Woodworking Machinery Safety, Operations, and Board Foot Calculations

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/27

flashcard set

Earn XP

Description and Tags

Vocabulary flashcards covering tool safety, operational procedures, and board foot formulas for radial arm saws, band saws, table saws, and drill presses.

28 Terms

1
New cards

Radial Arm Saw Size

Determined by the largest size blade that can be mounted on the saw.

2
New cards

Radial Arm Saw Cutting Motion

An operation where the operator pulls the blade toward themselves and through the wood, unlike a table saw.

3
New cards

Radial Arm Saw Advantage

The ability to cut longer boards compared to what can be managed on a table saw.

4
New cards

Radial Arm Saw Crosscutting Operations

Specific crosscutting cuts that can be performed on the machine, including mitter cuts and rebbet cuts.

5
New cards

Radial Arm Saw Departure Procedure

The required safety routine before leaving the tool: shut off the motor and wait for the blade to come to a complete stop.

6
New cards

Band Saw Cut Types

The two primary categories of cuts performed on the band saw: straight cuts and irregular cuts.

7
New cards

Relief Cuts

Cuts made on a band saw prior to executing long curved cuts to relieve blade tension and prevent binding.

8
New cards

Upper Blade Guides

Band saw components that must be positioned as close to the board as possible during operation.

9
New cards

Band Saw Right Hand Placement

Positioned at the back of the board pushing the stock forward, rather than in front guiding it.

10
New cards

Band Saw Operator Stance

The proper standing position for the operator, located on the left side of the blade.

11
New cards

Band Saw Cutting Order

The procedural rule stating that short cuts must always be completed before making long cuts.

12
New cards

Table Saw Blade Height

The required clearance height of the saw blade above the wood stock, set to exactly 18′′\frac{1}{8}''.

13
New cards

Table Saw Operator Stance

The operator standing location, positioned slightly to the left side of the blade.

14
New cards

Miter Gauge (Miter Guage)

The guiding accessory that must always be used when performing a crosscut on a board using the table saw.

15
New cards

Pushing Stick

The safety device that must always be used to feed stock when ripping a board on the table saw.

16
New cards

Table Saw Blade Orientation

The directional setup where the teeth of the rotating blade point towards the operator.

17
New cards

Pre-Table Saw Board Preparation

The milling procedures required prior to running stock through the table saw: joint the edge and the surface, and plane the board.

18
New cards

Dado Blades

A series of specialized blades stacked and used together on the table saw to cut wide grooves.

19
New cards

Table Saw Arbor Nut Loosening

The direction required to loosen the arbor nut by pulling it toward you.

20
New cards

Kickback (Kicking Back)

The primary safety danger to guard against when ripping a board on the table saw.

21
New cards

Chuck Key Safety Rule

The safety mandate requiring the chuck key to be removed from the chuck before turning on the drill press.

22
New cards

Drill Press Speed Adjustment Rule

The operational restriction stating that it is not permissible to change the drill press speed at any arbitrary time.

23
New cards

Drill Press Braking Rule

The safety regulation prohibiting operators from grabbing the rotating chuck with their hands to bring the machine to a halt.

24
New cards

Drill Press Clamping Rule

The safety guideline requiring small workpieces to always be clamped down securely before drilling.

25
New cards

Board Feet Formula

The mathematical equation used to calculate lumber volume: No. Pcs.×Thickness×Width×Length144=BD’\frac{\text{No. Pcs.} \times \text{Thickness} \times \text{Width} \times \text{Length}}{144} = \text{BD'}.

26
New cards

Board Feet Thickness Rounding Rule

The lumber rule confirming that when figuring board feet, any thickness less than 1′′1'' (such as 34′′\frac{3}{4}'') is rounded up to 1′′1''.

27
New cards

Board Feet Dimension Rounding

The convention of rounding fractional measurements up to the next full whole inch (e.g., 612′′6\frac{1}{2}'' rounds to 77, and 7212′′72\frac{1}{2}'' rounds to 7373).

28
New cards

Unit Cost per Board Foot

The current annual rate for shop lumber, priced at $2.50\$2.50 per board foot.