1/123
Looks like no tags are added yet.
How does a dual axial-flow compressor improve the efficiency of a turbojet engine?
The velocity of the air entering the combustion chamber is increased.
Higher compression ratios can be obtained.
More turbine wheels can be used
Higher compression ratios can be obtained.
When the leading edge of a first-stage turbine blade is found to have stress rupture cracks, which of the following should be suspected?
Overspeed condition
Faulty cooling shield
Overtemperature condition
Overtemperature condition
Standard sea level pressure is
29.92" Hg
29.00" Hg
29.29" Hg
29.92" Hg
The procedure for removing the accumulation of dirt deposits on compressor blades is called
The soak method.
The purging process.
Field cleaning
Field cleaning
The non-rotating axial-flow compressor airfoils in an aircraft gas turbine engine, are called
Stator vanes
Rotor blades
Disc rims
Stator vanes
A gas turbine engine comprises which three main sections?
Turbine, compressor, and combustion.
Turbine, combustion, and stator.
Compressor, diffuser, and stator.
Turbine, compressor, and combustion.
The exhaust section of a turbine engine is designed to
Increase temperature, therefore increasing velocity.
Impart a high exit velocity to the exhaust gases.
Decrease temperature, therefore decreasing pressure.
Impart a high exit velocity to the exhaust gases.
When starting a turbine engine, a hung start is indicated if the engine
N1 is normal, but N2 is low.
Exhaust gas temperature exceeds specified limits.
Fails to reach idle RPM.
Fails to reach idle RPM.
The stators in the turbine section of a gas turbine engine
Decrease the velocity of the gas flow.
Increase the velocity of the gas flow.
Increase the pressure of the gas flow.
Increase the velocity of the gas flow.
Three types of turbine blades are
Impulse, reaction, and impulse-reaction.
Reaction, converging, and diverging.
Impulse, vector, and impulse-vector.
Impulse, reaction, and impulse-reaction.
Newton's Law of Motion, generally termed the "Law of Momentum," states:
Every body persists in its state of rest, or of motion in a straight line, unless acted upon by some outside force.
For every action there is an equal and opposite reaction.
Acceleration is produced when a force acts on a mass. The greater the mass, the greater the amount of force needed.
Acceleration is produced when a force acts on a mass. The greater the mass, the greater the amount of force needed.
Which of the following factors affect the thermal efficiency of a turbine engine?
1. Turbine inlet temperature.
2. Compression ratio.
3. Ambient temperature.
4. Speed of the aircraft.
5. Turbine and compressor efficiency.
6. Altitude of the aircraft.
1, 2, 5
1, 2, 3.
2, 5, 6.
1, 2, 5
Using standard atmospheric conditions, the standard sea level temperature is
59°C
59°F
29°C
59°F
The blending of blades and vanes in a turbine engine
May sometimes be accomplished with the engine installed, ordinarily using power tools.
Is usually accomplished only at engine overhaul.
Should be performed parallel to the length of the blade using smooth contours to minimize stress points.
Should be performed parallel to the length of the blade using smooth contours to minimize stress points.
In the dual axial-flow or twin spool compressor system, the first stage turbine drives the
N(2) compressor
N(1) compressor
N(1) and N(2) compressors
N(2) compressor
What type of igniter plug is used in the low tension ignition system of an aircraft turbofan engine?
Low voltage, high amperage glow plug
Self-ionizing or shunted-gap type plug
Recessed surface gap plug
Self-ionizing or shunted-gap type plug
What is the primary factor which controls the pressure ratio of an axial-flow compressor?
Compressor inlet temperature
Compressor inlet pressure
Number of stages in the compressor
Number of stages in the compressor
Where is the highest gas pressure in a turbojet engine?
At the outlet of the tailpipe section.
At the entrance of the turbine section.
In the entrance of the burner section.
In the entrance of the burner section.
An advantage of the axial-flow compressor is its
Low starting power requirements
Low weight
High peak efficiency
High peak efficiency
When starting a turbine engine,
An excessively lean mixture is likely to cause a hot start.
Release the starter switch as soon as indication of light-off occurs.
A hot start is indicated if the exhaust gas temperature exceeds specified limits.
A hot start is indicated if the exhaust gas temperature exceeds specified limits.
