Nav Eng. I Test 2

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/87

encourage image

There's no tags or description

Looks like no tags are added yet.

88 Terms

1
New cards

Keel

Centerline bottom structure; the hull's backbone.

2
New cards

Shell plating

Outer skin that gives strength and watertightness.

3
New cards

Stiffeners (frames and longitudinals)

Support the plating and carry loads into the hull.

4
New cards

In compartment 3-75-4-M, what does the 3 tell you?

Vertical location (deck level).

5
New cards

In compartment 3-75-4-M, what does the 75 tell you?

Forward boundary frame number.

6
New cards

In compartment 3-75-4-M, what does the 4 tell you?

Side of ship: even = port, odd = starboard.

7
New cards

In compartment 3-75-4-M, what does the M tell you?

Primary use of the space (magazine).

8
New cards

Why do coatings protect structure?

They separate metal from the environment; damage needs repair.

9
New cards

Two forms of cathodic protection

Sacrificial anodes and impressed current.

10
New cards

Redundancy

An alternate component or path that can preserve a required function.

11
New cards

Common cause failure

One event (power loss, flooding, pipe damage) that defeats multiple redundant units.

12
New cards

Separation

Independent supplies and separated routes, so redundancy is not defeated at once.

13
New cards

Two cooling pumps share one power supply. What is the flaw?

Not separated: one common cause disables both.

14
New cards

Growth margin: weight and stability

New equipment uses weight allowance; vertical location matters as much as mass.

15
New cards

Growth margin: space and structure

Foundations, cable routes, access, and maintenance clearances must still fit.

16
New cards

Growth margin: power and cooling

Electrical demand and rejected heat draw on the service margins.

17
New cards

Growth margin: endurance and cost

Added demand changes fuel use, stores, maintenance, and availability.

18
New cards

Hydraulic force equation

F = ΔP × A (pressure difference times effective piston area).

19
New cards

What sets hydraulic actuator speed?

Flow rate divided by effective piston area (v = Q/A).

20
New cards

Hydraulic power (approximate)

P ≈ ΔP × Q. Losses become heat.

21
New cards

Where does hydraulic energy stay stored?

Accumulators, trapped pressure, and suspended loads.

22
New cards

First step before hydraulic work

Approved isolation and energy control; verify the safe condition.

23
New cards

Hydraulic leak safety rule

Keep hands away from leaks; stay clear of rams, linkages, and moving loads.

24
New cards

Fluid condition requirements

Use the specified fluid and keep it clean; control leakage and ignition hazards.

25
New cards

Why compress in stages?

Each stage feeds the next at a higher inlet pressure.

26
New cards

Intercooler

Cools air between stages, cutting the next stage's compression work.

27
New cards

Aftercooler

Cools air after the final stage, before drying and storage.

28
New cards

How is water removed from compressed air?

Cooling condenses it; separators and drains remove liquid; dryers remove vapor.

29
New cards

What does moisture do downstream?

Corrosion, impaired controls, and icing during expansion.

30
New cards

Two heat exchangers on a two-stage compressor

Intercooler between stages; aftercooler after the last stage.

31
New cards

Flash distillation

Heated feed partly vaporizes after a pressure reduction.

32
New cards

Vertical basket distiller

Heating steam boils feed through a heat-transfer surface.

33
New cards

Vapor compression distilling

A compressor lets the vapor's condensation heat be reused.

34
New cards

Reverse osmosis

Pressure drives water through a membrane that rejects salt.

35
New cards

RO product and reject streams

Product is permeate; most salt leaves in the reject (brine).

36
New cards

Why does feed flash?

Pressure drops, so saturation temperature drops below the feed's temperature.

37
New cards

Flash plant: what happens to the brine?

Liquid that did not flash continues to later, lower-pressure stages.

38
New cards

Flash plant: vapor path

Vapor passes a separator, then condenses and is collected as distillate.

39
New cards

Flash plant: heat recovery

Condensing vapor heats incoming feed, cutting external heating demand.

40
New cards

Evaporator

Absorbs heat as refrigerant evaporates.

41
New cards

Compressor (refrigeration)

Raises refrigerant vapor pressure and temperature.

42
New cards

Condenser

Rejects heat and condenses the refrigerant.

