SYSTEMS FINAL ALL

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/521

encourage image

There's no tags or description

Looks like no tags are added yet.

522 Terms

1
New cards

Why is air conditioning used?

- Conditions cabin air

- Comfortable environment

- Applies temperature, humidity and ventilation control

2
New cards

Where is the pressurised air from for temperature control?

- From engine compressors

- Needs to be cooled a bit by air-con packs

3
New cards

How much is air is engine bleed air?

50% since air is recirculated so less engine bleed air is needed

4
New cards

How is the temperature of air from air-con packs determined?

By the zone requiring the coldest air temperature (aircraft has separate zones)

5
New cards

How is do other zones receive warmer air?

Trim air system adds hot air to adjust temperature

6
New cards

What is the purpose of an air con pack?

- Dry, sterile, dust free conditioned air at proper temperature, flow rate and pressure

- To satisfy pressurisation and temperature requirements

- Refrigeration system

7
New cards

What are the two types of refrigeration systems?

- Air-cycle refrigeration system

- Vapour-cycle refrigeration system

8
New cards

What are the components of an air-cycle system?

- Aka bootstrap system

- One or more air-to-air heat exchangers

- Compressor and turbine

- May have cooling fan (blows air through primary and secondary heat exchangers if no ram air)

- Refrigeration bypass valve

- Shutoff valve

9
New cards

How does an air-cycle system work?

- Hot bleed air goes through primary heat exchanger (cools)

- Goes through compressor (heats back up) and again through secondary heat exchanger (cools)

- Then goes through turbine and cools further

- Goes through water separator

- Gets mixed with other bleed air by temperature controller (like trim air system)

10
New cards

Why is a compressor needed in the air-cycle system?

To work the turbine

11
New cards

Why is there a water separator in the air-cycle system?

Cold air holds water that will condense, centrifugal force water separator and coalescing bag removes that water

12
New cards

What is the purpose of a vernatherm in the air-cycle system?

Detects when temperature gets too cold and there could be ice, commands warm air to heat up air (bypassing turbine)

13
New cards

What is the vapour-cycle system?

- Refrigerant in a closed circuit

- Warm cabin air flows past evaporator and is cooled

- Biggest temperature drop across thermal expansion valve (liquid turns to gas)

14
New cards

How does the vapour-cycle system work?

- Refrigerant boils at very low temperature

- Gas goes through compressor, pressurised, becomes liquid

- Increases in heat once compressed

- High pressure vapour through condenser

- Pump sucks air through expansion valve

- Liquid turned to gas from pressure differential as pump sucks gas

15
New cards

How is oxygen provided in aircraft?

Pressurisation gives oxygen at the right pressure, supplementary oxygen for emergencies

16
New cards

What is diluter demand?

- Regulated gaseous oxygen

- Generally for crew

- Diluted with air below 34000ft

- Responds to inwards breath

- Prolongs supply

17
New cards

What are oxygen masks for pax like?

Simple flexible rubber

18
New cards

What are oxygen masks for crew like?

More fitting, can have microphone and headset as well, may also be a smoke mask

19
New cards

Who generally needs a walk around gaseous oxygen bottle and why?

Crew, in the cabin to help assist pax and perform other required duties

20
New cards

How can charged oxygen be stored?

- Liquid (LOX)

- Gas

21
New cards

What is continuous flow oxygen?

Chemical candle, gaseous for pax cabin providing automatic, immediate and continuous oxygen

22
New cards

What are the pros of the chemical candle?

- Lightweight

- Less equipment

- Less maintenance

23
New cards

What are the cons of the chemical candle?

- Higher fire hazard

- Not tamperproof

- Won't turn off

24
New cards

How are chemical candles started?

Mechanically by pulling down on string and releasing firing pin or electrically activated

25
New cards

Why is oxygen dangerous?

Supports combustion (fire hazard)

26
New cards

What can't you do when charging (with oxygen)?

- No pax on board

- No refuelling

- No power on

27
New cards

Why should you never fully deplete a gas bottle?

