General & Airframe Oral Questions.

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/147

encourage image

There's no tags or description

Looks like no tags are added yet.

148 Terms

1
New cards

AM.II.H.K6: What type of system is used to indicate the position of the wing flaps?

Usually a resistance-type remote-indicating system suh as the DC Selysyn system.

2
New cards

AM.II.H.K6: What information is shown by the wing flaps position indicator?

The number of degrees the flaps are lowered.

3
New cards

AM.II.H.K7: What are the gyroscopic instruments that are connected to the low-pressure pneumatic system of an aircraft?

Heading indicator, attitude indicator, and turn-of-slip indicator.

4
New cards

AM.II.H.K7: What device is used with a wet-pump vacuum system to prevent oil from getting into the deicer boots?

An oil separator.

5
New cards

AM.II.H.K7: What are two types of filters used with a pressure system for gyros?

A pump inlet filter and an inline filter.

6
New cards

AM.II.H.K7: What type of filter is used with a vacuum system for gyros?

A central air filter.

7
New cards

AM.II.H.K7: What may be causing an attitude indicator to not properly erect or display?

Gyroscopes are dependent on achieving and maintaining proper rotational speed. Failure to do so may be caused by low vacuum created by the vacuum system or motor failure in an electrically-driven gyroscope.

8
New cards

AM.II.J.K2: Where can you find the correct part number for the fuel quantity sensor to be installed in an aircraft in an aircraft fuel tank?

In the IPC dedicated to the aircraft.

9
New cards

AM.II.J.K2: Where are fuel system strainers located?

One strainer is located in the outlet to the tank, and the main strainer is located in the fuel line between of the fuel tank and the inlet to the fuel metering device.

10
New cards

AM.II.J.K2: Why do the fuel strainers used on some turbine-engine aircraft have a warning device that signals the flight crew when the strainers is beginning to clog up?

Strainers clog because ice forms on the filter element. The flight crew can route the fuel through a fuel heater to melt the ice.

11
New cards

AM.II.J.K2: How does water appear in the fuel drainedfrom the tank sumps?

Water appears as a clear globule in the bottom of the container used to collect the fuel drained from the sumps.

12
New cards

AM.II.J.K2: Why must an aircraft fuel valve have a detent in it’s operating mechanism?

The detent gives the pilot a positive indication by feel when the selector valve is in the full ON and full OFF postion.

13
New cards

AM.II.J.K2: What must be done before a fuel selector valve can be removed from an aircraft?

The tank to which the valve is connected must be drained or otherwise isolated?

14
New cards

AM.II.J.K2 What must be done after a fuel valve is replaced?

The fuel system must be checked for leaks.

15
New cards

AM.II.J.K9: What is used as the sensor in the fuel tank for an electronic-type fuel quantity indicating system?

Tubular Capacitors that extend across the fuel tank from top to bottom.

16
New cards

AM.II.J.K9: What is the principle upon which the electronic-type fuel quantity indicating system operates?

Tubular Capacitors extending across the fuel tanks change their capacitance as the fuel level changes.The dielectric constant (k) of the fuel is approximately twice that of air.

17
New cards

AM.II.J.K9: What is used as a sensor in the fuel tank for the older resistance-type fuel quantity indicating system?

A variable resistor with an arm that is moved by a float riding on top of the fuel in the tank.

18
New cards

AM.II.J.K9: What is the purpose of a drip gauge in the fuel tank of a large aircraft?

The drip gauge allows a mechanic to check the fuel level in a tank from the bottom of the tank.

19
New cards

AM.II.J.K9: When must the fuel quantity indicating system indicate “zero”?

During level flight when the fuel in the tank is equal to the unusable fuel supply.

20
New cards

AM.II.L.K4: Are pneumatic deicer boots operated before ice forms or after it has formed?

Pneumatic deicer boots are not operated until ice has formed over them. When the boot inflates, it breaks the ice, and the air flowing over the airfoil blows it away.

21
New cards

AM.II.L.K4: Where does the air come from to operate the pneumatic deicer boots on a reciprocating-engine powered air-plane?

From the discharge side of the air pump used to operate the gyro instrument.

22
New cards

AM.II.L.K4: What is meant by a wet vacuum pump used to power pneumatic deicer boots?

It is a vacuum pump that uses engine oil to lubricate its steel vanes. A dry vacuum pump used carbon vanes. and it does not require any oil for lubrication.

23
New cards

AM.II.L.K4: What is the purpose of the oil separator in a deicer system?

Oil separators are used with wet cauum pumps to remove the lubricating oil from the discharge air before this air is used in the deicer boots.

24
New cards

AM.II.L.K4: How are rubber deicer boots cleaned?

With just mild soap and water.

25
New cards

AM.II.L.K4: How are rubber deicer boots attached to the leading edges of aircraft wings and tail surfaces?

