Switchboards, Switchgear, and Electrical Protection Systems

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/77

flashcard set

Earn XP

Description and Tags

Comprehensive practice flashcards covering vocabulary terms, operational principles, and standards in switchgear, switchboards, busbars, transformers, and electrical protection systems.

78 Terms

1
New cards

Switch-Fuse

An isolating switch connected in series with stationary fuses, mechanically isolating the fuse carriers when opened.

2
New cards

Fuse-Switch

A switching device where the fuse carrier or fuse-link physically forms the moving contact blade that engages the main contacts.

3
New cards

Arc Splitter Plates

A series of V-shaped metal plates in an arc chute that divide, lengthen, cool, and de-ionise an electric arc to extinguish it rapidly.

4
New cards

Fireman's Switch

A red emergency isolating switch featuring an accidental-close lock, clear ON/OFF indications, and an installer label.

5
New cards

Impedance Protection (Distance Protection)

A line protection scheme calculating impedance from the ratio of voltage to current (Z=VIZ = \frac{V}{I}), tripping when Z≤ZsetZ \le Z_{\text{set}}.

6
New cards

Biased Current Differential Relay

A relay comparing operating current (∣Is1−Is2∣|I_{s1} - I_{s2}|) against restraint current (k[Is1+Is2]k[I_{s1} + I_{s2}]) to prevent false tripping during through faults.

7
New cards

Main Overcurrent Device (MOD)

An MCB located between the network supply and consumer unit, rated for at least 6 kA6\text{ kA} (or 9 kA9\text{ kA} if <50 kVA< 50\text{ kVA}) inside an IP-rated enclosure.

8
New cards

Maximum Permissible Touch Voltage

The upper safe contact voltage limit (50 V AC50\text{ V AC} or 120 V DC120\text{ V DC} per IS 10101) between simultaneously accessible conductive parts under normal conditions.

9
New cards

Disconnector (Isolator)

A mechanical switch that opens to provide a visible, safe isolating distance under no-load conditions.

10
New cards

Vacuum Circuit Breaker (VCB)

A circuit breaker operating in an evacuated chamber (≈0.0023 in. Hg\approx 0.0023\text{ in. Hg}) that extinguishes arcs instantly due to the lack of ionizable gas.

11
New cards

Diversity Factor

The ratio of maximum electrical power demand to total connected load (Diversity=Maximum DemandConnected Load\text{Diversity} = \frac{\text{Maximum Demand}}{\text{Connected Load}}), used to prevent equipment oversizing.

12
New cards

Cubicle-Type Switchboard

A floor-standing, factory-built switchgear assembly consisting of modular, segregated sheet-steel cubicles rated up to 6000 A6000\text{ A}.

13
New cards

High Breaking Capacity (HBC) Fuse

A ceramic cartridge fuse filled with silica sand and silver elements capable of clearing short circuits up to 80 kA80\text{ kA} in 0.01 s0.01\text{ s}.

14
New cards

Fusing Factor

The ratio of minimum fusing current to continuous rated carrying current (Fusing Factor=Fusing CurrentRated Current\text{Fusing Factor} = \frac{\text{Fusing Current}}{\text{Rated Current}}), normally between 1.41.4 and 2.02.0.

15
New cards

Gauge Ring

A colour-coded sizing ring in a fuse base that physically blocks the insertion of an inappropriately higher-rated fuse cartridge.

16
New cards

Arc Fault Detection Device (AFDD)

A microprocessor-based protective device that analyses circuit waveforms to detect the high-frequency signatures of series or parallel arcing.

17
New cards

Residual Current Device (RCD)

A core-balance device that monitors current balance between supply and neutral, disconnecting power when leakage exceeds its rated sensitivity (IΔnI_{\Delta n}).

18
New cards

Pre-Arcing Time

The time elapsed between the start of an overcurrent fault and the instant the fuse element melts to initiate an arc.

19
New cards

Cut-Off Current

The maximum instantaneous peak current let through by a protective device before the fault arc is completely suppressed.

20
New cards

Under-Voltage Release

An electromagnetic tripping mechanism that disconnects the breaker if voltage drops below a threshold and prevents reclosing until voltage normalises.

21
New cards

All-Insulated Switchgear

Switchgear housed in non-metallic polymer or GRP enclosures providing total shock protection, corrosion resistance, and eliminating earth bonding between units.

