1/32
Vocabulary practice flashcards covering fundamental terms, physical principles, and mathematical definitions from Units I, II, and III of Engineering Physics (Measurements & Semiconductors, Magnetic Materials & Motors, and Lasers & Optical Fibres).
Measurement
The process of comparing an unknown physical quantity with an accepted standard quantity of the same kind, where the result is expressed as a numerical value and a unit.
Fundamental units
Independent units that are not defined using other units and form the base of the SI system, such as the metre (m), kilogram (kg), second (s), and ampere (A).
Derived units
Units obtained by combining fundamental units mathematically and depending upon them, such as velocity (ms−1), force (kgms−2 or newton), and energy (kgm2s−2 or joule).
Valence band
The highest energy band normally occupied by valence electrons at 0K.
Conduction band
The energy band above the valence band in which electrons are free to move and conduct electricity.
Forbidden energy gap
The energy gap (Eg) between the valence band and conduction band in which no allowed electron energy states exist.
Electrical conductivity of a semiconductor (σ)
The measure of conductivity given by σ=e(neμe+nhμh), where e is the electronic charge, ne and nh are electron and hole concentrations, and μe and μh are electron and hole mobilities.
Fermi-Dirac distribution function
A mathematical function giving the probability f(E) that an available energy state of energy E is occupied by an electron at absolute temperature T: f(E)=1+exp(kTE−EF)1, where EF is Fermi energy and k is the Boltzmann constant.
Forward bias (P-N diode)
The biasing arrangement where the P-side is connected to the positive terminal and the N-side to the negative terminal, causing the depletion layer and barrier potential to decrease and allowing a large majority-carrier current to flow after the cut-in voltage.
Reverse bias (P-N diode)
The biasing arrangement where the P-side is connected to the negative terminal and the N-side to the positive terminal, causing the depletion layer and barrier potential to increase, blocking majority carriers, and allowing only a small reverse saturation current due to minority carriers until breakdown.
Magnetic field strength (H)
The magnetising force that produces a magnetic field in a material, measured in the SI unit of Am−1.
Magnetic flux (ϕ or B)
The total magnetic field passing through a given surface, given by ϕ=BAcos(θ) for a uniform field, with the SI unit of weber (Wb).
Magnetization (M)
The magnetic dipole moment per unit volume of a material, expressed in the SI unit of Am−1.
Magnetic permeability (μ)
The ability of a material to support the formation of a magnetic field within it, given by μ=HB for a linear medium, with the SI unit of Hm−1.
Magnetic susceptibility (χm)
The dimensionless ratio of magnetization to applied magnetic field strength, defined by χm=HM.
Diamagnetic materials
Materials that are weakly repelled by a magnetic field, have small and negative susceptibility (χm), relative permeability slightly less than 1, and an induced magnetic moment that opposes the field (e.g., bismuth, copper).
Paramagnetic materials
Materials that are weakly attracted to a magnetic field, have small and positive susceptibility (χm), relative permeability slightly greater than 1, and some magnetic moments that align with the field (e.g., aluminium, platinum).
Ferromagnetic materials
Materials that are strongly attracted to a magnetic field, have large and positive susceptibility (χm), relative permeability much greater than 1, and domains that align strongly with the field (e.g., iron, cobalt, nickel).
Soft magnetic materials
Magnetic materials that are easily magnetized and demagnetized, having low coercivity, low retentivity, and a narrow hysteresis loop with low hysteresis loss; commonly used in transformer cores and electromagnets.
Hard magnetic materials
Magnetic materials that are difficult to magnetize and demagnetize, having high coercivity, high retentivity, and a wide hysteresis loop with high hysteresis loss; used for permanent magnets.
Resonant cavity
An optical arrangement consisting of two mirrors placed at the ends of an active medium—one fully reflecting and one partially reflecting—allowing light to travel repeatedly through the active medium for amplification before emerging as a laser beam.
Pumping
The process of supplying external energy to the active medium to raise atoms or molecules from lower energy levels to higher energy levels, helping to achieve population inversion.
Stimulated emission
The process where an incident photon of energy hν=E2−E1 interacts with an atom in the excited state, stimulating it to drop to a lower energy state and emit a second photon with the identical frequency, phase, direction, and polarization.
Population inversion
The non-equilibrium condition necessary for laser action in which the number of atoms in the higher energy state exceeds the number in the lower energy state (N2>N1).
Metastable state
An excited energy state in which atoms remain for a comparatively longer lifetime than in ordinary excited states, allowing atoms to accumulate to achieve population inversion.
Spontaneous emission
A process in which an excited atom drops to a lower state and emits a photon on its own, producing incoherent light that is random in direction and phase.
He-Ne gas laser
A gas laser using a mixture of helium and neon at low pressure (typical ratio about 10:1) excited by an electrical discharge, producing a coherent red laser output at a wavelength of 632.8nm.
CO2 gas laser
A molecular gas laser containing carbon dioxide, nitrogen, and helium in which collision-induced energy transfer from excited N2 creates population inversion in CO2, yielding infrared radiation primarily at 10.6μm.
Optical fibre
A thin, flexible, transparent dielectric waveguide consisting of a central core (n1), cladding (n2 with n1>n2), and a protective jacket that transmits light from one end to another via total internal reflection.
Total internal reflection (TIR)
The phenomenon in which a light ray traveling from an optically denser medium to a rarer medium is completely reflected back into the denser medium when the angle of incidence exceeds the critical angle.
Acceptance angle (θa)
The maximum angle measured with the fibre axis at which light can enter the fibre from an outside medium of refractive index n0 and propagate by total internal reflection, defined by n0sin(θa)=n12−n22.
Numerical aperture (NA)
A measure of the light-gathering ability of an optical fibre, defined mathematically as NA=n0sin(θa)=n12−n22, which simplifies to sin(θa) for air (n0≈1).
Acceptance cone
The solid cone formed by all incident light rays capable of entering an optical fibre and propagating through total internal reflection, characterized by a semi-vertical angle of θa and a full cone angle of 2θa.