1/36
Looks like no tags are added yet.
forging
multi-step plastic deformation by compressive forces applied through dies (can be hot or cold work)
isothermal forging
when dies are heated to the same temperature as material
small
desirable (surface area / volume) ratio
forging strength to weight ratio compared to casting or machined parts
up to 20% higher
why is forging strength to weight ratio higher than casting or machined parts?
due to cold work (strain hardening), element porosity and improved grain structures
how much of starting material is lost from flash?
20-40%
flash
material flowed/pushed outward that fills gap between non-closed platens, to be cut off later
post-forging process
finishing (usually)
forging is usually preformed at…
elevated temperatures (hot work)
uses of forging
shape workpiece to near-net shape
improve microstructure
directional grain flow
eliminate porosity
die, equipment, and labor costs
high (big and expensive), high operator skills
forgeability
extent to which a material can be shaped without cracking
as temperature increases for forgeability…
forgeability increases
when are heated dies used?
when a material has limited forgeability
upsetting test
(open die forging) compression test, vary strain rate and temperature to find optimal forging conditions
hot twist test
(torsion) torsion until failure, twisting as much as possible to hot piece, vary temperature and strain rate, measure most turns before failure (optimal forging temperature)
ways to differentiate types of forging processes
die configuration
tolerance
classes of die configuration
a. open
b. impression
c. closed
types of tolerancing
a. blocker forging
b. conventional forging
c. precision; flash-less, near-net shape
open-die forging
for simple shapes to continue to further processing, i.e. hammer and anvil
homogeneous deformation
created by flat, open-dies, under ideal conditions
barreling
when the top and bottom diameters are less than the center diameterc
causes of barreling
friction
opposes outward motion of fie surface
reduced by lubricant or ultrasonic vibration of platens(dies)
cold platens(dies) on hot worked piece
as temp inc, yield strength inc, ductility dec
reduced by heating dies (isothermal forging) or insulating lubricant
what happens if dies are too hot during forging?
lowers strength
can damage dies
can lose dimensional tolerance
impression-die forging
uses shaped dies to form a part with specific geometry, dimensionally better, platens move together— forging the part to take shape of the cavity
impression-dies
dies are never closed completely
benefits of flash (impression forging)
helps fill fie cavity because it will have high pressure and friction, at elevated temps it cools quickly (acts like plug)
forces in impression-die forging
each location within workpiece is subjected to different strains, strain rates and temperatures— therefore, strength will not be uniform due to varying levels of cold work (leads to residual stress)
closed-die forging
forging without flash, think: coins
volume MUST be exact
what happens if volume is oversized? (closed-die forging)
premature die failure, can jam machine, can break parts of press
what happens if volume is undersized? (closed-die forging)
material will not fill die completely, leaves pockets and holes
before closed-die forging, the material…
has previous in-house work
must have correct volume, porosity, and material properties
closed-die forging drawbacks
wear on dies
parts need to be replaced more frequently
most expensive dies
problems with variability in starting material
has to be carefully controlled, thus operator costs tend to be very expensive
benefits of closed-die forging
parts require little-to-no machining
very fine surface finish
blocker forging
“roughing out a shape”
moves material to other location(s), produces parts that are far from final dimensions, inexpensive dies (don’t have to be machined to tight tolerances)
conventional forging
usually after blocker forging, moves material into another shape closer to final dimensions
precision forging
special dies machined to very high accuracy, part is formed very close to final dimensions, more expensive— but for large batches, these costs can be offset by the reduced requirement for post-machining