1/33
Looks like no tags are added yet.
A force plate under a walker’s foot reads 900 N, pointing up. What does that tell you about the force the foot pushes on the plate with?
It is 900 N, pointing down
A force plate measures the ground reaction force in three directions: up and down, forward and back, and side to side. During ordinary walking, which is by far the largest?
Up and down
Which of these is measured directly in a gait lab, rather than calculated from other measurements?
The ground reaction force
The lab’s software reports the knee joint moment in N·m/kg, the moment divided by the person’s mass. Why divide by mass?
So that people of different sizes can be compared
A person with a mass of 80 kg stands perfectly still with both feet on one force plate. About what does the plate read?
785 N
A person has a mass of 55 kg. About what is their body weight in pounds?
121 pounds
At midstance, the one foot on the ground carries 0.70 body weights. At . that moment the body’s center of mass is
Accelerating downward
You stand on a bathroom scale in an elevator that is going up and slowing to a stop at the top floor. While it slows, the scale reads
Less than your weight
A walker with a mass of 60 kg has one foot on a force plate and the other in the air. The plate reads 690 N. What is the vertical acceleration of their center of mass?
1.69 m/s², upward
Averaged over whole strides of steady walking, the two plates together read almost exactly the walker’s body weight. Why?
The center of mass ends every stride at the same height and vertical speed it started with, so its average vertical acceleration is zero

The figure shows the vertical force under Walker G’s left foot for one stance, in body weights. The dashed line is one body weight. At all four lettered points Walker G’s right foot is in the air. At which point is the vertical acceleration of the center of mass zero?
at which point is the center of mass accelerating upward the hardest?
Point B, Point A
Compared with someone walking fast, how does the vertical force under one foot look for someone walking very slowly?
Lower peaks and a shallower valley, the whole curve closer to one body weight
During the first half of a stance, the fore-aft ground reaction force under the foot points backward. What does that force do to the walker?
It slows down the forward motion of the walker’s center of mass
A walker with a mass of 80 kg has a braking impulse of −24 N·s in one stance. By how much does it change their forward speed?
−0.30 m/s
The fore-aft force under a foot stays at −100 N for 0.2 s. What impulse does it deliver over that time?
−20 N·s
A stance’s fore-aft force is recorded at 2000 samples a second. In R, sum(fwd[fwd < 0]) comes to −46,000 N. What is the braking impulse?
−23 N·s
The treadmill’s plates record 2000 times a second. How much time passes between one sample and the next?
0.5 ms
Just after the treadmill belt is jerked under them, a walker’s left foot lands on the right belt. What does the left belt’s plate record during that step?
Close to nothing, as if the left foot were still in the air
In class, heel ← read.csv(“left_heel.csv”) reads a file of 4,000 rows whose first line holds the names time, heel_y and plate. What is heel$heel_y?
The whole column named heel_y, all 4,000 values
In class, the heel position was made with x <- -heel$heel_y / 1000. Why the minus sign and the 1000?
The lab’s Y axis points toward the back of the treadmill, so the minus sign makes forward positive, and the 1000 turns millimeters into meters
In R,
x <- c(0.10, 0.12, 0.16, 0.18, 0.18)
dt <- 0.01
n <- length(x)
v <- (x[3:n] - x[1:(n - 2)]) / (2 * dt
What is v?
3 3 1
In class, after the central difference, we ran v <- c(NA, v, NA). Why?
So that v has one value for every sample, the same length as t, and plot(t, v) works
What is stance after stance <- v < 0 & t < 10?
A TRUE or FALSE for every sample: TRUE where the heel moves backward and the time is before 10 s
A heel velocity, in m/s, is stored as
v <- c(NA, 0.8, 0.3, -0.9, -1.1, -1.2, 0.4, 1.5, -0.2, NA)
What does which(diff(sign(v)) < 0) + 1 return?
4, 9
In class, we compared the heel contacts found from the heel’s velocity with the contacts found by the force plate. For the first 10 seconds of the trial, before the treadmill belt was jerked under the walker, every heel contact came about 40 ms before the plate’s contact. Why?
The heel reaches its furthest-forward point a moment before the foot carries enough weight for the plate to pass 50 N
In class, after plotting the heel velocity, we ran
abline(v = t[plate_strikes], lty = 3)
What does this add to the plot?
A dotted vertical line at the time of every plate contact
In R,
contacts <- c(112, 336, 561, 785)
What is contacts[-2]?
112, 561, 785
A walker’s stride times, in order, come out as 1.12, 1.11, 1.13, 0.74, 0.38, 1.12 and 1.11 s. What most likely happened?
A false contact split one stride in two
In the force code from class, with mass <- 63.5 and bw <- mass * 9.81, one sample of left is 760 N. What is that sample of left / bw?
1.22
Walker 1 has a mass of 90 kg and a first peak of 900 N. Walker 2 has a mass of 62 kg and a first peak of 750 N. Once the forces are put in body weights, which walker has the higher first peak?
Walker 2, at 1.23 body weights against 1.02
In class, after finding the landings and leavings, we ran
stopifnot(length(on) == length(off)).
What would make it stop?
A file that starts or ends with the foot on the plate, so there is a leaving with no landing, or a landing with no leaving
In class, we found the samples at which a walker’s left foot landed on the force plate (on) and left it (off). For one walker, in R,
on <- c(1000, 3240, 5480)
off <- c(2360, 4600, 6840)
fs <- 2000
What does diff(on) / fs return?
What are the two numbers that diff(on) / fs returns
1.12 1.12
stride times, in seconds
In class, after running our force code on the younger walker, we ran it again on the older
walker. Which two lines did we change?
The file name and the mass
![<p><span style="background-color: transparent;"><strong> </strong>The figure below shows Walker G’s average vertical force over one stance, mean_curve, against the percent of stance, pct. In class, we found the second peak with max(mean_curve[pct > 50]), not with max(mean_curve). Why?</span></p>](https://assets.knowt.com/user-attachments/7816895f-9cd4-496b-a04f-53e728ba8d50.png)
The figure below shows Walker G’s average vertical force over one stance, mean_curve, against the percent of stance, pct. In class, we found the second peak with max(mean_curve[pct > 50]), not with max(mean_curve). Why?
max(mean_curve) finds the highest point of the whole curve, which for this walker is the first peak