Atmospheric moisture can enter the bottle and cause internal corrosion

28
New cards

Why are cabins pressurised?

- Not enough oxygen pressure at the more efficient altitudes to fly at

- Safe and comfortable for pax and crew

29
New cards

What will the max altitude of an aircraft generally be determined by?

Max allowable pressure differential (difference between internal and ambient pressures)

30
New cards

How is a cabin pressurised?

Supplying more air to cabin than is required and controlling the excess air that's leaving (constant supply balanced against variable rate of outflow air)

31
New cards

What is the max allowable PD in general?

- Light aircraft 3-5 psi

- Large piston aircraft 5.5 psi

- Jet transport aircraft 9 psi

32
New cards

What happens to pressurisation of an aircraft during its life cycle?

- The higher it flies, the higher the PD

- Pressurisation, then stretching, eventually fatigued and stretched until strain hardening then potentially cracking

- Limited to a number of cycles

- Can fly lower after that (less strain)

33
New cards

How can an aircraft be pressurised?

- Superchargers

- Turbochargers

- Engine-driven air pumps

- Bleed air from gas turbine compressors

34
New cards

What's the downside to using engines for pressurisation?

Places large demands on engine so loss of power and must filter out oil or fumes

35
New cards

How does the supercharger provide air for pressurisation?

Air goes through intake and half the compressor (driven by the engine) goes to the engine, half to cabin for pressurisation

36
New cards

How does the turbocharger provide air for pressurisation?

Air goes through intake and half the compressor (driven by exhaust gases) goes to the engine, half to cabin for pressurisation

37
New cards

How does an engine-driven air pump provide air for pressurisation?

Roots blower on the back of a gearbox, lobes trap and move pressurised air from inlet to outlet

38
New cards

How does bleed air from a turbine provide air for pressurisation?

Bleed air from engine compressor (can drive a turbo-compressor) or used through a jet pump flow multiplier

39
New cards

What is a cabin pressure regulator?

An outflow valve, controlling the escape of excess air so the aircraft is set at a desirable altitude

40
New cards

What is a positive pressure relief valve?

Prevents over-pressurisation, opens automatically at a predetermined pressure. Set on the ground as the maximum allowable pressure differential

41
New cards

What is a negative pressure relief valve?

A vacuum, preventing cabin pressure going below the ambient air

42
New cards

What is a dump valve?

Dumps residual cabin pressure on landing, controlled by WOW switch and can be selected by pilots in an emergency

43
New cards

What is the isobaric range?

Controls cabin pressure to a selected value/constant cabin pressure altitude during various levels of flight by changing the cabin pressure differential

44
New cards

What is the differential range?

Limits cabin pressure to a preset differential value/limits to a maximum permissible value

45
New cards

How will a regulator reference changing altitude during flight?

It keeps the selected altitude, adjusting the pressure to keep it the same but if max differential pressure is exceeded, a safety valve will open to lower cabin pressure

46
New cards

What are the general components of a cabin pressure regulator?

- Outflow valve

- Differential control

- Isobaric control

- Dump valve

47
New cards

What is the rate of change of cabin pressure when ascending or descending?

Ascending = 0.26 psi

Descending = 0.16 psi

48
New cards

What is catching the cabin?

Cabin can't exceed aircraft altitude otherwise PD becomes negative so the negative pressure safety valve gets pushed open and outside air flows into the cabin. Cabin altitude will then descend with the aircraft

49
New cards

What are the malfunctions that can come with pressurisation?

Decompression and negative pressure

50
New cards

What happens when there is negative pressure?

An object will compress

51
New cards

What happens when there is explosive decompression?

Cabin pressure changes faster than lungs can decompress, generally less than 0.5 seconds, likely to have lung damage

52
New cards

What happens when there is rapid decompression?

Cabin pressure changes but lungs can decompress faster, not likely to get lung damage

53
New cards

What happens when there is slow decompression?

Automatic visual and aural warnings are installed so crew don't become incapacitated before it's detected, however is is more dangerous than rapid decompression

54
New cards

What will happen to the pressurisation in an emergency?