22
New cards

Gas-Insulated Switchgear (GIS)

A compact switchgear assembly where busbars and breakers are sealed in metal tanks filled with pressurised sulfur hexafluoride (SF6\text{SF}_6) gas.

23
New cards

Medium Voltage (MV) Switchgear

Electrical protection and switching equipment rated to operate within the nominal voltage range of 1 kV1\text{ kV} to 33 kV33\text{ kV}.

24
New cards

Form 4 Separation

An internal partitioning level per I.S. EN 61439 segregating busbars, functional units, and external cable termination points into distinct compartments.

25
New cards

Service Short-Circuit Breaking Capacity (IcsI_{cs})

The fault current a circuit breaker can interrupt repeatedly in test sequences while remaining capable of carrying rated continuous current.

26
New cards

Fault MVA

The prospective apparent short-circuit power of a network, calculated as Fault MVA=3×VL×Ifault1000\text{Fault MVA} = \frac{\sqrt{3} \times V_L \times I_{\text{fault}}}{1000} (equal to 0.693×Ifault [kA]0.693 \times I_{\text{fault}}\text{ [kA]} at 400 V400\text{ V}).

27
New cards

Trip-Free Mechanism

A breaker safety mechanism ensuring the contacts trip open automatically during a fault even if the operating lever is held in the ON position.

28
New cards

Protective Relay

An electrical sensing instrument that monitors circuit variables and automatically energises a breaker trip coil upon detecting an abnormal condition.

29
New cards

Busbar Support

An insulating bracket engineered to mount busbars securely, withstand electromechanical fault forces, maintain dielectric clearance, and accommodate thermal expansion.

30
New cards

Bolt Clamping Force (Friction Grip)

The elastic clamping tension in a tightened bolt that presses joined plates together, using interfacial friction rather than bolt shank shear to transfer loads.

31
New cards

Dyn11 Vector Group

A three-phase transformer connection featuring a delta primary, star secondary with neutral, and secondary voltage leading the primary by 30∘30^\circ.

32
New cards

KNAN Cooling

A transformer cooling class using a less-flammable K-class liquid (fire point >300 ∘C> 300\,^\circ\text{C}) circulating by natural convection with natural air cooling.

33
New cards

Basic Insulation Level (BIL)

A standardised peak impulse voltage rating (kVpkV_p) defining the dielectric capability of equipment to withstand lightning and switching surges.

34
New cards
<p>Motor Protection Circuit Breaker (MPCB)</p>

Motor Protection Circuit Breaker (MPCB)

A specialised circuit breaker for motor branch circuits providing unified protection against sustained thermal overload, short circuits, and phase loss.

35
New cards
<p>Ground Fault Circuit Interrupter (GFCI)</p>

Ground Fault Circuit Interrupter (GFCI)

A fast-acting protective disconnect device commonly installed in moisture-prone domestic areas to cut power upon detecting ground fault currents.

36
New cards
<p>Residual Current Circuit Breaker (RCCB/RCD)</p>

Residual Current Circuit Breaker (RCCB/RCD)

A dedicated residual current device without built-in overcurrent protection that disconnects a circuit when leakage to ground exceeds its sensitivity threshold.

37
New cards

Advantages and disadvantages of copper busbars compared to aluminium busbars in switchboards

Copper offers higher electrical conductivity and superior tensile strength, but is roughly three times denser (heavier) and significantly more expensive than aluminium.

38
New cards

Reason for installing a main backup fuse upstream of MCBs in a domestic consumer unit

Fuses provide high prospective short-circuit breaking capacity (up to 80 kA80\text{ kA}), limiting peak cut-off energy (I2tI^2t) to protect downstream MCBs rated at only 3 kA3\text{ kA} to 6 kA6\text{ kA}.

39
New cards

Process of arc extinction inside an air-break Miniature Circuit Breaker (MCB)

Magnetic fields drive the separating contacts arc into V-splitter plates, which split, cool, and lengthen the arc, driving its voltage above system voltage to extinguish it at current zero.

40
New cards

Operating principles of thermal and magnetic tripping elements in a thermal-magnetic MCB

Thermal tripping relies on an inverse-time bending bimetal strip for sustained overload protection; magnetic tripping uses a current-carrying solenoid for instantaneous short-circuit protection.