They are bonded to the surface with an adhesive.Boots on older aircraft were attached with machine screws and rivnuts.

26
New cards

AM.II.L.K4: What is the sequence of inflation of a deicing boot system?

There are three tubes in a deicer boots, upper center, and lower. The center tube inflates first with the upper and lower tubes a specified number of seconds later.

27
New cards


AM.II.N.K5: What is meant by a fully articulated rotor system?

It is a rotor system in which the individual blades are free to flap, drag, and feather.

28
New cards

AM.II.N.K5: What is meant by a semirigid rotor system?

A two-blade rotor system in which the blades can feather, but cannot flap or drag. The rotor hub is mounted on the mast with a teetering hinge that allows the entire rotor to rock as a unit.

29
New cards

AM.II.A.K5: What type of device is a Cleco fastener?

A patented fastener that is inserted in the rivet holes and used to hold two pieces of sheet metal together until they can be riveted.

30
New cards

AM.II.A.K5: What type of rivet may be used to replace a round head rivet in an aircraft structure?

A universal head rivet.

31
New cards

How long should a rivet be to join two pieces of sheet metal?

The combined thickness of the metal sheets plus 1½ x the rivet shank DIA.

32
New cards

AM.II.A.K5: How can rivets be physically identified for part number and type of material?

The identifying mark on the head of an aluminum alloy rivet indicates the specified alloy used in the manufacture of the rivet.

33
New cards

AM.II.C.K11: What is a stabilator?

A singel-piece horizontal tail surface that acts as both the horizontal stabilizer and the elevators. A stabilator pivots about its front spar.

34
New cards

AM.II.C.K11: What is meant by differential aileron travel?

Aileron movement in which the upward-moving aileron deflects a greater distance than the one moving downward. the up aileron produces parasite drag to counteract the induced drag produced by the down aileron.

35
New cards

AM.II.C.K11: What is a Frise aileron?

An aileron with its hinge line set back from the leading edge so that when it is deflected upward, part of the leading edge projects below the wing and produces parasite drag to help overcome adverse yaw.

36
New cards

AM.II.C.K11: What is a ruddervator?

Movable control surfaces on a V-tail airplane that are controlled by both the rudder pedals and the control yoke. When the yoke is moved in or out, the ruddervators move together and act as the elevators. When the rudder pedals are depressed, the ruddervators move differentially and act as a rudder.

37
New cards

AM.II.C.K11: What is the function of the ailerons on an airplane?

Ailerons rotate the airplane about its longitudinal axis.

38
New cards

AM.II.D.K1: If a mechanic gives a 100-hour inspection to an aircraft that proves to be un-airworthy, what must the mechanic give the owner or operator of the aircraft?

A signed and dated list of all the discrepancies that keep aircraft from being airworthy.

39
New cards

AM.II.D.K1: Where can you find the recommended statement to use for recording the approval or disapproval of an aircraft for return to service after a 100-hour inspection?

Title 14 CFR 43.11.

40
New cards

AM.II.D.K1: Under what conditions can an aircraft be operated with a 100 hour inspection overdue?

The aircraft ca be operated fro no more than 10 hours after an inspection is due fro the purpose of flying it to a place where the inspection can be performed.

41
New cards

AM.II.D.K1: For how long can an aircraft be operated if a 100-hour inspection is overdue?

For no more than 10 hours. The time beyond the 100 hours must be subtracted from the time before the next inspection is due.

42
New cards

AM.II.D.K1: Under what conditions can an aircraft that is due for an annual inspection be operated?

It can only be flown when a special flight permit is issued.

43
New cards

AM.II.D.K1: What certification is required for a mechanic to be able to approve an aircraft for return to service after a 100 hour inspection?

An Aviation Mechanic certificate with Airframe and Powerplant ratings.

44
New cards

AM.II.D.K1: What determines whether or not an aircraft must be given a 100-hour inspection?

Aircraft that carry persons for hire and aircraft that are used for flight instruction for hire must be given 100-hour inspection.

45
New cards

AM.II.D.K1: What is the difference between an annual inspection and a 100-hour inspection?

The inspections themselves are identical. An annual inspection can be conducted only by an A&P mechanic with an Inspection Authorization (IA), versus a 100-hour inspection can be performed by a regular A&P mechanic without additional license.

46
New cards

AM.II.D.K1: What certification is required for a mechanic to conduct an annual inspection and approve the aircraft for return to service after the inspection?

An Aviation Mechanic certificate with Airframe and Powerplant ratings and an Inspection Authorization.

47
New cards

AM.II.D.K1: What is a progressive inspection?

An inspection of the same level as an annual inspection but approved by the FAA to be performed on a schedule that does not require the aircraft to be out of service fro the time necessary to perform the entire inspection all at once.

