1/79
Looks like no tags are added yet.
A project requires an initial investment of P4,000,000 and generates annual savings of P900,000 for 8 years. Determine the simple payback period.
4.44 years
A synchronous motor operates at 1200 rpm on a 60 Hz supply. Determine the number of poles.
6
A DC shunt motor draws 22 A from a 220 V supply. If armature resistance is 0.4 ohms and field current is 2 A, determine the back emf.
212.0 V
In a Pelton wheel, the bucket peripheral speed is 10 m/s and the water jet velocity is 25 m/s. The volumetric flow rate of the jet is 0.10 m³/s. If the jet is deflected by 120° and the flow is ideal, what is the power developed?
22.5 kW
In a simple impulse turbine, the nozzle angle at the entrance is 30°. What is the blade-speed ratio for maximum diagram efficiency?
0.433
An impulse turbine operating with a single nozzle has a specific speed of 5. Determine the approximate specific speed if the turbine is modified to operate with two nozzles of identical size.
7
At the eye tip of a centrifugal impeller, the blade velocity is 200 m/s while the uniform axial velocity at the inlet is 150 m/s. If the sonic velocity is 300 m/s, determine the inlet Mach number of the flow.
0.83
In a radial blade centrifugal compressor, the blade tip velocity is 400 m/s and the slip factor is 0.9. Assuming the absolute velocity of flow at inlet is axial, determine the work done per kg of flow.
144 KJ/kg
A Pelton turbine has an overall efficiency of 70%. If the mechanical efficiency is 85%, determine the hydraulic efficiency of the turbine.
82.4%
A large hydraulic turbine develops 400 kW at 900 rpm under a head of 36 m. During testing, a 1:5 scale model operates under a head of 9 m. Calculate the power generated by the model turbine.
2.0 kW
An engine with a foundation area of 145 ft² supports a machine weighing 24,500 lbs. If soil bearing capacity is 0.48 kg/cm², determine the engine speed. Use e = 0.11.
1918 rpm
12. A water jet of diameter 80 mm issues at 16 m/s. Find the horsepower exerted.
A) 12.8 hp
B) 8 hp
C) 10.3 hp
D) 9 hp
Calculated result: approximately 13.8 hp; no option matches.
A pump develops 28 kW. If speed decreases by 40%, find percent decrease in power.
78.4%
A pump develops 52 kW at 320 rpm with fluid specific gravity 1.03, impeller diameter 160 mm. If speed is raised to 640 rpm, diameter = 125 mm, and SG = 0.82, find new power.
96 kW
A feedwater pump raises enthalpy from 2800 kJ/kg at inlet to 2805 kJ/kg at outlet. What is the water velocity?
100 m/s
A submersible pump delivers 360 gpm of water to a height of 8 ft above the ground. The pump is installed 140 ft below ground level, and drawdown during pumping is 10 ft. The static water level is 20 ft above the pump. Determine the pump power.
9.4 kW
A radial-flow pump with specific speed 2400 is required to deliver 270 gpm against a head of 132 ft at a speed of 2200 rpm. Find the number of stages (impellers).
4 stages
A piston-type positive displacement pump has a piston diameter of 10 in and a stroke length of 3.0 in. The crankshaft runs at 250 rpm. Calculate the output in cfm if the volumetric efficiency is 92%.
31.3 cfm
A three-phase wye-connected alternator is rated at 1200 kVA and 6600 volts. The resistance per phase is 0.5 ohm while the field circuit resistance is 0.90 ohm. The friction and windage losses are 8 kW and the core losses are 28 kW. Determine the rated phase voltage in kV.
3.81
If the rotational speed of a centrifugal pump is increased four times, by what factor does the developed head change?
16
An industrial fan delivers 32 m³/s through a 0.75 x 1.0 m duct. Static pressure = 160 mm water gage, air density = 1.2 kg/m³. Find air horsepower.
114.2 hp
A machine foundation and machine system has a total mass of 2500 kg and spring stiffness of 1.8×10⁶ N/m. Determine the natural frequency of vibration.
4.27 Hz
A 12 MVA, 2400 V alternator is directly connected to a bus through a 4% reactor and OCB. The breaker relays are adjusted to open 0.3 second after a short circuit occurs. Determine the normal current capacity of the breaker.
2887 A
A 100 MVA turbo-alternator operating at full load at 60 Hz suddenly experiences a reduction of 50 MW load. Due to the delay in the governor system, the steam valves begin to close after 0.6 second. Determine the excess energy supplied to the rotating parts.
30 MJ
In a soil investigation for a machine foundation, the spread footing is designed with a factor of safety of 3. If the allowable bearing pressure of the soil is 24 kPa, determine the minimum net bearing capacity required for the footing.