(1) In a turbine engine axial-flow compressor, each consecutive pair of rotor and stator blades constitutes a pressure stage.
(2) In a turbine engine axial-flow compressor, the number of rows of stages is determined by the amount of air and total pressure rise required.
Regarding these statements,
Only No. 2 is true.
Only No. 1 is true.
Both No. 1 and No. 2 are true
Both No. 1 and No. 2 are true
What is the function of the inlet guide vane assembly on an axial-flow compressor?
Converts velocity energy into pressure energy.
Directs the air into the first stage rotor blades at the proper angle.
Converts pressure energy into velocity energy.
Directs the air into the first stage rotor blades at the proper angle.
Why do some turbine engines have more than one turbine wheel attached to a single shaft?
To facilitate balancing of the turbine assembly.
To extract more power from the exhaust gases than a single wheel can absorb.
To help stabilize the pressure between the compressor and the turbine.
To extract more power from the exhaust gases than a single wheel can absorb.
Newton's First Law of Motion, generally termed the Law of Inertia, states
Force is proportional to the product of mass and acceleration.
To every action there is an equal and opposite reaction.
Every body persists in its state of rest, or of motion in a straight line, unless acted upon by some outside force
Every body persists in its state of rest, or of motion in a straight line, unless acted upon by some outside force
What is the function of the stator vane assembly at the discharge end of a typical axial-flow compressor?
To direct the flow of gases into the combustion chambers.
To increase air swirling motion into the combustion chambers.
To straighten airflow to eliminate turbulence.
To straighten airflow to eliminate turbulence.
Stator blades in the compressor section of an axial-flow turbine engine
Increase the air velocity and prevent swirling.
Decrease the air velocity and prevent swirling.
Straighten the airflow and accelerate it.
Decrease the air velocity and prevent swirling.
Where aircraft turbine blades are subjected to excessive heat stress, what type of failure would you expect?
Torsion and tension
Stress rupture
Bending and torsion
Stress rupture
An advantage of the centrifugal-flow compressor is its high
Ram efficiency
Peak efficiency
Pressure rise per stage
Pressure rise per stage
The basic gas turbine engine is divided into two main sections: the cold section and the hot section.
(1) The cold section includes the engine inlet, compressor, and turbine sections.
(2) The hot section includes the combustor, diffuser, and exhaust sections.
Regarding the above statements,
Only No. 1 is true.
Neither No. 1 nor No. 2 is true.
Only No. 2 is true.
Neither No. 1 nor No. 2 is true.
What is the first engine instrument indication of a successful start of a turbine engine?
A rise in oil pressure.
A rise in engine RPM.
A rise in the exhaust gas temperature.
A rise in the exhaust gas temperature.
Hot section inspections for many modern turbine engines are required
On a time or cycle basis.
Only at engine overhaul.
Only when an overtemperature or overspeed has occurred
On a time or cycle basis.
A standard technique used to help prevent jet engine characteristic compressor stalls during periods of engine acceleration is to
bleed a portion of the compressor air into the atmosphere.
decrease the fuel flow.
increase the velocity of the fuel being injected into the combustion chamber.
bleed a portion of the compressor air into the atmosphere.
A gas turbine engine comprises which of the following principal components?
Compressor, combustion chamber, and stator.
Compressor, combustion chamber, and turbine.
Compressor, impeller, and turbine.
Compressor, combustion chamber, and turbine.
Anti-icing of jet engine air inlets is commonly accomplished by
piping bleed air from the compressor to the inlet guide vanes and inlet cowl.
electrical heating elements located within the inlet cowl.
electrical heating elements inside the inlet guide vanes.
piping bleed air from the compressor to the inlet guide vanes and inlet cowl.
Generally, absolute pressure is
gauge pressure plus atmospheric pressure.
atmospheric pressure minus gauge pressure.
gauge pressure minus atmospheric pressure.
gauge pressure plus atmospheric pressure.
What is the function of the diffuser section?
To decrease velocity and increase pressure.
To increase velocity and increase pressure.
To decrease velocity and decrease pressure.
To decrease velocity and increase pressure.
The pressure of subsonic air as it flows through a converged nozzle
Increases
Remains constant
Decreases
Decreases
Which turbine engine compressor offers the greatest advantages for both starting flexibility and improved high-altitude performance?