48
New cards

AM.II.E.K2: What absorbs the taxi shocks in an oleo shock strut?

The compressed air or nitrogen.

49
New cards

AM.II.E.K2: How much air or nitrogen should be put into an oleo shock strut?

With the strut serviced with fluid and the filler plug in place and the weight of the aircraft on the strut, put in enough air or nitrogen to extend the piston to the height specified in the aircraft maintenance manual.

50
New cards

AM.II.E.K2: What is the purpose of using an exerciser Jack when servicing a shock strut with fluid?

The jack moves the piston up and down inside the cylinder to work all of the air out of the oil to be sure that the proper amount of oil is in the strut.

51
New cards

What is a squat switch and where is it located?

AKA, Weight-on-Wheels, is a landing gear safety switch that energizes a circuit to prevent the landing gear retraction handle from being moved to the “RETRACT” position when weight is on the landing gear. It is located in the torsion links of one of the main landing gears.

52
New cards

AM.II.E.K2: What kind of device is normally used as a sensor to detect the condition of a retractable landing gear?

A precision microswitch.

53
New cards

AM.II.E.K2: What is the purpose of the centering cam in a nose-wheel shock strut?

The centering cam forces the nose wheel straight back with the strut before is it retracted into the nose-wheel well.

54
New cards

What absorbs the initial landing impact in an oleo shock strut?

The transfer of oil from one compartment to another through a metered orifice.

55
New cards

AM.II.F.K1: What kind of filter is a micronic filter?

A filter with a special paper element.

56
New cards

AM.II.F.K1: What is a double-action pump?

A pump that delivers fluid with the movement of the pump handle in both directions.

57
New cards

AM.II.F.K1: Why do most engine-driven hydraulic pumps have a shear section in their drive coupling?

If the pump should seize, the shear section will break, disconnecting the pump from the engine and preventing further damage.

58
New cards

AM.II.F.K1: What are the two basic types of hydraulic fluid used in modern aircraft?

Mineral base fluid and phosphate ester base fluid.

59
New cards

AM.II.F.K1: Does the main hydraulic pump take its fluid from the bottom of the reservoir, or from a standpipe?

The main pump normally takes its fluid from a standpipe, while the emergency pump takes its fluid from the bottom of the reservoir. If a break in the system should allow the main pump to pump all of its fluid overboard, there will still be enough fluid in the reservoir to allow the emergency system to extend the landing gear and actuate the brakes.

60
New cards

AM.II.F.K1: Why are some hydraulic reservoirs pressurized?

Pressurization ensures that fluids will be supplied to the inlet of the pumps at high altitude where there is not enough atmospheric pressure to do this.

61
New cards

AM.II.F.K1: What are two ways aircraft hydraulic reservoirs may be pressurized?

By an aspirator in the fluid return line or by bleed air from one of the engine compressors.

62
New cards

AM.II.F.K1: What is used to flush a hydraulic system that uses Skydrol hydraulic fluid?

Trichlorethylene or a solvent recommended by the aircraft manufacturer.

63
New cards

AM.II.F.K1: What is used to flush a hydraulic system that uses mineral base hydraulic fluid?

Naptha, varsol, or Stoddard solvent.

64
New cards

AM.II.F.K1: Where can you find the type of hydraulic fluid required for a particular aircraft?

In the maintenance manual for the aircraft. This information is also on a placard on the system reservoir.

65
New cards

AM.II.F.K1: What type of pump is a gear pump considered?

A gear pump is a constant displacement, high pressure pump.

66
New cards

AM.II.F.K1: What type of pump is a piston pump with a variable cam plate considered?

Fuel pumps may be divided into two distint system categories:

  1. Constant displacement

  2. Variable displacement

A piston pump with a variable cam changes the effective (not actual) length of each piston stroke. This makes this type of pump a variable displacement with constant pressure.


67
New cards

AM.II.G.K7: Where does the warm air come from that is used to heat the cabin of a large jet transporter aircraft?

Warm engine compressor bleed air is used.

68
New cards

AM.II.G.K7: Where is the first place hot compressor bleed air gives up some its heat in an air-cycle cooling system?

In the primary heat exchanger.

69
New cards

AM.II.G.K7: What is the function of the air-cycle machine in an air-cycle cooling system?

The centrifugal compressor increases the pressure and temperature of the bleed air. This high temperature air gives up some of its heat in the secondary heat exchanger, and a great deal more as it draws the expansion turbine. It leaves the expansion turbine as cold air.

70
New cards

AM.II.G.K7: Why must air-cycle conditioning systems incorporate a water separator?

The rapid cooling of the air in the expansion turbine causes moisture to condense in the form of fog. This moistture is trapped in the moisture separator before the air is released into the cabin.

71
New cards

AM.II.G.K7: How is the temperature of the air produced by an air-cycle cooling system controlled?


