1/18
Looks like no tags are added yet.
🛬 Landing Gear Configuration
2 Main Gear × 2 wheels each. (Breaks)
1 Nose Gear × 2 wheels (steerable). (No Breaks)
Total = 6 wheels.
Hydraulic System A
Normal landing gear retraction and extension.
Nose wheel steering.
Alternate brake system.
Manual gear extension is also provided
Brake Systems
Normal Brakes
Hydraulic System B
Antiskid protection
Autobrake capability
Alternate Brakes
Hydraulic System A
Antiskid protection
NO Autobrake
Landing Gear Control
by LANDING GEAR lever.
Ground = Lever locked against UP.
In flight =Air/grnd system→Energizes (electrical) Solenoid→Lever lock Opens
Override trigger = Bypasses lock
Landing Gear Retraction
🛫 Main Gear
LANDING GEAR lever UP → Retraction begins.
Brakes stop main wheel rotation→Mechanical uplocks hold gears UP.
Rubber seals + oversized hubcaps complete outboard wheel fairing.
🛬 Nose Gear
Retracts forward.
Snubbers stop wheel rotation→Overcenter lock holds gear UP.
Doors are mechanically linked to gear.
⚙ Hydraulic Pressure
LANDING GEAR lever OFF → Removes Hydraulic pressure
⚠ Damaged Tire / Loose Tread
Loose tread impacts wheel well ring fitting:
Gear stops retracting→free-falls to DOWN
Cannot retract again until fitting is replaced
🔥 Exam focus – Important Differences
Main gear = Mechanical uplocks.
Nose gear = Overcenter lock.
Main wheel rotation = Brakes.
Nose wheel rotation = Snubbers.
Loose tread impact = Gear returns DOWN; fitting replacement required.
Landing Gear Transfer Valve
Normally, landing gear retraction uses Hydraulic System A
Hydraulic System B provides Backup hydraulic pressure through→Transfer Valve→Raise gear at normal rate.
🛫 ALL 4 Conditions Required:
Airborne.
No. 1 engine RPM below limit.
Landing Gear lever UP.
Either main gear not UP AND LOCKED.
Landing Gear Extension
LANDING GEAR lever DN → Hydraulic System A releases uplocks.
Extension is achieved by:
Hydraulic pressure.
Gravity.
Air loads.
🔒 Gear DOWN Locking
Overcenter mechanical locks.
Hydraulic locks.
🚪 Nose Wheel Doors
- Remain OPEN when gear is DOWN.
🔥 Exam focus:
System A = Releases uplocks.
Extension = Hydraulic pressure + Gravity + Air loads.
Gear fully extended = Overcenter mechanical + Hydraulic locks.
Nose wheel doors = OPEN when gear DOWN.
Manual Extension
Trigger: Loss of Hydraulic System A pressure.
Manual gear releases → Release uplocks → Gear free-falls to DOWN and LOCKED.
Extension forces:
Gravity.
Air loads.
🚪 Access Door OPEN
Manual extension = Possible with lever in ANY position.
Normal extension = Possible if System A pressure is available.
Retraction = DISABLED.
🔄 Restore Normal Retraction – 3 Steps
Access door CLOSED.
Landing Gear lever DOWN + System A pressure available.
Landing Gear lever UP.
🔥 Exam focus: With the manual extension access door OPEN, landing gear retraction is DISABLED, regardless of LANDING GEAR lever position.
Nose Wheel Steering
⚙ 1. Steering Availability
Nose wheel steering operates only when BOTH conditions are met:
Nose gear is DOWN.
Nose gear is compressed by airplane weight.
💧 2. Normal Nose Wheel Steering
Powered by Hydraulic System A.
LANDING GEAR lever DOWN makes System A pressure available to the steering metering valve.
🔄 3. Alternate Nose Wheel Steering
Powered by Hydraulic System B.
Requires ALL 3 conditions:
NOSE WHEEL STEERING switch = ALT.
