1/199
pa double check kung tama yung terms -
End suction pump
A single suction pump having its suction nozzle on the opposite side of the casing from the stuffing box and having the face of the suction nozzle perpendicular to the longitudinal axis of the shaft.
Horizontal pump
A pump with the shaft normally in a horizontal position.
In line pump
A centrifugal pump whose drive unit is supported by the pump having its suction and discharge flanges on approximately the same center
Horizontal split case pump
A centrifugal pump characterized by a housing which is split parallel to the shaft
Vertical shaft turbine pump
A centrifugal pump with one or more impellers discharging into one or more bowls and a vertical educator or column pipe used to connect the bowls to the discharge head on which the pump driver is mounted
Booster pump
A pump that takes suction from a public service main or private use water system for the purpose of increasing the effective water pressure
Horizontal split case pump
A vertical turbine pump with the pump and motor closed coupled and design to be installed underground, as in the case of a deepwell pump
Aquifer
An underground formation that contains sufficient saturated permeable material to yield significant quantities of water
Wet pit
A timber, concrete or masonry enclosure having a screened inlet kept partially filled with water by an open body of water such as pond, lake, or streams
Ground water
Water which is available from a well, driven into water bearing subsurface strata(aquifer)
Static water level
The level with respect to the pump, of the body of water from which it takes suction when the pump is not in operation
Pumping water level
The level with respect to the pump, of the body of water from which it takes suction when the pump is in operation
Drawdown
The vertical difference between the pumping water level and static water level
Impeller
Imparts velocity to the liquid, resulting from centrifugal force as the impeller is rotated
Casing
A means of throttling the leakage which would otherwise occur at the point of entry of the shaft into the casing
Shaft sleeve
Protect the shaft where it passes through the stuffing box
Wearing rings
Keeps internal recirculation down to a minimum
Bearings
Accurately locate shaft and carry radical and thrust loads
Frame
Which of the ff is used to mount unit rigidly and support bearings
Coupling
Connect the pump to the driver
Packing
The most common means of throttling the leakage between the inside and outside of the casing
Gland
To position and adjust the packing pressure
Seal gage
Provides passage to distribute the sealing medium uniformly around the portion of the shaft that passes through the stuffing box also known as water seal of lantern ring
Mechanical seal
Provides a mechanical sealing arrangement that takes the place of the packing
Rotary pumps
A positive displacement pump consisting of a fixed casing containing gears, cams, screws, vanes, plungers or similar elements actuated by rotation of the drive shaft
Reciprocating pumps
A positive displacement unit wherein the pumping action is accomplished by the forward and backward movement of a piston or plunger inside a cylinder usually provided with valves
Cam and piston pump
A type of rotary pump, consist of an eccentrically bored cam rotated by a shaft concentric in a cylindrically bored casing, with an aburment or follower so arranged that with each rotation of the drive shaft a positive quantity of liquid is displaced from the space between the cam and the pump casing
Gear pump
A type of rotary pump, consists of two or more gears, operating in closely fitted casing so arranged that when the gear teeth unmesh on one side liquid fills the space between the gear teeth and is carried around in the tooth space to the opposite side and displaced as the teeth mesh again
Screw pump
A type of rotary pump, consists of two or three screw rotors so arranged that as the rotors turn liquid fills the shape between the screw threads and is displaced axially as the rotor threads mesh
Vane pump
A type of rotary pump, consists of one rotor in a casing machined eccentrically to the dive shaft. The rotor is fitted with a series of vanes, blades or buckets which follow the bore of the casing thereby displacing the liquid with each revolution of the drive shaft
Direct acting steam pump
A type of reciprocating pump having a steam cylinder with no lap on valves, a water cylinder and a common piston rod
Crank and flywheel reciprocating pump
A type of reciprocating pump driven by compound, cross compound, or triple expansion steam engines
Power driven pump
A type of reciprocating pump that receives its forward and backward motion of the piston and plunger from the rotary motion of a revolving crankshaft by means of a crank connecting rod
Plunger pump
A type of deep well pump which are refinement of the old hand pump that have played such an important role in country home and small town water supply from wells
Turbine pump
A type of deep well pump that represent the application of vertical centrifugal pump to deep well service and are build for heads up to 305 meters and fro capacities up to 26,495 liters per minute
Ejector centrifugal pump
A type mo deep well pump that has come into wide use for small capacities combines a single stage centrifugal pump at the top of the well and an ejector or jet located own in the water
Air lift
A type of deep well pump wherein compressed air is admitted to the well to lift water to the surface, for successful operation of the system, the discharge pipe must have its lower end submerged in the well water
Heat loss from the surface is minimized
One of the reasons for insulating the pipe is:
Kirchhoff’s law
The rate of radiant energy, that is emitted by a surface at any temperature and in small wavelengths is found from the known rate of energy, that under the same conditions will be emitted from a black surface, by multiplying with the absorptivity. The above enunciation is called
Optical pyrometer
Which of the ff is generally used to measure the temperature inside the furnace?
