1/39
Comprehensive practice flashcards covering basic fabrication techniques, marking out, mechanical cutting, forming, materials, joining methods, hand tools, and workshop power equipment.
What are the five levels of the hierarchy of risk control in order from most preferred to least preferred?

What is the difference between a red-and-black 'DANGER' tag and a yellow-and-black 'OUT OF SERVICE' tag?
A red-and-black 'DANGER' tag is designed for individual personal protection and must only be removed by the person named on it. A yellow-and-black 'OUT OF SERVICE' tag is placed on damaged or faulty equipment to prevent operation and accidents until repairs are complete.
What action is required when an activity receives a 'High' risk score on a risk assessment matrix?
An action plan is required, and senior management approval must be obtained before commencing the task.
Why must an operator never wear both ear plugs and ear muffs at the same time in a noisy workshop?
Wearing both simultaneously muffles all sound completely, preventing the worker from hearing necessary verbal communication or emergency alarms.
What formula is used to calculate the optimum drill spindle speed (RPM) for a metal drilling operation?
RPM=ÏĂdCutting speedĂ1000â
Where cutting speed is measured in m/min and d is the diameter of the drill bit in mm.
According to the drilling cutting speed table, what is the recommended cutting speed for mild steel?
24m/min.
What formula is used to calculate the tapping size drill (T.S.D.) for an ISO metric thread?
T.S.D.=Major Diameter (MD)âPitch (P).

How is the hypotenuse (c) of a right-angled triangle calculated using Pythagoras' theorem when given sides a and b?
a2+b2=c2, which rearranges to c=a2+b2â.
How does the sliding end hook of a steel measuring tape maintain accuracy for both internal and external measurements?
The end hook is riveted with slight play that shifts by an amount equal to the thickness of the hook blade, automatically compensating for inside and outside measurements.

What are the three interchangeable heads that can be mounted to the graduated steel rule of a combination set?
What are the two primary uses of the centre head in a combination set?
What is the primary function of a trammel in sheet metal layout?
It acts as a large-scale compass or divider for scribing arcs, circles, or radii that are too large to be scribed with standard dividers.
How should a guillotine's rated mild steel cutting capacity be adjusted when shearing stainless steel sheet?
Halve the machine's stated mild steel shearing capacity (for example, a guillotine rated for 6mm mild steel can only shear up to 3mm stainless steel).
What are the four primary cutting actions used in fabrication cutting machinery?
How does the cutting mechanism of a power nibbler differ from that of a power shear?
A shear cuts with a scissor-like shearing action without removing material, whereas a nibbler punches out a continuous slot in the metal, ejecting waste cuttings called 'slugs'.
How does the cutting action of a cold cut saw differ from an abrasive cut-off saw?
A cold cut saw cuts with a chip-forming milling action using a toothed, circular high-speed steel blade lubricated with coolant, whereas an abrasive saw uses a high-speed abrasive friction disc that grinds through metal without producing standard chips.
What feature makes a pan brake more versatile than a conventional cornice brake for folding sheet metal?
The pan brake features removable, segmented clamping jaws (fingers) of varying widths that allow complete four-sided boxes or pans to be folded without distorting existing bends.
What is the general rule for the minimum cylinder diameter that can be rolled on a three-roll forming machine?
The minimum diameter that can be rolled is 1.5 to 2Â times the diameter of the roll around which the material is being formed.
What metallurgical property provides stainless steel with its corrosion resistance?
It contains a minimum of 10.5% to 11% chromium by mass, which reacts with oxygen to form an invisible, self-healing passivation layer of chromium(III) oxide (Cr2âO3â) that seals the steel from moisture and air.
What is 'galling' in stainless steel threaded fasteners, and how is it prevented?
Galling is the friction-induced tearing and cold welding of mating threads when stainless nuts and bolts are tightened together. It is prevented by using dissimilar metals (such as bronze with stainless steel) or different grades of stainless steel.
What is the primary difference in surface finish and application between Galvabond and Zincanneal sheet steels?
Galvabond is hot-dip zinc-coated with a characteristic spangled surface pattern used for general ducting and tanks. Zincanneal undergoes post-galvanising heat treatment to produce an iron-zinc alloy with a matte grey finish suitable for direct painting without primer.
What are the minimum standards for edge distance and pitch distance when installing solid rivets?
The edge distance must be at least 2Ărivet shank diameter, and the pitch distance between rivet centres must be at least 3Ărivet shank diameter.
What material allowance is required when forming a beaded (false wired) rolled edge on sheet metal?
2.5Â times the diameter of the rolled edge.
What material allowance is required when forming a wired edge on sheet metal up to 1mm thick?
2.5Â times the diameter of the wire.