Normal quantity in System B reservoir.
Airplane on the ground.
⚠ 4. Alternate Steering Failure
If a hydraulic leak occurs downstream of the Landing Gear Transfer Valve and causes loss of System B fluid in the reservoir:
A sensor detects the condition.
Landing Gear Transfer Valve closes.
Alternate nose wheel steering is lost.
🎛 5. Steering Controls
Nose Wheel Steering Wheel
- Primary steering control.
Rudder Pedals
Provide limited steering control.
Rudder pedal steering is deactivated as the nose gear strut extends.
Position Pointer
Located on the nose steering wheel assembly.
Shows nose wheel steering position relative to neutral.
🚜 6. Towing / Pushback
A lockout pin can be installed in the towing lever.
This:
Depressurizes nose wheel steering.
Allows pushback or towing.
Does NOT require depressurizing the hydraulic systems.
🔥 Exam Focus – Must Memorize
Normal steering = System A.
Alternate steering = System B.
ALT steering requires: ALT switch + Normal System B reservoir quantity + Airplane on ground.
System B fluid loss → Transfer valve closes → Alternate steering lost.
Steering wheel = Primary control.
Rudder pedals = Limited control.
Towing lockout pin = Depressurizes steering without depressurizing hydraulic systems.
Brake System
🛑 1. Brake Configuration
Each main landing gear wheel has a multi-disc hydraulic-powered brake.
Total of 4 braked wheels (2 on each main gear).
Nose wheels have NO brakes.
Brake pedals provide independent control of LEFT and RIGHT brakes.
💧 2. Normal Brake System
- Powered by Hydraulic System B.
💧 3. Alternate Brake System
Powered by Hydraulic System A.
If Hydraulic System B pressure is LOW or System B fails, System A automatically supplies pressure to the alternate brake system.
🔥 Exam Focus – Must Memorize
Main gear wheels = Multi-disc hydraulic brakes.
Nose wheels = NO brakes.
Brake pedals = Independent LEFT / RIGHT control.
Normal brakes = System B.
Alternate brakes = System A.
System B low/failure → System A automatically supplies alternate brake pressure
Brake Accumulator
🔋 1. Hydraulic Power
- Brake accumulator is pressurized by Hydraulic System B.
🛑 2. Emergency Brake Capability
If BOTH normal and alternate brake system pressure are lost, trapped hydraulic pressure in the brake accumulator remains available.
It can provide:
Several braking applications.
Parking brake application.
🔥 Exam Focus – Must Memorize
Accumulator charging source = Hydraulic System B.
Both normal and alternate brake pressure LOST → Accumulator provides backup pressure.
Remaining capability = Several brake applications OR parking brake application.
💡 Remember: The brake accumulator retains trapped hydraulic pressure, allowing limited braking even after both brake systems lose pressure.
Antiskid Protection
🛑 1. Antiskid Availability
Antiskid protection is provided in BOTH normal and alternate brake systems.
Available even with loss of BOTH hydraulic systems.
⚙ 2. Normal Brake System – Individual Wheel Protection
Each main gear wheel has individual antiskid protection.
When a skid is detected, the associated antiskid valve reduces brake pressure until the skidding stops.
⚙ 3. Alternate Brake System – Wheel Pair Protection
Works similarly to the normal system.
Antiskid protection is applied to main gear wheel pairs, instead of individual wheels.
🛡 4. Protection Types
Both normal and alternate brake systems provide four types of protection:
Skid Protection: Detects skidding and reduces brake pressure.
Locked Wheel Protection: Protects against wheel locking.
Touchdown Protection: Provides protection during touchdown.
Hydroplane Protection: Provides protection against hydroplaning.
🔥 Exam Focus – Must Memorize
Normal Brakes:
Hydraulic System B.
Individual wheel antiskid protection.
Alternate Brakes:
Hydraulic System A.
Wheel-pair antiskid protection.
Both Systems:
Skid protection.
Locked wheel protection.