Temperature difference between the bodies
All heat transfer processes :
Physical property of the material
What is thermal diffusivity?
M2/hr
Which of the ff is a unit of thermal diffusivity?
Wood
Non-isotropic conductivity is shown by which of the ff?
All of the above
For glass wool thermal conductivity changes from sample to sample due to changes in:
W/m K
Which of the ff is the SI unit of thermal conductivity?
0.7
What is the value of the Prandt’l number for air?
All bodies above absolute zero emit radiation
According to prevost theory of heat exchange
All of the above
Thermal conductivity of wood depends on which of the ff?
Warm in winter
A fur coat on an animal will help the animal remain to:
Reynolds number
The nature of flow of a fluid inside a tube, whether it is turbulent of laminar, can be ascertained by:
Radiation
By which of the ff modes of heat transfer is the Stefan-Boltzmann law applicable?
Zero
At all wave lengths and temperatures the monochromatic emissivity of white body is equal to:
All of the above
The radiation from flames is having
Kirchhoff’s law
The statement that the emissivity and absorptivity of a surface is surrounded by its own temperature are the same for both monochromatic and total radiation is called:
Source
A reservoir that supplies energy in the form of heat is called
Flow of hot and cold fluids alternately over a surface
In regenerator type heat exchanger, heat transfer occurs by:
Liquid metals
Least value of Prandt’l number can be expected in case of
Dubring’s rule
The boiling point of a solution is linear function of water at the same pressure, the above statement is called
Avoid deformation of tubes because of thermal expansion
Floating head are provided in heat exchangers to
Nucleation
What do you call the 1st stage of crystal formation
Condition when the change in temperature of one steam is numerically equal to the average of driving force
In heat exchanger design , one transfer unit implies:
Turbulent region
Dritus Boelter equation can be applied in case of fluids flowing in:
Long vertical tube evaporators
In sugar mills can just is evaporated in:
Single pass on shell side and double pass on tube side
A 1-2 heat exchanger refers which of the ff?
Cross flow heat exchanger
A correction of LMTD is essential in case of:
Butyl acetate
Which of the ff is used as entrainer in acetic acid-water separation?
Beta radiation
A type of radiation consisting of singly charged particles that generate to intermediate distances
Ion
An electrically charge atom or radical which carries electricity through an electrolyte is called:
Thermal energy
The energy of a body that can be transmitted in the form of heat
Change in internal energy
In an isometric process, the heat transferred is equal to:
Absorbent
A substance that is able to absorb liquids or gases and is used for removing them from a given medium or region
Kirchhoff’s law
Radiant heat transfer is described by:
Sink
A reservoir that absorbs energy in the form of heat is called
Zero
When the entire heat exchanger is selected as control volume, heat becomes
Decreasing temperature
Heat is conducted in the direction of:
Internal heat generation
The heat transfer term in the 1st law of thermodynamics may be due to any of the following except:
Radiation
All heat transfer processes require a medium of energy exchange except:
Fourier’s law
Thermal conduction is described by:
Newton’s law
Convection is described by which of the ff laws?
Kirchoff’s law
Radiation heat transfer is described by:
Kirchoff’s law
The equivalent of ratio of emissive power to absorptivity for bodies in thermal equilibrium is described by:
The logarithmic mean temperature difference
The temperature potential between temperature at the two ends of a heat exchanger are given by:
Transfer heat from one fluid to another
The function of heat exchanger is to:
Exchange heat to increase energy to the flow
The function of a superheater is to:
Cycle
What is the series of processes that eventually bring the system back to its original condition?
Black body
A theoretical body which when heated to incandescene would emit a continuous light-ray spectrum
Heat loss from the surface is minimized
Which of the ff is the reason for insulating the pipes?
Convection
Heat transfer due to density differential
Number of ions produces per mass of air x coulombs per kg
The term “exposure” in radiological effects is used as a measure of a gammas ray or an x-ray field in the surface of an exposed object, since this radiation produces ionization of the air surrounding the object, the exposure is obtained as
Conduction
The passing of heat energy from molecule to molecule through a substance
Heat rays
The radiant heat transfer depends on:
Deaerator
What kind of heat exchanger where water is heated to a point that dissolved gases are liberated?
Convection
Heat transfer processes which include a change of phase of a fluid are consider
Convection
A hot block is cooled by blowing cool air over its top surface. The heat that is first transferred to the air layer close to the block is by conduction. It is eventually carried away from the surface by
Radiation
A body that is hot compared to its surroundings illuminates more energy than its receives, while its surrounding absorbs more energy than they give. The heat is transferred from one to another by energy wave motion. What is this mode of heat transfer?
Convection
What is the heat transfer due to density differential?
Conduction
What do you call the passing of heat energy from molecule to molecule through a substance
Convection
Transmission of heat from one place to another by fluid circulation between the spots of different temperatures is called
Water
Which of the ff requires the greatest amount of heat per kilogram for a given increase in temperature?