1/24
Vocabulary flashcards covering stress, strain, deformation mechanisms, slope stability factors, and classification systems of mass wasting based on Geomorphology Lecture 16.
Stress
An internal force in opposition to an external force, defined as force per unit area. It is measured in newtons per square metre (Nm−2 or Pa), with rock stresses typically on the order of MPa (106Pa) or MN (106Nm−2).
Normal Stress (σ)
The stress component acting perpendicular to a surface or shear plane, which functions on flat surfaces to hold objects in place through gravity.
Shear Stress (τ)
The stress component acting parallel to a shear plane, acting as the downslope component of total stress and representing the most common erosional stress.
Strain
The physical deformation or change in dimension of a natural material resulting from an applied stress over time.
Elastic Deformation
A mechanical deformation behavior described by Hooke's Law where strain is directly proportional to applied stress and is fully recoverable upon stress removal, though failure may occur beyond the elastic limit.
Plastic Deformation
A deformation behavior where a material shows no strain until reaching a critical stress threshold (the yield point), after which irreversible deformation or failure occurs abruptly.
Viscous Deformation
A deformation process dependent on molecular cohesion and consistency where any non-zero applied stress causes strain, and the rate of strain is proportional to the applied stress.
Newtonian Viscous Fluid
A viscous fluid that exhibits a direct, linear relationship between applied stress and strain rate.

Anatomy of a Fold
The structural components of folded strata, consisting of an anticline, a syncline, fold limbs, an axial plane, and a hinge line.
Mass Wasting
The downslope movement of rock, soil, or surface material under the direct influence of gravity.
Slope Failure
The collapse of a rock or sediment mass occurring when shear stress exceeds the collective shear strength and forces holding the material on the slope.
Slides (Mass Wasting Mode)
A rapid, accelerating mass wasting mode involving dry material that moves as a cohesive unit along a well-defined failure plane with a constant velocity profile.
Translational Slide
A fundamental slide-based mass wasting feature in which a cohesive block of soil or rock slides along a planar inclined surface, such as bedding or joint planes.

Slump (Rotational Slide)
A slide-based mass wasting event involving a cohesive mass of soil or rock displacing downslope along a concave-upward, curved failure plane.

Expandable Clays
Clay minerals that absorb polar water molecules between their sheets, leading to volumetric expansion that exerts lateral pressure and reduces slope shear strength.

Liquefaction
A process in water-saturated sediment where pore water completely surrounds grains and eliminates grain-to-grain contact friction, transforming the mass into a fluid-like state.
Falls and Topples
A mass wasting mechanism where a detached block of rock or soil initiates movement along a failure plane before falling freely through the air.

Talus
An accumulation of rock debris and fallen fragments that settles at the base of a cliff or steep slope at the angle of repose.
Flows (Mass Wasting Mode)
A rapid and accelerating mass wasting movement of wet or dry material characterized by internal inter-particle shearing, where velocity decreases downward through the deforming mass.

Heaves and Creep
A slow, imperceptible mass wasting process where individual particles displace cyclically: expanding normal to the slope and contracting vertically under gravity, with velocity decreasing with depth.
Creep
The gradual, slow plastic deformation of soil and rock materials downslope under the persistent influence of gravity.
Solifluction
A specialized mass wasting process involving flow, creep, and sliding driven by the seasonal surficial thawing of water-saturated soil atop impermeable frozen ground.
Varnes (1958) Classification
An early mass wasting classification system structured around specific landform types, distinguishing movements by failure mode (slide and flow), material type (bedrock, soil), and movement rate.

Carson and Kirkby (1972) Classification
A process-based classification model that organizes mass wasting phenomena according to three fundamental parameters: mode of movement (slide, flow, heave), velocity (fast to slow), and moisture content (wet to dry).

Lemieux Landslide
A notable historical landslide occurring on June 20, 1993, near Ottawa, where sensitive soils collapsed into the Nation River and disrupted a roadway.