41
New cards

Instantaneous trip thresholds and general applications for Type B, C, and D MCBs (BS EN 60898)

Type B trips at 33 to 5×In5 \times I_n (resistive/domestic circuits); Type C trips at 55 to 10×In10 \times I_n (motors/commercial lighting); Type D trips at 1010 to 20×In20 \times I_n (transformers/welders with high inrush).

42
New cards

Calculation of prospective Fault MVA on a 400 V400\text{ V} switchboard with a 25 kA25\text{ kA} prospective fault current

Fault MVA=3×400×25 kA1000=0.693×25 kA=17.325 MVA\text{Fault MVA} = \frac{\sqrt{3} \times 400 \times 25\text{ kA}}{1000} = 0.693 \times 25\text{ kA} = 17.325\text{ MVA}, defining the required minimum breaking capacity.

43
New cards

Distinction between Ultimate Breaking Capacity (IcuI_{cu}) and Service Breaking Capacity (IcsI_{cs})

IcuI_{cu} is the maximum fault current a breaker can interrupt once (may require maintenance), whereas IcsI_{cs} is the fault current it can clear repeatedly while remaining fully operational.

44
New cards

Regulatory requirements for the Main Overcurrent Device (MOD) under NSAI Clause 533.2 / IS 10101

Must be an MCB rated at least 6 kA6\text{ kA} (9 kA9\text{ kA} if <50 kVA< 50\text{ kVA}) in an IP42/IP55 self-extinguishing enclosure with a transparent hinged lid, positioned in the bottom-right of the meter cabinet.

45
New cards

Operational and structural differences between a switch-fuse and a fuse-switch

A switch-fuse has stationary fuses connected in series with separate switch contacts, while a fuse-switch uses the fuse carriers directly as the moving contact blades.

46
New cards

Operating principle and test circuit mechanism of a three-phase Core-Balance RCD

Measures net current sum across supply conductors with a toroidal core to detect earth fault imbalance; pressing the test button connects an internal resistor to simulate a fault and verify tripping.

47
New cards

Five mandatory steps of the Lockout-Tagout (LOTO) procedure on a multi-chamber LV switchboard

  1. Plan the isolation; 2. De-energise and isolate all sources; 3. Apply individual padlocks and warning tags; 4. Discharge stored energy and install barriers; 5. Verify dead with a proved voltage tester.


48
New cards

Internal separation Forms 1 through 4 in switchgear assemblies per I.S. EN 61439

Form 1: No internal separation. Form 2: Busbars separated from units. Form 3: Busbars and individual units separated. Form 4: Busbars, units, and all outgoing cable terminals completely segregated.

49
New cards

How does a unit-type switchboard differ from a cubicle-type switchboard

A unit-type board has individual switch-fuses or MCCBs mounted on a common frame. It is usually cheaper and has less internal separation. A cubicle-type board has floor-standing modular sections bolted together and is commonly used for larger industrial installations.

50
New cards

Why use a sheet-steel switchboard enclosure, and how is its IP rating selected

Steel provides mechanical strength, earth continuity when correctly bonded, and electromagnetic screening. Select the IP rating for the environment. The notes give IP31 for an indoor example, IP54 for dusty conditions and IP65 for water jets.

51
New cards

What access and mounting features are shown in the lecture’s switchboard example

The frame is plumb, level and secured to the floor. The example gives 750 mm rear clearance, doors opening at least 90°, and M12 floor fixings. It also shows lockable handles and a voltage warning. These are figures from the lecture example; actual clearances and fixings depend on the assembly and installation.

52
New cards

Where is the busbar chamber located, and how is access controlled

It is commonly at the top or rear of the switchboard, separated from the cable compartment. Its removable covers require a tool to open.

53
New cards

How are power, control, instrumentation and ESB metering arranged in the example board

Power equipment is near the cable entries. Contactors, relays and timers are grouped in a ventilated control section, with different voltage circuits segregated. Meters and pilot lamps are on the door. ESB metering has a separate sealable CT chamber and meter panel.

54
New cards

Why are the heaviest outgoing loads placed near the incomer?

Their large currents travel through a shorter length of busbar, reducing losses and heating along the board

55
New cards

How does a switch-fuse door interlock work?