43
New cards

Expansion valve

Reduces refrigerant pressure (throttling).

44
New cards

Heat rejected by a refrigeration plant

Heat rejected = heat removed + compressor work.

45
New cards

Cycle step 1→2 on a T–s diagram

Isentropic compression: work in, pressure, temperature, enthalpy rise.

46
New cards

Cycle step 2→3

Condensation at high pressure; rejects heat, leaves as liquid.

47
New cards

Cycle step 3→4

Throttling: pressure drops, some liquid flashes, enthalpy about constant.

48
New cards

Cycle step 4→1

Evaporation: absorbs heat, then slightly superheats before the compressor.

49
New cards

Three loops in chilled-water cooling

Refrigerant loop, chilled-water loop, seawater loop.

50
New cards

Chilled-water loop job

Carries heat from the cooling coils in the spaces to the chiller.

51
New cards

Seawater loop job

Takes condenser heat and rejects it overboard.

52
New cards

Resistors in parallel: voltage and current

Same voltage across each branch; current divides between them.

53
New cards

Parallel resistance formula

1/Req = 1/R1 + 1/R2 + 1/R3.

54
New cards

Three 6 Ω branches across 12 V

2 A each, 6 A total, Req = 2 Ω.

55
New cards

Kirchhoff's voltage law

Around a closed loop, voltage rises equal voltage drops.

56
New cards

KVL check: 12 V across 4 V and 8 V drops

+12 − 4 − 8 = 0.

57
New cards

DC vs AC

DC flows one way (batteries). AC reverses periodically; frequency in hertz.

58
New cards

Open circuit vs short circuit

Open stops current; a short provides an unintended low-resistance path.

59
New cards

Safety point about stopped equipment

It may still have voltage present.

60
New cards

Prime mover

Steam turbine, gas turbine, or diesel that turns the generator.

61
New cards

Governor's job on an isolated generator

Adjusts input to hold speed, which holds frequency.

62
New cards

Excitation

Field current, used to regulate generator terminal voltage.

63
New cards

Generator action

Mechanical in, electrical out: conductor + magnetic field + relative motion.

64
New cards

Motor action

Electrical in, mechanical out: current-carrying conductor + magnetic field.

65
New cards

Transformer: primary and secondary

Primary AC makes changing core flux; flux induces secondary voltage.

66
New cards

What stays the same through a transformer?

Frequency.

67
New cards

Rectifier

AC in, DC out; diodes conduct mainly one way.

68
New cards

Inverter

DC in, AC out.

69
New cards

Variable-frequency drive

Controls AC frequency and voltage to adjust motor operation.

70
New cards

Selective tripping

The nearest protective device isolates the fault; healthy circuits stay energized.

71
New cards

Fuse vs breaker

A fuse melts to interrupt current; a breaker trips open and can be reset.

72
New cards

How does subdivision limit damage?

Watertight bulkheads and decks confine flooding to one space.

73
New cards

What keeps a watertight boundary intact?

Closed fittings and sealed penetrations.

74
New cards

When do you classify a fire by material?

After de-energization; the burning material sets the class and agent.

75
New cards

Typical fire agents

Water, suitable foam, dry chemical, CO₂.

76
New cards

Two questions before isolating a system

What does it provide, and who loses support when it goes?

77
New cards

Heel

Side-to-side inclination, e.g. from wind or turning.

78
New cards

List

A sustained transverse inclination, usually from off-center weight.

79
New cards

Trim

Fore-and-aft attitude; difference between aft and forward draft.

80
New cards

GZ (righting arm)

Perpendicular distance between the lines of action of weight and buoyancy.

81
New cards

Righting moment formula

RM = displacement × GZ.

82
New cards

Free-surface effect

Liquid shifts to the low side and reduces the righting moment.

83
New cards

First check on any technical reference

That it matches the ship, equipment, and configuration.

84
New cards

3M schedule

Shows maintenance due and who is assigned.

85
New cards

MIP

Maintenance Index Page: requirements for an equipment group.

86
New cards

MRC

Maintenance Requirement Card: instructions for the specific check.

87
New cards

Caution tag vs danger tag

A caution tag never substitutes for a required danger tag.

88
New cards

Short-answer structure

State what changes, then explain why.