Chapter 12: Reactor Networks - Reaction Engineering Basics

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/22

flashcard set

Earn XP

Description and Tags

Flashcards covering Chapter 12: Reactor Networks from Reaction Engineering Basics, including series/parallel configurations, CSTR cascades, thermally backmixed PFRs, recycle PFRs, steady-state multiplicity, and optimization examples.

23 Terms

1
New cards

What defines a series network of chemical reactors?

A configuration where the outlet stream from each reactor becomes the feed stream to the next reactor in sequence.

2
New cards

What defines a parallel network of chemical reactors?

A configuration where a single feed stream is split and distributed among multiple reactors, and the outlet streams from all reactors are subsequently mixed into a single product stream.

3
New cards

Under what condition is a series network of adiabatic PFRs equivalent to a single adiabatic PFR?

When there is no heating or cooling of the individual PFRs and no heating or cooling between one PFR outlet and the next PFR inlet, the network behaves identically to a single adiabatic PFR with a volume equal to the sum of the individual reactor volumes.

4
New cards

What single reactor type does a series network (cascade) of isothermal or adiabatic CSTRs approach as the number of reactors approaches infinity?

A single PFR with the same total volume as the sum of the CSTR volumes.

5
New cards

Why does a series cascade of CSTRs fail to approach PFR behavior as the number of reactors approaches infinity if heat exchange occurs with a perfectly mixed fluid?

Because each CSTR exchanges heat with a fluid at uniform temperature, preventing the continuous axial temperature gradient characteristic of a non-adiabatic PFR.

6
New cards

Why should mixing parallel reactor effluent streams of unequal conversion be avoided?

Mixing streams of unequal conversion effectively undoes some of the reaction that has taken place; because reaction rate decreases with conversion for typical kinetics, attaining the resulting intermediate conversion directly would require a smaller total reactor volume.

7
New cards

How do stream temperature and reagent concentration change across an ideal stream splitter?

They do not change. The temperature and concentration (or partial pressure) of every leaving stream are identical to those of the entering stream.

8
New cards

Why is it advantageous to place a small CSTR in series ahead of a PFR for an autocatalytic reaction such as cell growth?

A PFR requires both cells and substrate in its feed to initiate growth, whereas a preceding CSTR allows a pure substrate feed because the backmixing in the CSTR maintains a continuous population of growing cells that inoculates the PFR feed.

9
New cards
<p>What reactor configuration is depicted in this schematic diagram?</p>

What reactor configuration is depicted in this schematic diagram?

A thermally backmixed PFR, in which heat from the reactor product stream (stream 2) is transferred to the cold feed stream (stream 0) across a counter-current heat exchanger before the feed enters the PFR (stream 1).

10
New cards

How does a thermally backmixed PFR combine the best features of both a CSTR and a PFR for an exothermic reaction?

It immediately preheats the feed to elevate the rate constant at the inlet (like a CSTR), while avoiding dilution with product so that the reactant concentration starts high and decreases gradually along the length (like a PFR).

11
New cards

What does it mean for an exothermic reaction in a thermally backmixed PFR to occur 'auto-thermally'?

The reaction achieves and maintains a high steady-state conversion using only the heat generated by the reaction transferred via the heat exchanger, without requiring continuous external heating.

12
New cards

Why can multiple steady states occur in a thermally backmixed PFR?

Because thermal backmixing couples the reactor output to its input: the outlet temperature determines how much heat is transferred to the feed, and the resulting inlet temperature in turn determines the outlet conversion and temperature.

13
New cards

When numerically solving the coupled model equations for a thermally backmixed PFR, why must the reactor inlet temperature (T1T_1) be chosen as an unknown in the algebraic heat exchanger solver?

Because the PFR initial-value ordinary differential equations (IVODEs) require T1T_1 as an initial condition at the inlet, allowing the PFR equations to be integrated within the residual function of the heat exchanger equations.

14
New cards
<p>What reactor configuration is depicted in this schematic diagram?</p>

What reactor configuration is depicted in this schematic diagram?

A recycle PFR consisting of a stream mixer (MM), a plug flow reactor, and a stream splitter (SS) where recycle stream 4 is returned to mix with fresh feed stream 0.

15
New cards

How is the recycle ratio (RR) defined for a recycle PFR?

The ratio of the flow rate of the recycle stream (stream 4) to the flow rate of the final product stream (stream 3): R=V˙4V˙3=n˙4n˙3R = \frac{\dot{V}_4}{\dot{V}_3} = \frac{\dot{n}_4}{\dot{n}_3}.

16
New cards

What reactor behavior does a recycle PFR approach as the recycle ratio approaches infinity (R→∞R \rightarrow \infty)?

It approaches the behavior of an ideal continuous stirred-tank reactor (CSTR) in both temperature and composition.

17
New cards

Why would a recycle PFR be preferred over a CSTR when CSTR-like behavior is desired for a heterogeneous catalytic reaction?

The catalyst can be packed into a fixed bed in the PFR through which fluid flows, avoiding the mechanical difficulties of suspending and perfectly mixing solid catalyst particles in a CSTR.

18
New cards

Why can an exothermic autocatalytic reaction operating at high conversion require a smaller volume in a recycle PFR than in a CSTR?

In a CSTR, high conversion forces the reactant concentration to be near zero everywhere, causing a very low reaction rate throughout. In a recycle PFR, the inlet rate is enhanced by returned product and elevated temperature, and then drops along the length to the CSTR value, producing a higher average rate and thus smaller volume.

19
New cards
<p>What configuration is shown in this schematic diagram for the water-gas shift reaction network?</p>

What configuration is shown in this schematic diagram for the water-gas shift reaction network?

Two steady-state adiabatic packed bed reactors (R1R1 and R2R2) connected in series with an interstage heat exchanger (HEHE) providing cooling between them.

20
New cards

In the two-stage series water-gas shift process (Example 12.4.2), what are the distinct roles of the high-temperature and low-temperature reactors?

The first reactor uses a high-temperature catalyst to rapidly achieve the majority of conversion at high rates; the second reactor uses a low-temperature catalyst after interstage cooling because lower temperatures shift the thermodynamic equilibrium toward higher CO conversion without exceeding catalyst thermal limits.

21
New cards

Why is there a minimum total volume when sizing two adiabatic CSTRs in series for an exothermic reaction to reach a specified high conversion?

Because the reaction rate passes through a maximum at an intermediate conversion due to competing effects of rising temperature and falling reactant concentration; sizing the first CSTR near this peak rate maximizes its rate and minimizes the total volume required relative to a single CSTR.

22
New cards

For two unequally sized PFRs arranged in parallel, which feed splitting strategy yields higher overall conversion: equal flow rates or equal space times?

Equal space times, because splitting feed proportionally to reactor volume produces identical conversion in both effluent streams, avoiding the conversion loss that occurs when mixing streams of unequal conversion.

23
New cards

In a thermally backmixed PFR with three steady states (Example 12.4.6), which states are stable and which is unstable?

The upper and lower steady states are stable, while the middle steady state is unstable.