Single-spool, axial-flow
Split-spool, axial-flow
Dual-stage, centrifugal-flow
Split-spool, axial-flow
A purpose of the shrouds on the turbine blades of an axial-flow engine is to
Reduce air entrance.
Increase tip speed.
Reduce vibration.
Reduce vibration.
Which of the following types of combustion sections are used in aircraft turbine engines?
Can, multiple-can, and variable.
Multiple-can, annular, and can-annular.
Annular, variable, and cascade vane.
Multiple-can, annular, and can-annular.
Severe rubbing of turbine engine compressor blades will usually cause
Cracking
Galling
Bowing
Galling
What is the possible cause when a turbine engine indicates no change in power setting parameters, but oil temperature is high?
Turbine damage and/or loss of turbine efficiency.
Engine main bearing distress.
High scavenge pump oil flow.
Engine main bearing distress.
The compressor stators in a gas turbine engine act as diffusers to
Increase the velocity of the gas flow.
Increase the velocity and decrease the pressure of the gas.
Decrease the velocity of the gas flow.
Decrease the velocity of the gas flow.
The diffuser section of a jet engine is located between
Station No. 7 and station No. 8.
The burner section and the turbine section.
The compressor section and the burner section.
The compressor section and the burner section.
What is meant by a shrouded turbine?
The turbine wheel has a shroud or band which provides cooling air to the turbine blades.
The turbine wheel is enclosed by a protective shroud to contain the blades in case of failure.
The turbine blades are shaped so that their ends form a band or shroud.
The turbine blades are shaped so that their ends form a band or shroud.
What type of turbine blade is most commonly used in aircraft jet engines?
Reaction
Impulse
Impulse-reaction
Impulse-reaction
At what stage in a turbine engine are gas pressures the greatest?
Compressor inlet
Compressor outlet
Turbine outlet
Compressor outlet
Compressor stall is caused by
A high angle of attack airflow through the first stages of compression.
A low angle of attack airflow through the first stages of compression.
Rapid engine deceleration.
A high angle of attack airflow through the first stages of compression.
What is one purpose of the stator blades in the compressor section of a turbine engine?
Stabilize the pressure of the airflow.
Control the direction of the airflow.
Increase the velocity of the airflow.
Control the direction of the airflow.
Who establishes mandatory replacement times for critical components of turbine engines?
The component manufacturer.
The FAA.
The engine manufacturer.
The engine manufacturer.
The velocity of supersonic air as it flows through a divergent nozzle
Increases
Decreases
Is inversely proportional to the temperature
Increases
The pressure of supersonic air as it flows through a divergent nozzle
Increases
Remains constant
Decreases
Decreases
Anti-icing of jet engine air inlets is commonly accomplished by
Electrical heating elements inside the inlet cowl.
Engine bleed air ducted through the critical areas.
Liquid chemical spray or deicing fluid.
Engine bleed air ducted through the critical areas.
Generally, when turbine engines are logged, the parameter used to measure thrust performance is:
1. EPR
2. N1
3. Torque
3
1 or 2
1 or 3
1 or 2
What is the primary function of the engine oil system?
To provide high-pressure hydraulic fluid for engine controls.
To lubricate and cool the engine bearings.
To prevent ice formation on the inlet guide vanes.
To lubricate and cool the engine bearings.
What type of oil is typically used in modern aircraft turbine engines?
Mineral-based oil.
Synthetic oil.
Vegetable-based oil.
Synthetic oil.
Turbine blades are generally more susceptible to operating damage than compressor blades because of
The high probability of carbon deposits.
Less exposure to solution during engine pressure wash.
Exposure to high temperatures.
Exposure to high temperatures.
A condition known as 'hot streaking' in turbine engines is caused by
A misaligned combustion liner.
Excessive fuel flow.
A partially clogged fuel nozzle.
A partially clogged fuel nozzle.
What is the purpose of the diffuser section in a turbine engine?
To increase pressure and reduce velocity.
To convert pressure to velocity.
To reduce pressure and increase velocity.
To increase pressure and reduce velocity.
(1) Accumulation of contaminants in the compressor of a turbojet engine reduces aerodynamic efficiency of the blades.
(2) Two common methods for removing dirt deposits from turbojet engine compressor blades are a fluid wash and an abrasive grit blast.