72 kPa
A machine foundation is designed with a trapezoidal cross-section having bases of 1.5 m and 2.5 m. The height is 2 m and the foundation length is 3.5 m. Determine the cubic yard of sand required for a 1:2:4 concrete mixture.
8.05 yd³
A machine foundation block has dimensions of 2 m x 1.5 m x 1 m. If the density of concrete is 2400 kg/m³, determine the mass of the foundation.
7200 kg
The outlet of a turbine runner is located 5 m above the tail race level. If the atmospheric pressure head is 10.3 m of water, what is the maximum pressure head possible at the runner exit inside the divergent draft tube?
5.3 m
A double acting reciprocating pump with bore of 30 cm running at 300 rpm has 7% slip. If discharge volume is 4168.31 GPM. Find the length of stroke of the piston.
400 mm
A pump has a suction pressure of 20 kPa vacuum and discharge pressure is 250 kPa. The pump is used to deliver 100 lit/s of water. If heat loss from the pump is 5 kW, find the brake power of motor needed.
32 kW
What type of feasibility report is prepared when site layout and process are already defined?
Detailed feasibility
Which element of feasibility study considers laws, zoning, and permits?
Legal feasibility
What phase includes preparation of a feasibility report?
Planning phase
Which project dimension studies the demand-supply gap?
Market feasibility
Which tool is used to forecast future demand in project studies?
Trend analysis
Which plant engineering document shows equipment arrangement?
Plant layout drawing
Which analysis estimates time-phased project activities?
PERT/CPM
Which factor is NOT usually considered in technical feasibility?
Market size
Which tool is commonly used to monitor project schedule?
Gantt chart
Which tool is best for project scheduling under uncertainty?
PERT
What safety program ensures machines are de-energized before maintenance?
Lockout/Tagout
What safety device prevents machinery from operating without guards?
Interlock system
Which gas is commonly linked with confined space accidents?
Carbon Monoxide
Which fire extinguisher type is suitable for electrical fires?
CO2 extinguisher
Which standard provides guidelines for occupational health and safety management systems?
ISO 45001
Which fire class involves flammable liquids?
Class B
Which fire class involves metals like magnesium and sodium?
Class D
Which standard addresses process safety management of highly hazardous chemicals?
OSHA 29 CFR 1910.119
Which color coding is used for portable water pipes in plants?
Green
Which document outlines safe handling of chemicals?
Safety Data Sheet
What does Per Million Man-Hours measure?
Safety performance
Which factor is prevented by maintaining Net Positive Suction Head?
Cavitation
Which turbine is suitable for high heads and low discharge?
Pelton wheel
What type of turbine converts pressure head into kinetic energy before striking the runner?
Impulse turbine
Which fan is widely used in power plant induced draft?
Axial fan
Which pump delivers fluid using a rotating screw?
Screw pump
Which turbine is most efficient for medium head?
Francis turbine
Which law defines relation between pump power and speed?
P ∝ N³
Which pump has self-priming capability?
Positive displacement pump
Choking in compressors occurs when:
Mach number at throat = 1
What is the preferred frequency of a machine foundation relative to the machine?
Far from the machine's frequency
What property of soil determines its ability to resist loads from machinery foundations?
Bearing capacity
Which type of vibration must be avoided in foundation design?
Resonance
Which type of foundation is commonly used for large reciprocating machines?
Block foundation
What type of foundation is used when soil has low bearing capacity?
Pile foundation
What is the recommended factor of safety for foundation bearing capacity?
5
Which type of foundation is suitable for turbo-machinery?
Raft foundation
A machine foundation supporting a high-speed turbine has insufficient damping. Which of the following effects is most likely during operation near critical speed?
Excessive vibration amplitude
What factor increases foundation settlement?
Weak soil compressibility
Which machine foundation requires special analysis for horizontal forces?
Centrifugal machines
Which type of DC motor has high starting torque?
Series motor
What machine can operate as both motor and generator?
DC machine
What is the formula for synchronous speed of AC machines?
Ns = 120f / P
Which type of induction motor is widely used in industry?
Squirrel cage induction motor
Which factor improves power factor of induction motors?
Capacitor banks
Which test determines voltage regulation of alternators?
Open circuit and short circuit test
What is the starting problem of synchronous motors?
they are not self-starting
which test is used to determine the efficiency of large dc machines?
Hopkinson's test
What is the application of capacitor-start single-phase motors?
Refrigerators and compressors
Which industrial safety device automatically disconnects electrical power during leakage current conditions?
Ground fault interrupter