Industrial Arts Reviewer: Woodworking, Drafting, Plumbing, Electrical, Electronics, Automotive, Refrigeration, and Metalwork

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/66

flashcard set

Earn XP

Description and Tags

Comprehensive practice flashcards defining essential terminology, materials, tools, defects, and systems across industrial arts disciplines.

67 Terms

1
New cards

Yakal

A hardwood that withstands heavy mechanical stress, frequent use, and occasional moisture better than decorative woods; suitable for workshop worktables and bridge posts.

2
New cards

Pressure-reducing valve

A plumbing valve installed to maintain a lower downstream pressure despite a higher upstream supply pressure, protecting fixtures and fittings from damage.

3
New cards

Plumb bob

A weighted tool suspended from a string used by carpenters to check and correct vertical alignment, such as ensuring wall studs do not lean.

4
New cards

Concrete

A composite construction material produced by combining cement, water, fine aggregates (sand), and coarse aggregates (gravel).

5
New cards

Cement

The active binding ingredient in concrete that, when mixed with water and aggregates, hardens to hold the composite mixture together.

6
New cards

Miter joint

A woodworking joint formed by cutting two mating boards at equal angles, typically 45∘45^\circ, to form a corner such as a 90∘90^\circ window or picture frame.

7
New cards

Honeycombing

An internal seasoning defect characterized by internal cracks within lumber that are not visible on the surface, caused by drying lumber too rapidly or unevenly in a kiln.

8
New cards

Cutting-plane line

A drafting line that identifies where an imaginary cutting plane passes through an object to display its internal construction in a sectional view.

9
New cards

P-trap

A curved plumbing fitting installed beneath sinks that retains a water seal to prevent foul sewer gases and odors from entering the room.

10
New cards

Header

A masonry brick laid across a wall course so that its short end face is exposed.

11
New cards

Stretcher

A masonry brick laid lengthwise along a wall course so that its long face is exposed.

12
New cards

Class AA concrete mix

A specific structural concrete mixture proportioned at a volumetric ratio of 1:112:31:1\frac{1}{2}:3 (cement, sand, and gravel).

13
New cards

Flemish bond

A decorative masonry brickwork bond pattern that alternates headers and stretchers within every individual course; generally weaker than English bond.

14
New cards

English bond

A strong masonry brickwork pattern consisting of alternating entire courses of stretchers and entire courses of headers.

15
New cards

Stretcher bond

A brickwork layout pattern using staggered stretchers exclusively, commonly used for non-load-bearing partition walls.

16
New cards

Plane

A woodworking hand tool used to shave and smooth uneven wooden surfaces while maintaining a true, flat working face.

17
New cards

Hidden line

A medium-weight technical drawing line consisting of evenly spaced short dashes, used to depict interior edges and surfaces not visible to the eye.

18
New cards

Center line

A technical drafting line consisting of alternating long and short dashes, used to represent the axis of symmetry or the rotational center of cylindrical parts.

19
New cards

Dovetail joint

A high-tensile woodworking joint featuring interlocking wedge-shaped pins and tails, designed specifically to resist tensile or pulling forces in assemblies like drawer fronts.

20
New cards

Cedar

A cone-bearing softwood known for its natural resistance to insect attack, decay, and rot; frequently chosen for mountain cabin shingles and posts.

21
New cards

Knot

A natural wood defect consisting of a hard, circular cross-section embedded in lumber where a tree branch was once connected to the main trunk.

22
New cards

Efflorescence

A masonry defect visible as a white, powdery crystalline deposit of salts on concrete or brick surfaces, occurring when internal moisture dissolves soluble salts and evaporates.

23
New cards

Curing

The essential concrete maintenance process of providing adequate moisture, temperature, and time during early hardening to prevent rapid drying and surface cracking.

24
New cards

Tee

A T-shaped plumbing fitting used to connect a branch pipeline perpendicular to a straight main line while permitting uninterrupted continuous flow through the main pipe.

25
New cards

Lap joint

A woodworking joint formed by removing half the thickness from two overlapping members so that their joined surfaces lie completely flush.

26
New cards

Pine

A lightweight, economical softwood from cone-bearing trees, widely utilized for interior wall framing and lightweight partitions due to its easy workability.

27
New cards

Dowel joint

A joint formed by inserting cylindrical wooden pegs coated in adhesive into matching bored alignment holes between two pieces of wood.

28
New cards

Gate valve

A plumbing valve designed primarily for fully open or fully closed service; not engineered to regulate flow or throttle pressure gradually.

29
New cards

Mortar

A workable mixture composed of cement, fine aggregates (sand), and water, utilized to bind concrete blocks, bricks, and stones together and fill gaps between courses.

30
New cards

Molave

A durable, dense hardwood renowned for exceptional natural resistance to termite attack, rot, and moisture, making it ideal for outdoor posts.

31
New cards

Burl

A rounded abnormal knot-like wood growth featuring highly distorted and irregular grain patterns, prized for ornamental furniture and decorative veneers.

32
New cards

Angle valve

A specialized shut-off valve commonly positioned underneath plumbing fixtures like lavatories and toilets to isolate the fixture's water supply during maintenance.

33
New cards

Twist grain

A natural wood defect caused by spiral growth of fibers around a tree trunk, which makes boards prone to tear-out and difficult to plane smoothly.

