Chapter 8 - Fire Pump Characteristics

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/49

encourage image

There's no tags or description

Looks like no tags are added yet.

50 Terms

1
New cards

The centrifugal pump on fire apparatus serves as a:

Non-positive displacement pump

2
New cards

A centrifugal pump contains an impeller assembly with the impeller riding on:

Wear rings

3
New cards

In a centrifugal pump, the passage for water that enlarges as it nears the discharge outlet of the pump is the:

Volute

4
New cards

Under certain conditions, ___ lock occurs, and a centrifugal pump will not develop discharge pressure with air in the pump

Air

5
New cards

The fire service employs 3 types of centrifugal pumps: single-stage, two-stage, and

Ganged

6
New cards

The single-stage fire pump is sometimes known as the:

Double-suction impeller

7
New cards

Water enters both eyes of the single-stage impeller in order to cancel:

Lateral thrust

8
New cards

The stripping edges in the opposed discharge volutes divert water into two streams ___ degrees apart:

180

9
New cards

Two-stage centrifugal pumps can switch from volume to pressure mode by use of a:

Transfer valve

10
New cards

The process of switching a centrifugal pump between pressure and volume is known as:

Changeover

11
New cards

Switching a two-stage centrifugal pump from volume to pressure:

Can double the discharge pressure

12
New cards

In a two-stage centrifugal pump, the D/O must not exceed a NPDP of ___ when switching between pressure and volume modes

50psi (350 kPa)

13
New cards

What type of valve is essential to the operation of a two-stage centrifugal fire pump?

Clapper

14
New cards

Fire pumpers that must supply sprinklers and standpipes in high-rise buildings may use a single-stage, high-pressure centrifugal pump when discharge pressures are higher than ___

250psi (1750 kPa)

15
New cards

What is the term used when no water flows from the discharge side of the pump, possibly resulting in pump damage?

Deadheading

16
New cards

Newer model centrifugal pumps may come with a thermal relief valve that allows overheated water to circulate:

Between the pump and the main water tank

17
New cards

To seal the impeller shaft on a centrifugal pump, manufacturers use:

Packing rings

18
New cards

On a midship pumper, power reaches the pump that is located in line behind the engine and transmission through a:

Split-shaft transfer case

19
New cards

Fire pumps can be configured to operate over a range of capacities determined by the piping arrangement and the:

Apparatus gear ratio

20
New cards

To prevent an automatic transmission gear selector from moving during a pumping operation or a manual transmission from slipping out of gear:

There is a lock on the transmission or shift lever

21
New cards

The collar that slides across a saft in a midship transfer case may not make it across due to misaligned or mushroomed teeth, known as a ___ condition

But-tooth

22
New cards

A power take off (PTO) pump is powered by the vehicle’s transmission through a(n):

Idler gear

23
New cards

When using a PTO pumper during pump-and-roll operations and supplying hoselines, the D/O should drive the vehicle while monitoring the:

Pressure gauge

24
New cards

Pumpers with a rear-engine PTO (REPTO) design are powered by:

The engine’s flywheel

25
New cards

Fire department pumpers with a front mounted pump:

Are susceptible to freezing

26
New cards

Apparatus with rear-mount pumps offer key advantages such as more usable compartment space and:

Even weight distribution

27
New cards

Pumps powered by a gasoline or diesel engine independent of the vehicle drive engine are known as a(n):

Auxiliary pump

28
New cards

Located on the pump operator’s panel, a meter that helps in monitoring the vehicle’s electrical system along with a voltmeter is the:

Ammeter

29
New cards

The master intake gauge is also known as a(n):

Compound gauge

30
New cards

During drafting, pump capacity is reached when the vacuum gauge reaches:

20 in (-70 kPa)

31
New cards

When operating the pump with water from a hydrant or a supply line from another pumper, the master intake gauge will show:

Residual pressure

32
New cards

Te master pump discharge gauge reflects:

Overall discharge pressure

33
New cards

According to NFPA 1900, pumpers with a tank capacity equal to or greater than 500 gal (2000 L) should be able to flow at least:

500gpm (2000 L/min) or capacity of the pump, whichever is less

34
New cards

What is the device in modern pumps that will prevent damage to the pump if the tank-to-pump valve is open when the pump receives water under pressure?

Check valve

35
New cards

On pump intakes, as the piping nears the pump, it typically tapers to a(n) ___ shape to eliminate the vortices that may occur in water that flows through circular piping

Square

36
New cards

Based on NFPA 1900, a sufficient number of ___ discharge openings must be provided to flow the rated capacity of the pump

2.5in (65mm)

37
New cards

The most common type actuator for ball-type valves on pump discharges are push-pull handles and handles that are:

Quarter turn

38
New cards

NFPA 1900 requires all intakes and discharges that are 3in (77mm) or greater to be equipped with:

Slow-acting controls

39
New cards

On a pressure governor, RPM/Throttle mode is used when:

Drafting or supplying water

40
New cards

The electronic pressure governor features cavitation protection by returning the engine to idle when the intake pressure falls below:

30 psi (210 kPa)

41
New cards

In a discharge relief valve, the slave valve is controlled by a spring-loaded:

Pilot valve

42
New cards

Intake relief valves open when the intake pressure rises above the required operating pressure by more than:

10 psi (70 kPa)

43
New cards

The type of pump used for drafting is a:

Positive displacement pump

44
New cards

The pump manufacturer’s operating manual should specify the preferred RPM for priming, but generally, the range is:

1000 - 1200 RPM

45
New cards

A pump cooler valve recirculates water from the discharge of the pump to the:

Pump intake

46
New cards

A type of auxiliary cooler on a pumper that uses small tubes surrounded by a water jacket connected to the discharge of the fire pump is the:

Marine cooler

47
New cards

If a pump cannot develop the necessary pressure or flow, it may be due to:

Worn wear rings

48
New cards

According to NFPA 1900, pressure control devices must control discharge pressure within:

30 psi (210 kPa)

49
New cards

NFPA 1900 and 1910 specify that a fire pump in good condition will achieve at least __ in Hg of vacuum

22

50
New cards

According to NFPA 1900, the accuracy points for discharge gauges on a fire pump are:

1050 kPa, 1400 kPa, and 1750 kPa