Regarding the above statements,
Only No. 2 is true.
Only No. 1 is true.
Both No. 1 and No. 2 are true.
Both No. 1 and No. 2 are true.
The fan rotational speed of a dual axial compressor forward fan engine is the same as the
Low-pressure compressor
Forward turbine wheel
High-pressure compressor
Low-pressure compressor
Some high-volume turboprop and turbojet engines are equipped with two-spool or split compressors. When these engines are operated at high altitudes, the
Low-pressure rotor will increase in speed as the compressor load decreases in the lower density air.
Low-pressure rotor will decrease in speed as the compressor load decreases in the lower density air.
Throttle must be retarded to prevent overspeeding of the high-pressure rotor due to the lower density of air.
Low-pressure rotor will increase in speed as the compressor load decreases in the lower density air.
Jet engine turbine blades removed for detailed inspection must be reinstalled in
A specified slot 90 degrees away in the direction of rotation.
The same slot.
A specified slot 180 degrees away.
The same slot.
The compression ratio of an axial-flow compressor is a function of the
Number of compressor stages
Rotor diameter
Air inlet velocity
Number of compressor stages
Which of the following may be used to accomplish internal inspection of an assembled turbine engine?
Infrared photography
Ultrasound
Borescope
Fluorescent penetrant and ultraviolet light
1, 2, 3
1, 3
3
3
Turbine nozzle diaphragms located on the upstream side of each turbine wheel are used in the gas turbine engine to
Decrease the velocity of the heated gases flowing past this point.
Increase the velocity of the heated gases flowing past this point.
Direct the flow of gases parallel to the vertical line of the turbine blades.
Increase the velocity of the heated gases flowing past this point.
A cool-off period prior to shutdown of a turbine engine is accomplished in order to
Allow the turbine wheel to cool before the case contracts around it.
Prevent seizure of the engine bearings.
Prevent vapor lock in the fuel control and/or fuel lines.
Allow the turbine wheel to cool before the case contracts around it.
What is meant by a double entry centrifugal compressor?
A compressor that has two intakes.
A compressor with vanes on both sides of the impeller.
A two-stage compressor independently connected to the main shaft.
A compressor with vanes on both sides of the impeller.
The turbine section of a jet engine
Utilizes heat energy to expand and accelerate the incoming gas flow.
Drives the compressor section.
Increases air velocity to generate thrust forces.
Drives the compressor section.
The function of the exhaust cone assembly of a turbine engine is to
Straighten and collect the exhaust gases into a solid exhaust jet.
Collect the exhaust gases and act as a noise suppressor.
Twist and collect the exhaust gases into a single exhaust jet.
Straighten and collect the exhaust gases into a solid exhaust jet.
A turbine engine hot section is particularly susceptible to which kind of damage?
Cracking
Elongation
Erosion
Cracking
Which two elements make up the axial-flow compressor assembly?
Rotor and stator
Stator and diffuser
Compressor and manifold
Rotor and stator
The stator vanes in an axial-flow compressor
Convert pressure energy into velocity energy.
Direct air into the first-stage rotor blades at the proper angle.
Convert velocity energy into pressure energy.
Convert velocity energy into pressure energy.
The highest heat-to-metal contact in a jet engine is the
Burner cans
Turbine inlet guide vanes
Turbine blades
Turbine inlet guide vanes
The two types of centrifugal compressor impellers are
Single entry and double entry
Rotor and stator
Impeller and diffuser
Single entry and double entry
Decrease in the pitch of the tail rotor will result to
The helicopter gains forward speed automatically.
The helicopter yaws opposite the direction of main rotor torque.
The helicopter yaws toward the direction of main rotor torque.
The helicopter yaws toward the direction of main rotor torque.
In a turbine engine with a dual-spool compressor, the low speed compressor
Always turns at the same speed as the high speed compressor.
Seeks its own best operating speed.
Is connected directly to the high speed compressor.
Seeks its own best operating speed.
Who establishes the recommended operating time between overhauls (TBO) of a turbine engine used in general aviation?
TBO does not apply to turbine engines.