END OF AIRFRAME

By a temperature control valve which mixes hot engine compressor bleed air with cold air from the expansion turbine.


END OF AIRFRAME

72
New cards

What is the formula for power in a DC circuit?

Power = Voltage times current (P = E x I)

73
New cards

AM.I.A.K12: What is the relationship between mechanical and electrical power?

1 horse power = 746 watts

74
New cards

AM.I.A.K12: What is meant by true power in an AC circuit?

The product of the circuit voltage and the current that us in phrase with this voltage.

75
New cards

AM.I.A.K12: In what units is true power expressed?

In watts.

76
New cards

AM.I.A.K12: What is meant by apparent power in an AC circuit?

The product of the circuit voltage and the circuit current, without reference to phase angle.

77
New cards

AM.I.A.K12: In what units is apparent power expressed?

In volt-amps.

78
New cards

AM.I.A.K12: What is meant by reactive power in an AC circuit?

The power consumed in the inductive and capacitive reactance in an AC circuit. Reactive power is also called wattless power.

79
New cards

AM.I.A.K12: In what units is reactive power expressed?

In volt-amps reactive (VAR), or kilovolt-amps reactive (KVAR).

80
New cards

AM.I.A.K12: What is meant by power factor in an AC circuit?

The ratio of true power to apparent power. It is also the ratio of circuit resistance to circuit impedance.

81
New cards

How many watts of power are consumed by a 1/5 horsepower, 24-volt DC motor that is 75% efficient?

Power efficiency is expressed as


Efficiency = power out/ power in


Power consumed is the same as Power In, and 1 horsepower (HP) equals 746 watts. Therefore,


Power In = Power Out/Efficiency

82
New cards

AM.I.A.K15: What is meant by the capacity rating of a lead-acid battery?

The number of hours a battery can supply a given current flow.

83
New cards

AM.I.A.K15: What electrolyte is used in a lead-acid battery?

A mixture of sulfuric acid and water.

84
New cards

AM.I.A.K15: Does the specific gravity of the electrolyte in alead-acid battery increase or decrease as the battery becomes discharged?

It decreases.

85
New cards

AM.I.A.K15: What is the specific gravity of a fully charged lead-acid battery?

Between 1.275 and 1.300.

86
New cards

AM.I.A.K15: How many cells are there in a 24-volt lead-acid battery?

12 cells.

87
New cards

AM.I.A.K15: What is the range of temperatures of the electrolyte in a lead-acid battery that does not require a correction when measuring its specific gravity.

Between 70° F and 90° F.

88
New cards

AM.I.A.K15: How do you treat a lead-acid battery compartment to protect it from corrosion?

Paint it with asphaltic (tar-base) paint or with a polyurethane enamel.

89
New cards

AM.I.A.K15: What is used to neutralize spilled electrolyte from lead-acid battery?

Baking soda (bicarbonate of soda) and water solution.

90
New cards

AM.I.A.K15: How high should the electrolyte level be in a properly serviced lead-acid battery?

Only up to the level of the indicator in the cell.

91
New cards

AM.I.A.K15: How high should the electrolyte level be in a properly serviced lead-acid battery?

Only up to the level of the indicator in the cell.

92
New cards

AM.I.A.K15: Why is the closed-circuit voltage of a lead-acid battery lower than its open-circuit voltage?

Voltage is dropped across the internal resistance of the battery.

93
New cards

AM.I.A.K15: What gases are released when a lead-acid battery is being charged?

Hydrogen (H) and oxygen (O)

94
New cards

AM.I.A.K15: What is the electrolyte used in a nickel-cadmium battery?

Potassium hydroxide and water.

95
New cards

AM.I.A.K15: Why is a hydrometer not used to measure ethe state of charge of a nickel-cadmium battery?

The electrolyte of a nickel-cadmium battery does not enter in the chemical changes that occur when the battery is charged or discharged. Its specific gravity does not change appreciable.

96
New cards

AM.I.A.K15:Is the electrolyte level of a nickel-cadmium battery lowest when the battery is fully charged or fully discharged?

Fully discharged.

97
New cards

AM.I.A.K15: What is a result of cell imbalance in a nickel-cadmium battery?

The low internal resistance allows current to flow between the unbalanced cells and generate heat.

98
New cards

AM.I.A.K15: What is a thermal runaway?

The large current flow allowed by the low internal resistance causes the cells produce more heat than they can dissipate. The heat further lowers the resistance so more current can flow: this continues until the battery self destructs.

99
New cards

AM.I.A.K15: How may thermal runaway be prevented?

By carefully monitoring the temperature of the cells and controlling the charging current to prevent an excess of current flowing into the battery.

100
New cards

AM.I.A.K15: How is it possible to know when a nickel-cadium battery is fully charged?


Completely discharge the battery and give it a constant-current charge to 140% of its ampere-hour capacity.