34
New cards

Warp

A wood distortion defect resulting from uneven drying, causing faces or edges of a board to curve, cup, or twist away from a flat plane.

35
New cards

Galvanized Iron pipe (GI pipe)

A metallic plumbing pipe that is no longer preferred for modern potable water installations due to susceptibility to internal rust accumulation and progressive corrosion.

36
New cards

Narra

A premium locally recognized hardwood renowned for its strength, rich grain, durability, and finishing qualities in fine cabinetry and flooring.

37
New cards

Parallel circuit

An electrical circuit where components are connected across the same common voltage nodes, allowing independent device operation and equal supply voltage across all branches.

38
New cards

Series circuit

An electrical circuit where components are linked end-to-end along a single path; the same current flows through all devices, and an open circuit at one point shuts down all loads.

39
New cards

Toughness

The mechanical property of a metal enabling it to absorb heavy impacts, shock loads, and mechanical energy without fracturing or cracking.

40
New cards

Capacitor

A passive electrical/electronic component specifically constructed to store electric charge and electrostatic energy temporarily within an electric field.

41
New cards

Compressor

The mechanical pump in a vapor-compression refrigeration system that draws in low-pressure vapor and increases both its pressure and temperature for delivery to the condenser.

42
New cards

Crankshaft

An engine mechanical component that converts the reciprocating (up-and-down) linear motion of the pistons into rotational motion to drive a vehicle.

43
New cards

Diode

A two-terminal semiconductor device that permits electric current to pass freely in only one forward direction while blocking it in reverse.

44
New cards

Evaporator

A refrigeration heat exchanger where low-pressure liquid refrigerant absorbs thermal energy from the refrigerated space and boils into a vapor.

45
New cards

Automotive Thermostat

A temperature-sensitive valve that controls engine coolant flow to the radiator; if stuck open, coolant continuously circulates immediately after cold start, causing poor heating.

46
New cards

Transistor

A three-terminal semiconductor device capable of acting as an electrically controlled solid-state switch or an amplifier of electrical current.

47
New cards

Condenser

A heat-rejecting component in a refrigeration cycle where high-pressure vapor releases heat to the surrounding environment and condenses into a liquid.

48
New cards

Ignition coil

An inductive step-up electrical transformer in a gasoline ignition system that converts 12 V12\,\text{V} from the battery into thousands of volts to produce a spark at the spark plugs.

49
New cards

Multimeter

A versatile electrical diagnostic instrument capable of measuring multiple electrical properties including voltage, current, and resistance.

50
New cards

Malleability

The mechanical property of a metal that allows it to be hammered, rolled, or pressed into thin sheets without tearing or cracking.

51
New cards

Ductility

The mechanical property of a metal that enables it to be pulled or drawn out under tensile stress into long, thin wires without rupturing.

52
New cards

Expansion valve

A refrigeration throttling device that meters the flow of refrigerant into the evaporator while drastically reducing its pressure and temperature.

53
New cards

Rat-tail splice

An electrical wire splice formed by twisting the ends of two or more conductors together, commonly executed inside electrical junction boxes.

54
New cards

Brass

A non-ferrous, corrosion-resistant alloy composed primarily of copper and zinc, easily worked into tubing, musical instruments, and decorative hardware.

55
New cards

Alternator

An automotive mechanical-electrical generator that produces electric power to run vehicle accessories and maintain the charge of the battery while the engine runs.

56
New cards

Thermal expansion

The physical property that causes metal materials to expand in volume and length when exposed to heat and shrink back upon cooling.

57
New cards

Tap splice

An electrical splicing technique used to join a branch conductor to a continuous running main conductor without cutting the main line.

58
New cards

Cavalier oblique

A pictorial drafting projection where the frontal face is parallel to the picture plane, receding axes are inclined at 45∘45^\circ, and depths are shown at full measured scale.

59
New cards

Isometric drawing

An axonometric pictorial projection where the three coordinate axes appear equally foreshortened, with two receding axes angled at 30∘30^\circ to the horizontal.

60
New cards

Shock absorbers

Hydraulic suspension components engineered to damp spring oscillations, reduce body bounce, and dissipate mechanical vibration when driving over rough road surfaces.

61
New cards

Western Union splice

A traditional, mechanically strong inline wire splice used to connect two solid electrical conductors end-to-end to extend the length of a wire.

62
New cards

Fuel filter

A fuel delivery system component responsible for trapping dirt, rust, and contaminants before fuel reaches the fuel pump and fuel injectors.

63
New cards

Split

A severe lumber drying defect characterized by a crack or fissure extending all the way through the thickness of a board from one surface to the opposing face.

64
New cards

Shake

A natural wood defect involving a complete separation between growth rings or wood fibers that develops internally while the living tree is still standing.

65
New cards

Check

A wood seasoning defect characterized by small, shallow surface cracks that occur along the grain but do not pass through the full thickness of the timber.

66
New cards

Voltage

The potential difference or electrical pressure existing between two points that drives an electrical current through a closed circuit.

67
New cards

Brittleness

The mechanical property of a material, such as cast iron, causing it to fracture suddenly under stress without exhibiting noticeable bending, stretching, or plastic deformation.