Touchdown protection.
Hydroplane protection.
Very important
Antiskid remains available even after loss of BOTH hydraulic systems.
Autobrake System
🛑 1. Hydraulic Power
Uses Hydraulic System B pressure.
Operates ONLY when the Normal Brake System is functioning.
🛫 2. Rejected Takeoff (RTO)
- Provides maximum deceleration during a rejected takeoff.
🛬 3. Landing Operation
Provides automatic braking immediately after touchdown.
Uses preselected deceleration rates.
🛡 4. Antiskid Protection
- Antiskid protection remains available during autobrake operation.
🔥 Exam Focus – Must Memorize
Hydraulic power = System B.
RTO = Maximum deceleration.
Landing = Automatic braking immediately after touchdown at preselected deceleration rates.
Autobrake works ONLY with the Normal Brake System functioning.
Antiskid protection = YES during autobrake operation.
💡 Remember: Autobrake = System B + Normal Brakes + RTO maximum deceleration / Landing preselected deceleration + Antiskid protection.
Rejected Takeoff (RTO)
🛫 1. RTO Selection
RTO mode can be selected ONLY on the ground.
When selected, AUTO BRAKE DISARM light illuminates AMBER 🟠 for 1–2 seconds, then extinguishes.
This indicates successful completion of the automatic self-test.
⚙ 2. RTO Arming Conditions
ALL 5 conditions must exist:
Airplane on the ground.
Antiskid and autobrake systems operational.
AUTO BRAKE select switch = RTO.
Wheel speed less than 60 knots.
Forward thrust levers = IDLE.
🛑 3. Rejected Takeoff – Below 88 Knots
If takeoff is rejected before wheel speed reaches 88 knots:
Automatic braking is NOT initiated.
AUTO BRAKE DISARM light does NOT illuminate.
RTO autobrake function remains ARMED.
🛑 4. Rejected Takeoff – At or Above 88 Knots
If takeoff is rejected after reaching 88 knots:
Forward thrust levers are retarded to IDLE.
Maximum braking is applied automatically.
✈ 5. Automatic RTO Disarming
RTO mode automatically disarms when BOTH air/ground systems indicate AIR mode.
AUTO BRAKE DISARM light does NOT illuminate.
AUTO BRAKE select switch remains in RTO.
🔄 6. Manual Reset / Disarming
To reset or manually disarm the autobrake system:
- Position AUTO BRAKE select switch to OFF.
⚠ 7. Landing with RTO Still Selected
If landing occurs with RTO selected, without cycling the AUTO BRAKE select switch through OFF:
No automatic braking action occurs.
AUTO BRAKE DISARM light illuminates AMBER 🟠 2 seconds after touchdown.
🔥 Exam Focus – Must Memorize
RTO Selection
Ground ONLY.
Self-test: DISARM light 🟠 ON for 1–2 seconds, then OFF.
Arming Speed
- Below 60 knots = Required for arming.
Rejected Takeoff
Below 88 knots = NO automatic braking; RTO remains armed.
At/above 88 knots = Thrust levers IDLE → Maximum automatic braking.
Automatic Disarming
Both air/ground systems indicate AIR → RTO automatically disarms.
DISARM light remains OFF.
Selector remains at RTO.
Landing with RTO Selected
No automatic braking.
DISARM light 🟠 illuminates 2 seconds after touchdown.
💡 Key numbers: 60 kt = Arming limit | 88 kt = Braking activation threshold | 1–2 sec = Self-test | 2 sec = Landing warning.
Landing Autobrake
Self-test: Failure → AUTO BRAKE DISARM light AMBER 🟠 → Autobrake NOT armed.
4 landing deceleration settings. On dry runways, maximum autobrake deceleration is less than full pedal braking.
Braking activation – BOTH required:
Thrust levers → IDLE
Main wheels → Spin-up
Selection after touchdown: Allowed above 30 kt. If both activation conditions are met → braking starts immediately.