There is an emergency pressurisation mode, directing a mixture of bleed air and ram air into the cabin, when combined with fully closed outflow valves, can preserve some pressurisation of the aircraft

55
New cards

Where are fire protection systems built-in to aircraft?

In designated fire zones and potential fire zones

56
New cards

What are the requirements for a fire detection system?

- Warns immediately of fire/over heat

- Red light and audible signal

- Indicates extinguished fire

- Indicates re-ignition of fire

- Shows location

- Durable and resistant to damage

- Auto re-sets when fire is extinguished

57
New cards

When would smoke and toxic gas detection be used?

When type of fire anticipated is expected to produce more smoke before sufficient temperature change

58
New cards

What will a smoke and toxic gas detection system be?

Generally in cargo/baggage hold and lavatory

- Light refraction type (photoelectric cell)

- Ionisation type

- Solid-state type

59
New cards

What is the light refraction type of smoke detector?

Smoke interferes with light beams and reflects it into a lens and photocell which sets off alarm

60
New cards

What is the ionisation type smoke detector?

Ions align creating a circuit with electricity from battery. As smoke particles enter alarm, ion path is broken up and weakens circuit, setting off alarm

61
New cards

Where would detection systems typically be located?

- Powerplant

- Cargo hold

- APU

- Lavatory

62
New cards

What are the three systems for fire detection?

Thermo-switch

Thermocouple

Tubular type

- Fenwal

- Kidde

- Pneumatic type (Systron-donner)

- Lindberg system

63
New cards

What is a thermo-switch system?

Aka a spot detector, a circuit with one or more thermal switches connecting in parallel. Outer casing expands with heat (bimetallic design) and elongates, the two contacts inside then meet and close the circuit activating the warning system. Will reset itself

64
New cards

What is a thermocouple system?

Two dissimilar metals with one end fused together, placed in an open frame, as airflows over the probe, the exposed wires at one end create a hot junction and the other end is under insulating material which creates a cold junction. The temperature difference creates a current which sets off a sensitive relay. If temperature rise is slow, cold junction heats up along with the hot junction

65
New cards

What is a fenwal system?

Continuous loop, small, lightweight, flexible inconel tube, pure nickel wire centre conductor, space between conductor and tubing wall has ceramic insulating material and eutectic salt packing which has a low melting point. When heated, current flows between the wire and the tube wall (salt melts and drops resistance) which signals control unit. Will correct itself once the fire is out

66
New cards

What is a kidde system?

Continuous loop system, inconel tube with thermistor material embedded with two electrical conductors. When heated, thermistor drops resistance, sensed by electronic control circuit monitoring system (wire conductors). Second wire is the grounding wire, grounded to outer shell

67
New cards

What is the pneumatic system (systron-donner)?

Very similar to Lindberg pneumatic fire detection system

Continuous-length system, stainless steel tube with two separate gases and a gas absorption material (wire). Tube will normally have helium gas under pressure. Titanium centre wire has hydrogen gas, wrapped in helical shape. Gaps between turns release hydrogen gas under certain temperatures and once corrected, titanium reabsorbs hydrogen. Constant volume means pressure increases with temperature (helium gas in tube exerts more pressure and closes pneumatic switch)

68
New cards

What is the role of fire extinguishing agents?

- Displaces oxygen (CO2/dry powder)

- Chemically combines with oxygen to prevent combustion

69
New cards

Why aren't dry chemical extinguishers used?

They cause damage by toxic and corrosive chemicals

70
New cards

What are the two types of airframe fire extinguishing systems?

- Conventional (older)

- High Rate of Discharge System (HRD System)

71
New cards

How does a conventional fire extinguishing system work?

Perforated ring and distributor nozzle, when activated, agent bottles are opened and gas flows through lines to selected engine, flowing out of the perforated ring to smother fire

72
New cards

What is an HRD system?

Spherical bottles under high pressure, actuated by explosive charges (squibs) to flood compartment and displace oxygen. Propels extinguishing agent at high speeds

73
New cards

How does an HRD system work?

