1/30
Flashcards covering biomass energy principles, wood thermochemical and biochemical conversion pathways, biofuels properties, and Philippine renewable energy policy.
What proportion of global primary energy is supplied by biomass, and where does it rank among global energy sources?
Biomass is the world's 4th-largest energy source, accounting for about 10–14% of global primary energy.
What is the typical elemental composition of wood fuel by weight?
Wood is approximately 50% carbon, 44% oxygen, and 6% hydrogen by weight, with very low ash and no sulfur.
How do the heating value and volatile fraction of wood compare to those of coal?
Wood has a heating value of about two-thirds of coal and a volatile content of approximately 80%, compared to only 20–30% in coal.
What does the term recalcitrance refer to in biomass processing?
Recalcitrance refers to the natural resistance of wood to being broken down due to the combination of cellulose, hemicellulose, and lignin, requiring strong pretreatment.
What are the primary thermal decomposition products released when wood is heated?
Water vapor (driven off initially around 275∘C), non-condensable gases (CO, CO2, H2, CH4), bio-oil pyrolysis vapors (methanol, acetone, acetic acid, hydrocarbons, tars), and charcoal (carbon-rich solid residue).
What visual cue indicates that air vents should be sealed during charcoal production?
Air vents are sealed when the smoke shifts from white to thin blue, indicating that moisture and volatile compounds have departed and pyrolysis has become self-sustaining above 300∘C.
What are the temperature ranges and characteristic residence times of slow, fast, and flash pyrolysis?
Slow pyrolysis operates at 300–500∘C (best for charcoal); fast pyrolysis operates at 400–600∘C (short residence time); flash pyrolysis operates at 400–800∘C (shortest residence time of about 2 s or less).
What feedstock preparation and processing steps are required to produce bio-oil via fast or flash pyrolysis?
Feedstock must be dried below 10% moisture content (MC) and ground to approximately 2mm, and vapors must be cooled rapidly after leaving the reactor to avoid cracking into smaller molecules.
What is the typical product distribution yield when dry wood undergoes bio-oil pyrolysis?
Bio-oil yields reach up to 75% of dry wood, while char and non-condensable gases account for approximately 10–15%.
What are the major chemical fractions found in bio-oil?
Water-insoluble pyrolytic lignin (25–30%), water (20–25%), other oxygenated compounds (10–25%), organic acids (5–12%), non-polar hydrocarbons (5–10%), and anhydro-sugars (5–10%).
What is the heating value of bio-oil, and what conventional fuels can it substitute?
It has a heating value of 16–19MJ/kg and can replace fuel oil and natural gas in boilers, gas turbines, and diesel engines.
What is wood gasification and at what operating temperature range does it occur?
Gasification is the heating of wood to 1200–1400∘C with limited oxygen (partial combustion) to generate a combustible gas mixture.
What distinguishes producer gas from syngas in terms of production method and composition?
Producer gas is generated via air-blown gasification and contains nitrogen (resulting in a lower heating value), whereas syngas is primarily H2+CO produced using oxygen-blown or FICFB systems.
What are the four successive phases that occur during biomass gasification?
How do updraft and downdraft gasifier configurations differ in tar output?
Updraft gasifiers are the oldest configuration and yield approximately 10% tar, whereas downdraft gasifiers produce a cleaner output because tars are cracked into combustible gases.
What conditions and chemical reactions govern the synthesis of fuel-grade methanol from syngas?
A syngas gasifier operating at 900∘C and 5MPa drives: CO+2H2→CH3OH and CO2+3H2→CH3OH+H2O.
Which organism ferments syngas into bioethanol, and why is this pathway advantageous over direct sugar fermentation?
Clostridium ljungdahlii converts CO and CO2 into ethanol; this enables total wood utilization, converting rigid lignin and bark that cannot be degraded by enzymes.
What is the general chemical reaction, catalyst type, and required gas ratio for Fischer-Tropsch Liquid (FTL) synthesis?
The reaction is nCO+2nH2→CnH2n+2+nH2O, requiring an iron or cobalt catalyst and an H2:CO ratio of approximately 2:1.
Under what specific conditions can softwood chip digestibility be increased from approximately 5% to over 80%?
By heating the softwood chips at 215∘C for 180 s using 2.5%SO2 as an acid catalyst.
What temperature and pressure regimes characterize the two stages of dilute sulfuric acid hydrolysis?
Stage 1 operates at 130–140∘C for approximately 30 min to extract hemicellulose sugars; Stage 2 operates at 180–190∘C under 1.6MPa to hydrolyze cellulose.
What chemical compound is used to neutralize acid hydrolysate before yeast fermentation?
Slaked lime, Ca(OH)2.
What reaction, organism, and operating conditions are used to ferment hexose sugars to bioethanol?
Yeast (Saccharomyces cerevisiae) ferments hexose sugars at 35∘C within approximately 12 h via the reaction: C6H12O6→2C2H5OH+2CO2.
Why does hemicellulose break down more readily than cellulose under thermal and chemical treatments?
Cellulose is an unbranched, crystalline chain of glucose bonded tightly by hydroxyl (OH) groups, whereas hemicellulose is an irregular, branched polymer with side branches (acetyl, glucuronic acid, galactose, arabinose) that acids and heat easily degrade.
What are the structural features and biochemical limitations of lignin?
Lignin is a rigid, cross-linked 3D web of ring-shaped units that glues wood fibers together; it is not fermentable by enzymes and survives hydrolysis, but it can be utilized in thermochemical gasification.
How do 1st, 2nd, and 3rd generation biofuel feedstocks differ in composition and application?
1st generation utilizes edible food crops (corn, cane, edible oils) raising food vs. fuel issues; 2nd generation uses lignocellulosic residues, wood waste, and non-edible plant oils (e.g., Jatropha); 3rd generation uses micro- and macro-algae or engineered lipids.
How do bioethanol and biodiesel compare regarding oxygen content, lower heating value (LHV), and combustion ratings?
Bioethanol has ∼35% oxygen, an LHV of ∼26.7MJ/kg, and an octane rating of 108–114. Biodiesel has 10–11% oxygen, an LHV of 37–39MJ/kg, and a cetane rating of 45–70.
What is the primary feedstock for Coconut Methyl Ester (CME) in the Philippines, and who is the largest producer?
All 11 listed producers use copra (dried coconut meat); Chemrez Technologies is the largest single producer with a capacity of 90 million L.
Which facilities are the largest bioethanol producers in the Philippines, and what feedstock do they process?
Green Future Innovations (54 million L) and San Carlos Bioenergy (40 million L), both utilizing sugarcane.
Why were the Philippine alcogas and coco-diesel programs discontinued in 1983?
World crude oil prices fell while domestic market prices for coconut and sugar increased.
What biofuel blending targets were established under Republic Act 9367 (Biofuels Act of 2006)?
A mandatory blend of 2% biodiesel (B2) by 2009 and 10% bioethanol (E10) by 2020.
What are the primary functions of RA 9136, RA 9513, and RA 9729 in the Philippine renewable energy sector?
RA 9136 (EPIRA, 2001) promotes renewable energy via private investment; RA 9513 (Renewable Energy Act, 2008) grants incentives for renewable developers; RA 9729 (Climate Change Act, 2009) established the Climate Change Commission.