photovoltaic (PV) Cell
Semiconductor cell arrays that convert light directly into electrical energy to produce direct current (DC) voltage, which can be sited locally where needed and requires an inverter to interface with AC systems.
Inverter
An electrical power converter required to change direct current (DC) voltage generated by photovoltaic arrays into alternating current (AC) voltage.
Wind Power
An alternative power source where moving air turns turbine blades to drive an electrical generator connected to the public supply, though generation is constrained if there is insufficient wind or excessively strong wind.
Wave Power
The extraction of kinetic energy stored in ocean waves using attenuators or floating buoys that drive hydraulic rams or hydro-electric turbines to generate electricity, which is transmitted to the grid via undersea cable.
Hydro Power
A generation method that utilizes water stored behind a dam released through conduits (penstocks) to spin a water turbine, driving an AC generator that converts mechanical energy into electrical energy before discharging the water back to the watercourse.
Penstock
A specialized pipe or conduit that directs pressurized water from a reservoir or dam intake directly to the vanes of a water turbine.
Run-of-River Hydro
A hydro scheme that diverts a portion of water from a pond, stream, or river without requiring a large dam, using the natural drop in elevation (head) to create the fluid pressure needed to drive a turbine.
Head (Hydro Power)
The natural vertical height drop of water in a hydro system that creates the hydrostatic pressure and velocity required to drive a turbine.
Pumped Storage
A hydroelectric facility featuring two reservoirs (upper and lower) where water released from the upper reservoir drives a turbine-generator system during peak demand and can be returned or pumped back during off-peak periods.
Battery Storage
An energy storage system enabling electricity to be retained for self-consumption rather than exported to the grid; notable drawbacks include high cost, large physical footprint, required recharge cycles, and limited cycle lifespan.
Star Connection (Three-Phase)
A three-phase configuration with a central neutral point, supplying two operating voltages (230V phase-to-neutral and 400V line-to-line), separated electrically by 120∘.
Phase-to-Neutral Voltage
The potential difference measured between any single phase line conductor and the star neutral conductor, standardized at 230V in the UK for domestic utility supplies.
Line-to-Line Voltage
The potential difference measured between any two phase conductors in a three-phase system, standardized at 400V in the UK.
Phase Balancing
The distribution practice of allocating neighboring single-phase consumer loads to alternating phases across the three-phase supply network to balance loading and reduce current flow through the neutral conductor.
Delta Connection
A three-phase circuit configuration where the three windings or loads are connected end-to-end in a closed loop without a neutral conductor, where line voltage equals phase voltage (VL=VP), commonly utilized for three-phase electric motors.
Step-Up Transformer
A transformer that increases voltage while reducing output current proportionally, utilized at generating stations to minimize transmission heat losses over long distances.
Step-Down Transformer
A transformer that decreases high transmission or distribution voltages down to safer, usable levels for industrial, commercial, and domestic equipment.
Air-Cooled Transformer
A dry-type transformer cooling method where operational heat is dissipated directly from the windings and core to the surrounding air, often assisted by forced fans to enhance airflow.
Oil-Cooled Transformer
A transformer cooling method where the core and windings are immersed in insulating oil that circulates through external cooling tubes or radiator fins to dissipate heat away from the unit.
Water-Cooled Transformer
A heavy-duty cooling design where water is pumped through a heat exchanger or dedicated cooling loops to extract thermal energy from the transformer oil.
Hysteresis Loss
A core power loss dissipated as heat, caused by the continuous reversal of the magnetic domains within the transformer core due to alternating current; it is reduced by using high-grade magnetic core steel.
Eddy Current Loss
A core power loss resulting from circular currents induced within the conductive core material by the alternating magnetic field; it is minimized by building the core from thin, insulated laminations of electrical steel.
Magnetic Flux Leakage
A transformer loss occurring when a portion of the magnetic flux produced by the primary winding does not link with the secondary winding; it is minimized by tight coupling of the windings and optimized core geometry.
Core-Type Transformer Construction
A transformer structural arrangement where the primary and secondary windings are wound around the outer limbs of a rectangular magnetic frame that forms a single continuous magnetic circuit.
Shell-Type Transformer Construction
A transformer structural arrangement where the magnetic core encloses the windings, with coils mounted on a central limb while two outer core limbs provide dual parallel return paths for the magnetic flux.
Mutual Inductance
The electromagnetic principle whereby an alternating current flowing through a primary coil creates an alternating magnetic field that cuts across and induces an electromotive force (EMF) into an adjacent secondary coil.
Isolating Transformer
A transformer designed to transfer electrical energy via mutual inductance without an electrical connection between input and output circuits, providing galvanic separation typically with a 1:1 turns ratio (230V in, 230V out).
Transformer Voltage and Turns Ratio Equation
The fundamental formula relating transformer primary and secondary parameters: VsVp=NsNp=IpIs, where V represents voltage, N represents number of turns, and I represents current.
Transformer Apparent Power Rating
The total capacity rating of a transformer expressed in kilovolt-amperes (kVA) or megavolt-amperes (MVA), defining maximum output current at nominal terminal voltage (Amps=VoltsVA).
Resistive Load
An electrical load (such as an electric kettle, space heater, or filament bulb) that converts real electrical energy directly into heat and light through pure conductor resistance.
Inductive Load
An electrical load containing wire coils or windings (such as electric motors, transformers, or fluorescent ballasts) that stores energy in an electromagnetic field, causing circuit current to lag behind voltage.
Unity Power Factor
The operating condition in a purely resistive AC circuit where voltage and current waveforms are completely in phase with a phase angle difference of 0∘, yielding a power factor of cos(0∘)=1.0.
Lagging Power Factor
A condition characteristic of inductive AC circuits where the current waveform peaks after the voltage waveform due to counter-EMF, resulting in a phase angle and a power factor of less than 1.0 (e.g., 0.8lagging).
I²R Loss (Copper Loss)
The electrical power dissipated as waste thermal energy in conductors, cables, or transformer windings due to conductor resistance, calculated as P=I2×R.
Inductive Reactance (X_L)
The opposition to alternating current flow caused specifically by the inductance of a coil when exposed to an AC waveform, measured in ohms (Ω) and calculated using XL=2πfL.
Inductance (L)
The electrical property of a coil or circuit that opposes any change in current through self-induced electromotive force, measured in henries (H) or millihenries (mH).
AC Active Power Formula
The mathematical equation used to calculate real, useful power consumed in an AC circuit: P=V×I×cos(θ), where V is voltage, I is current, and cos(θ) is the circuit power factor.
Consequences of Low Power Factor
Operating effects caused by a poor power factor (cos(θ)<1.0), requiring significantly higher supply current for the same useful power (I=V×cos(θ)P), which produces greater I2R heating losses, larger voltage drops along distribution cables, and necessitates oversized cables and switchgear.
Electrical Impedance (Z)
The total effective opposition to alternating current flow in a circuit containing both resistance (R) and reactance (XL), measured in ohms (Ω) and calculated using the formula Z=R2+XL2.
Impedance Triangle
A right-angled vector triangle representing an AC circuit, where the horizontal adjacent base represents resistance (R), the vertical opposite side represents reactance (X), and the hypotenuse represents total impedance (Z).