Fire switch closed by crew member. Explosive charge (squib) at neck of bottle is detonated and a cutter driven through sealing disk in neck, instantly releasing extinguishing agent to area selected

74
New cards

How do you determine thermal discharge on an airframe extinguishing system?

Gauge on bottle visible through window on the outside of the aircraft, red blow-out disk or yellow disk being displaced indicates bottle cartridge has fired (red due to over heat or over pressure). When thermal discharge occurs, pressure in line blows out disk

75
New cards

Why are large aircraft primary flight controls often split?

To lower control authority and provide redundancy

76
New cards

What is done to flight controls to prevent damage (specifically wing warping)?

The amount they travel can be reduced with speed or with ailerons, out ailerons are locked at high speed

77
New cards

What is it called when the flight control is the whole of the surface?

All-flying tailplanes, all moving wingtips and all moving fins

78
New cards

What are the types of secondary flight controls?

- Trim tabs

- Balance tabs

- Servo tabs

- Anti-servo tabs

- Spring tabs

- Variable incidence tailplanes

79
New cards

What is the purpose of a trim tab?

Trims the controls via trim wheel in the cockpit, holding controls in the desired position

80
New cards

What is the purpose of a balance tab?

Reduces control loads (aids control)

81
New cards

What is the purpose of a servo tab?

Assists movement (manually connected to control stick)

82
New cards

What is the purpose of anti-servo tabs?

Increases control feel making it more difficult to move the controls

83
New cards

What is the purpose of spring tabs?

Like a servo tab but the spring varies the load

84
New cards

What are the auxiliary controls?

- Spoilers (can be part of primary flight controls)

- Speed brakes

85
New cards

What are high lift devices?

- Flaps

- Slats

- Slots

- Leading edge flaps (Kruger, droop)

86
New cards

How are primary flight controls mainly mechanically actuated?

- Push-pull control rod system

- Cable and pulley system

- Combination of the above

87
New cards

What helps the pilot to move the flight controls?

- Aerodynamic balancing and/or tabs

- Power actuators (hydraulic jacks) either power assisted or power operated

88
New cards

What are power assisted controls?

- Still have direct mechanical link

- As pilot's control moves, control surface moves and pilot/spool valve directs hydraulic fluid to an actuator

- Actuator assists moving control

- Valve resets to a neutral/locked position

89
New cards

How will shockwaves affect the control system for power assisted?

Causes buffeting which is fed back through the control system

90
New cards

How do power operated controls work?

Pilot control directly linked to actuator control valve. Actuator provides all effort needed. Pilot has no actual feel of control forces, it requires artificial feel

91
New cards

What is a power control unit (PCU)?

A pilot/spool valve and actuator incorporated together

92
New cards

What happens if there is a complete hydraulic failure?

Hopefully emergency hydraulic systems are available, but if not, differential engine control

93
New cards

What is a fly-by-wire system?

Pilot controls/movements transmitted (with synchro's or digital data bus) electronically to actuators. Like a power operated system but incorporates control valves to direct fluid to actuators (uses a feedback system)

94
New cards

What is artificial feel?

"q" feel system, based off existing dynamic pressure. Computer calculates forces based on control surface position and airspeed, uses hydraulic pressure to oppose pilot movements

95
New cards

What is actuator gust snubbing (gust locks)?

Large aircraft can't fit external control locks so they have internal control column locks or a gust suppression system fitted in the control actuator. The flight control is free to move but won't hit the primary stop with force (causing damage)

96
New cards

What is the take-off configuration warning system?

An audible warning if the aircraft isn't configured for take-off and the thrust levers are advanced to take-off. It uses position sensors and the thrust management computers

97
New cards

When will a stall warning typically go off?

Warning of approach stall, the margin is typically 5% above the stall airspeed

98
New cards

How does the stall warning work?

Stick shaker, stick pusher and audible warnings only cancelled when AoA if reduced

99
New cards

What is the pitch limit indicator (PLI)?

Estimates the aircraft pitch at which the stick shaker will operate

100
New cards

What are the inputs for the stall warning?

- N1/EPR (Engine power)

- AoA

- WOW switch

- ADC