Commercial Driver's License Pre-Trip Inspection

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/21

flashcard set

Earn XP

Description and Tags

Comprehensive practice flashcards covering tractor-trailer pre-trip inspection procedures, component criteria, in-cab checks, air brake test steps, and exterior lighting requirements.

22 Terms

1
New cards

When inspecting the alternator or water pump belt, how much deflection indicates that the belt is excessively loose?

Deflection of more than 12 inch\frac{1}{2}\,\text{inch} to 34 inch\frac{3}{4}\,\text{inch} when pushed by hand indicates excessive looseness.

2
New cards

How are the air compressor and power steering pump driven on the engine?

Both the air compressor and power steering pump are gear driven.

3
New cards

When pulling the slack adjuster and pushrod by hand with the brakes released, what is the maximum distance the pushrod should move?

The pushrod should move no more than approximately 1 inch1\,\text{inch}.

4
New cards

What is the minimum acceptable tire tread depth for the front steering tires?

A minimum tread depth of 432 inch\frac{4}{32}\,\text{inch}.

5
New cards

What is the minimum acceptable tire tread depth for the rear drive axle and trailer tires?

A minimum tread depth of 232 inch\frac{2}{32}\,\text{inch}.

6
New cards

What three emergency equipment items must be verified during the in-cab inspection?

A securely mounted and properly charged fire extinguisher, 33 reflective warning triangles, and spare electrical fuses.

7
New cards

What must be verified regarding the gap between the trailer apron and fifth wheel skid plate?

The trailer must lie flat on the fifth wheel skid plate with no space between the apron and the skid plate.

8
New cards

What condition must the fifth wheel release arm and safety latch be in during coupling inspection?

The release arm must be secure, all the way in (engaged position), and the safety latch must be in place.

9
New cards

What is the purpose of ensuring the sliding fifth wheel is locked in the proper position?

To ensure that the tractor frame will clear the trailer landing gear during turns.

10
New cards

What do rust trails radiating from the wheel lug bolt holes indicate?

Rust trails or distortion around the bolt holes indicate that the lug nuts or rim may be loose from the wheel.

11
New cards

What are the inspection criteria for dual wheel Budd spacing?

The wheels must be evenly spaced, not damaged, and free of foreign objects.

12
New cards

What are the inspection requirements for the trailer landing gear?

It must be fully raised with no missing parts, the crank handle must be secure, and the support frame and landing pads must not be damaged.

13
New cards

What should be observed regarding the transmission gear and ABS indicator during a safe start?

The gear must be in neutral when turning the key on; if the ABS light stays on, the ABS system needs to be serviced.

14
New cards

At what pressure range should the air compressor build up to the governor cut-off?

Between 120 PSI120\,\text{PSI} and 140 PSI140\,\text{PSI}.

15
New cards

How is the service brake check performed to ensure proper operation?

Pull forward at 5 mph5\,\text{mph}, apply the service brake, and stop, verifying that the vehicle does not pull to either side and stops properly.

16
New cards

What is Step 1 of the air brake check (leaks and pressure drop test)?

With pressure at governor cut-off (120 PSI120\,\text{PSI} to 140 PSI140\,\text{PSI}), turn the engine off, switch the key to on without starting, hold the brake pedal for 1 minute1\,\text{minute}, verify pressure drops no more than 4 PSI4\,\text{PSI}, and listen for leaks.

17
New cards

At what air pressure should the low air warning light and buzzer activate during Step 2 of the air brake check?

At approximately 55 PSI55\,\text{PSI} while fanning the brake pedal.

18
New cards

At what air pressure should the tractor protection valve and parking brake valve pop out during Step 3 of the air brake check?

At approximately 40 PSI40\,\text{PSI} while continuing to fan the brake pedal.

19
New cards

How is the tractor parking brake tug test performed?

With air pressure at governor cutout, the parking brake engaged, and the trailer brakes released, verify the brake holds by gently attempting to pull forward.

20
New cards

Which lights and signals must be inspected on the front of the tractor?

High and Low beams, Clearance Lights, Left and Right turn signals, and 4-way flashers.

21
New cards

Which lights and signals must be inspected on the rear of the trailer?

Clearance Lights, Left and Right turn signals, 4-way flashers, Brake Lights, and Taillights.

22
New cards

Which lights and signals are inspected on the front of the trailer?

Clearance Lights.