The handle mechanism normally prevents the door opening while the switch is ON and prevents switching ON while the door is open.

56
New cards

What is the difference between a mechanical and an electrical interlock?

A mechanical interlock physically prevents an operation. An example is a trapped-key system between mains and generator incomers. An electrical interlock uses a contact in the control circuit to block a closing command until the required condition is met.

57
New cards

Give two advantages of fully insulated busbars

Insulation improves protection against accidental contact and can allow a more compact arrangement. Bare busbars rely on air clearance and barriers. The assembly design determines the permitted spacing.

58
New cards

Why use two spaced busbars per phase or a tubular busbar

Two spaced bars provide more surface area for cooling. A tubular bar puts more conducting material near the surface, where AC current tends to concentrate as conductor size increases.

59
New cards

What do flexible couplers, Belleville washers and phase barriers do

Flexible couplers accommodate movement and thermal expansion. Belleville spring washers help maintain pressure at bolted joints. Phase barriers separate adjacent phases and reduce the risk of accidental bridging.

60
New cards

What affects the continuous current rating of a busbar

Its material, cross-section, arrangement, cooling, ambient temperature and permitted temperature rise. Diversity matters because outgoing circuits may reach their maximum loads at different times.

61
New cards

What are the purposes of a cable gland, an undrilled gland plate and a sealing chamber

A gland secures the cable and maintains the required enclosure protection and armour connection. An undrilled plate allows the correct entry sizes and positions to be made on site. A sealing chamber can restrict water or gas passage where the design calls for it.

62
New cards

What cable-trench dimensions are used in the lecture example?

The example allows the sum of the cable diameters plus 25% spare width, with depths of 600 mm under the floor and 450 mm under walkways, and a chequer-plate cover. Treat these as drawing-specific revision figures.

63
New cards

Where are MCBs, MCCBs and ACBs used, and what current ranges are quoted in the notes?

MCB: final circuits, 6–63 A. MCCB: distribution circuits, 16–1,600 A. ACB: large incomers, 630–6,300 A. These are example ranges and can vary by product.

64
New cards

Why does a large circuit breaker have separate main contacts and arcing contacts?

The main contacts carry normal load current with low loss. The arcing contacts take the arc during switching and protect the main contacts from erosion. The notes give silver alloy for main contacts and tungsten-based material for arcing contacts.

65
New cards

How does a spring-operated circuit breaker close and trip?

A handle or motor charges the closing spring. Releasing it closes the contacts quickly. When the trip mechanism releases the latch, the opening spring separates the contacts.

66
New cards

How can a breaker be controlled locally and remotely?

Local control uses a handle or front-panel pushbuttons. For remote operation, a shunt-trip coil opens the breaker on command. A motor operator or closing mechanism can provide remote closing.

67
New cards

What is discrimination, also called selectivity, between protective devices?

For a fault on an outgoing circuit, the protective device nearest the fault operates while the upstream device stays closed. This keeps healthy circuits supplied. Coordination is checked using device curves and manufacturer selectivity tables

68
New cards

What three things must be checked when selecting a breaker for a switchboard?

Check its continuous current rating against the design load, its breaking capacity against the prospective fault current at its operating voltage, and its coordination with upstream and downstream protection.

69
New cards

Why use an adjustable electronic trip unit on an ACB

It lets the designer set overload pickup, short-time pickup and delay, and instantaneous protection. These settings help coordinate the incomer with outgoing breakers.

70
New cards

How does an oil circuit breaker extinguish an arc?

The contacts open in insulating oil. The arc decomposes some oil and generates gas, mainly hydrogen, which helps cool and de-ionise the arc path. Your existing cards cover the air-break method.

71
New cards

How are the voltmeter, ammeter and kWh meter connected in the example switchboard

The 0–500 V voltmeter connects across the selected phases, directly or through a VT. The 0–5 A ammeter connects to a CT secondary. The kWh meter uses CT current inputs and a voltage input. The notes give class 1.5 for the panel indicators and 1.0 or 0.5 for the energy meter

72
New cards

Name five commissioning checks for a switchboard

Verify busbar joint torque against the manufacturer’s specification, test insulation resistance, verify protection operation by primary injection where specified, check phase rotation, and function-test controls and interlocks.

73
New cards
74
New cards
75
New cards
76
New cards
77
New cards
78
New cards