Based on handle colour coding, what cutting directions are performed by these aviation tin snips?
Green handles indicate right-cutting aviation snips (cutting in a curve to the right), while red handles indicate left-cutting aviation snips (cutting in a curve to the left).
Why should an operator always pull rather than push a spanner when tightening or loosening fasteners?
Pulling allows better muscle control and balance, preventing hand and knuckle impact injuries against sharp machinery should the spanner slip or the fastener suddenly break loose.
What is the purpose of the offset shank on a double-ended ring spanner?
It raises the handle above the fastener plane to provide knuckle clearance and prevent hand injury during turning.
Why must a Phillips screwdriver never be used in a Pozidriv screw head recess?
Pozidriv screw recesses have parallel-walled ribs and a deeper recess without the taper of a Phillips design. Using a Phillips driver causes cam-out, stripping the recess and rounding the driver tip.
What is 'mushrooming' on cold chisels and punches, and why is it dangerous?
Mushrooming is the flattening and flaring of burred metal around the struck head from repeated hammer blows. When struck, these brittle burrs can fracture and fly off at high speed, causing serious eye or bodily injury.
What are the recommended cold chisel cutting angles for mild steel and cast iron?
Mild steel: 60â to 70â. Cast iron: 70â to 80â (Average general-purpose angle is 65â).
What are the hazards of using a hand file without a handle?
If the file catches or strikes an obstruction on the forward stroke, the sharp, pointed tang can be driven into the palm or wrist, causing puncture wounds.

What is draw filing, and when is it used?
Draw filing is a finishing technique where the file is held with both hands across the workpiece at right angles to its length and moved forward with light pressure to produce an ultra-smooth, uniform surface with all file marks parallel.

What is meant by the 'set' of a hacksaw blade's teeth?
The alternate sideways bending of the teeth so that the resulting slot (kerf) cut in the metal is wider than the blade thickness, preventing binding and allowing chip clearance.
Which tooth pitch hacksaw blade is recommended for cutting thin-walled tubing and sheet metal less than 3mm thick?
0.8mm pitch (32TPI).

What are the maximum allowable clearances for the tool rest and the tongue guard on a pedestal or bench grinder?
The tool rest must be set to within 3mm of the grinding wheel face, and the tongue guard must maintain a maximum wheel exposure gap of 6mm.
How long must a newly mounted abrasive grinding wheel be run at operating speed before use?
Run the new wheel at full operating speed for at least 1minute while standing to one side.
What is the difference between an orbital sander and a random orbital sander?
An orbital sander vibrates solely in tiny circular orbits, whereas a random orbital sander oscillates in a circle and moves back and forth simultaneously, preventing swirl scratches on the workpiece.

What are the standard geometric angles required for off-hand sharpening of a general-purpose twist drill bit?
An included point angle of 118â (59â per lip), a lip clearance angle of 8â to 12â, and a chisel edge angle of approximately 45â relative to the cutting lips.
What is the operational difference between a woodworking jointer and a thickness planer?
A jointer flattens a warped or twisted board face and straightens/squares edges, whereas a thickness planer machines the opposing face parallel to make the board a consistent thickness from end to end.
What is the functional difference between a jig and a fixture in machining operations?
A jig guides the cutting tool during an operation (such as a drill jig guiding a twist drill), whereas a fixture locates and secures the workpiece to the machine bed without guiding the cutting tool.