During braking:
Spoilers / thrust reversers contribute → Autobrake pressure decreases.
Selector rotated → Deceleration setting changes without disarming.
Continues to complete stop unless pilot terminates braking.
Autobrake Disarm
Selector to OFF → Autobrake disarmed. AUTO BRAKE DISARM light remains OFF.
After braking starts, any of these actions immediately disarm autobrake and illuminate AUTO BRAKE DISARM light AMBER 🟠:
SPEED BRAKE lever → DOWN detent.
Forward thrust lever(s) → Advanced.
Exception: first 3 seconds after touchdown during landing.
Manual brakes → Applied.
Parking Brake
Hydraulic pressure: Parking brake operates with either System A or B pressurized. If both are unpressurized → brake accumulator maintains pressure. Check accumulator pressure on the HYD BRAKE PRESS indicator.
Setting the parking brake:
Depress both brake pedals fully.
Pull PARKING BRAKE lever UP simultaneously.
→ Pedals mechanically latched down + parking brake valve closes.
Releasing: Depress both pedals → PARKING BRAKE lever releases.
Fault: May illuminate ANTISKID INOP light AMBER 🟠.
Takeoff with parking brake set:
Either forward thrust lever advanced → Takeoff configuration warning horn sounds.
With SB YK982: TAKEOFF CONFIG lights also illuminate.
Air/Ground System
Controls airplane systems according to GROUND or AIR operation.
Sensors: 6 air/ground sensors — 2 on each landing gear.
Sensor signals → Air/ground logic → Configure airplane systems for the appropriate AIR or GROUND status.
Air/Ground Logic
System | ✈ AIR | 🛬 GROUND |
|---|---|---|
🚪 Exit Locks | Engage: N2 > 50% + 3 doors closed | Release: thrust lever < 53° |
❄ Packs | One pack → HIGH (flaps UP) | HIGH only: APU bleed + engine bleeds OFF |
🌬 Pressurization | Programmed AUTO | High power only |
🌪 Ram Air | Fans ON | Fans ON + deflectors extended |
🪽 Wing Anti-Ice | Valves OPEN | Cycle OPEN/CLOSED; switch trips OFF at lift-off |
🎚 Autothrottle | Go-around below 2,000 ft RA | Takeoff mode; disengages 2 sec after landing |
🛫 TO/GA | Go-around mode | Takeoff mode |
📡 ACARS | Strut extension = Takeoff | Strut compression = Landing |
🎙 Voice Recorder | Erasure prevented | Erasure allowed + parking brake set |
⚙ Engine Idle | Flight idle | Ground idle |
🔄 Thrust Reverser | Disabled | Enabled |
🔥 APU Fire Horn | Wheel-well horn OFF | Wheel-well horn ON |
🧯 Cargo Fire | 2nd bottle timer ON | 2nd bottle timer OFF |
🛑 Speed Brake | Armed for landing | Deploys if armed; RTO available |
🪽 Auto Slat | Enabled (flaps 1–25) | Disabled |
📼 Flight Recorder | Electrical power | Electrical power + either engine running |
🧭 FMC Position | GPS / DME / VOR-DME | GPS only |
💧 Standby Pump | Flaps extended + A/B pressure lost | Automatic above 60 kt |
🛞 Antiskid | Touchdown protection | Normal braking after wheel spin-up |
🛑 Autobrake | Landing mode | RTO; landing selection above 30 kt |
🔒 Gear Lever Lock | Released | Latched |
💧 Gear Transfer Valve | Enabled | Disabled |
⚠ Stall Warning | Enabled | Disabled |
🚨 Takeoff Warning | Disabled | Enabled |
🔥 Numbers to Memorize
50% N2 – Exit door locks.
53° – Exit door lock release.
2,000 ft RA – Go-around enable.
2 sec – Autothrottle disengagement after landing.
60 kt – Standby hydraulic pump ground operation.
30 kt – Landing autobrake selection after touchdown.