Engine manufacturer
Aircraft manufacturer
Engine manufacturer
Turbine engine components exposed to high temperatures generally may NOT be marked with
Layout dye
Commercial felt tip marker
Wax or grease pencil
Chalk
Graphite lead pencil
3 and 5
4 and 5
1, 2, and 3
3 and 5
If, during inspection at engine overhaul, ball or roller bearings are found to have magnetism but otherwise have no defects, they
Are more acceptable service conditions.
Cannot be used again.
Must be demagnetized before use.
Must be demagnetized before use.
In a gas turbine engine, combustion occurs at a constant
Volume
Density
Pressure
Pressure
If a turbine engine is unable to reach takeoff EPR before its EGT limit is reached, this is an indication that the
Compressor may be contaminated or damaged.
EGT controller is out of adjustment.
Fuel control must be replaced.
Compressor may be contaminated or damaged.
Which of the following acts as a diffuser in a turbine engine and converts velocity to pressure?
Impeller
Manifold
Stator
Stator
The velocity of subsonic air as it flows through a convergent nozzle
Remains constant
Decrease
Increases
Increases
One function of the nozzle diaphragm in a turbine engine is to
Direct the flow of gases to strike the turbine blades at the desired angle.
Decrease the velocity of exhaust gases.
Center the fuel spray in the combustion chamber.
Direct the flow of gases to strike the turbine blades at the desired angle.
Which of the following is the ultimate limiting factor of turbine engine operation?
Compressor inlet air temperature
Turbine inlet temperature
Burner-can pressure
Turbine inlet temperature
The compression ratio of an axial-flow compressor is a function of the
Number of compressor stages.
Rotor diameter.
Air velocity.
Number of compressor stages.
Which of the following is a primary factor in determining the stage compression ratio of an axial-flow compressor?
Rotor blade airfoil shape.
Compressor inlet pressure.
Number of stages.
Rotor blade airfoil shape.
The velocity of supersonic air as it flows through a divergent nozzle
Increases
Decreases
Remains constant
Increases
The pressure of supersonic air as it flows through a divergent nozzle
Increases
Decreases
Remains constant
Decreases
Anti-icing of jet engine air inlets is commonly accomplished by
Routing engine bleed air through the inlet, locker sections, and inlet guide vanes.
Electrical heating elements inside the inlet cowl.
An alcohol spray system.
Routing engine bleed air through the inlet, locker sections, and inlet guide vanes.
Which statements are true regarding aircraft engine propulsion?
An engine-driven propeller imparts a relatively small amount of acceleration to a large mass of air.
Turbojet and turbofan engines impart a relatively large amount of acceleration to a smaller mass of air.
In modern turboprop engines, nearly 50% of the exhaust gas energy is extracted by turbines to drive the propeller and compressor with the rest providing exhaust thrust.
1, 2
1, 3
1, 2, 3
1, 2
An exhaust cone placed aft of the turbine in a jet engine will cause the pressure in the first part of the exhaust duct to
Increase and the velocity to decrease.
Decrease and the velocity to increase.
Increase and the velocity to increase.
Increase and the velocity to decrease.
In a dual axial-flow compressor, the first stage turbine drives
N(1) compressor
Low pressure compressor
N(2) compressor
N(2) compressor
Main bearing oil seals used with turbine engines are usually what type(s)?
Labyrinth and/or silicone rubber
Labyrinth and/or carbon rubbing
Teflon and synthetic rubber
Labyrinth and/or carbon rubbing
In what section of a turbojet engine is the jet nozzle located?
Combustion
Turbine
Exhaust
Exhaust
Some engine manufacturers of twin-spool gas turbine engines identify turbine discharge pressure in their maintenance manuals as
Pt2
Pt7
Tt7
Pt7
Which of the following engine variables is the most critical during turbine engine operation?
Turbine inlet temperature
Compressor inlet air temperature
Compressor RPM
Turbine inlet temperature
What is the primary advantage of an axial-flow compressor over a centrifugal compressor?
Greater pressure ratio
High frontal area
Less expensive
Greater pressure ratio
The purpose of a bleed valve, located in the beginning stages of the compressor, in an aircraft gas turbine engine is to
Control excessively high RPM to prevent a compressor stall.
Vent some of the air overboard to prevent a compressor stall.
Vent high gas air pressure overboard to prevent a compressor stall.
Vent some of the air overboard to prevent a compressor stall.