1/52
Looks like no tags are added yet.
no matter how fast a reaction is, it cannot continue beyond what point
the point of chemical equilibrium
Keq » 1
equilibrium favors products
Keq « 1
equilibrium favors reactants
Keq = 1
both reactants and products are present at equilibrium
ΔH < 0
exothermic reaction
Keq decreases with increasing T
ΔH > 0
endothermic reaction
Keq increases with increasing T
ΔGrxn
standard free energy change (kJ/mol)
ΔHrxn
standard enthalpy change (kJ/mol)
ΔSrxn
standard entropy change (kJ/mol-K)
Van’t Hoff equation
ln Keq = - ΔGrxn/RT = - ΔHrxn/R + ΔSrxn/R
optimal operating temperatures must balance…
equilibrium conversion against enzyme stability
theoretical yield
amount product formed / amount reactant used for that product o
observed yield
amount product present / amount reactant consumed
gross yield
amount product present / amount reactant provided
why are there three different types of yield
competing reactions consume reactant without producing desired product
incomplete conversion leaves unreacted reactant
product degradation consumes the product after its formed
total rate RA
mass of moles converted per unit time
volumetric rate rA
rate per unit volume
specific rate rA
rate per unit catalyst
arrhenious equation
k = Ae-E/RTu
units of k for zero order
concentration/time
units of k for first order
1/time
units of k for second order
1/(concentration x time)
why is drawing tangents by hand considered unreliable for determining reaction rates
they are subjective
small errors translate into large errors
no error estimate
two methods for determining reaction rates
equal-area method
midpoint method
Km is a measure of
enzyme affinity for substrate
lower Km =
higher enzyme affinity
low substrate, s « Km
kinetics are first order in s
high substrate, s » Km
kinetics are zero order in s
intermediate substrate, s = Km
mixed order kinetics, M-M equation needed
what is the point of Michaelis-Menten kinetics
bridging zero and first order kinetics
michaelis menten plot
direct plot of v versus s
useful for visualizing data but not for precise parameter estimation
Lineweaver-burk plot
1/v versus 1/s
distorts experimental error, not recommended for accurate work
most commonly used
Eadie Hofstee plot
v/s versus v
distorts errors, reduced accuracy compared to langmuir plot
Langmuir plot
s/v versus s
minimizes distortion of error, recommended for accurate determination of vmax and Km
what type of data is preferred for enzyme kinetic analysis
initial rate data
mass transfer
the movement of a chemical species from one location to another due to a concentration gradient and/or advection
in which direction does mass naturally diffuse
from high to low concentration regions
ficks law
JA”= - DAB dCA/dx
negative sign indicates diffusion occurs from high to low concentration
JA”
molar diffusive flux of A (mol/m2s)
DAB
diffusion coefficient of A in B (m2/s)
is a material property similar to thermal conductivity
depends on temperature, pressure, and the species involved
Ficks law is similar in structure to which other law
Fouriers law
diffusion coefficients (DAB) differences by state of matter
gases are about 104 times larger than liquids, and 1010 times larger than in solids
higher temperature means what for the diffusion coefficient
higher diffusion coefficient
why do gases diffuse faster than liquids, and liquids faster than solids?
gas molecules are farther apart and move more rapidly
liquid molecules are densely packed
solid molecules are locked in a lattice, diffusion requires defects
in composite diffusion, which layer controls the overall permeation rate
the layer with the highest resistance
relationship between diffusion and solubility
P = DAB x S
what factors influence mass transfer by convection
fluid velocity, flow regime, geometry, fluid properties
St
Stanton number
Stm
stanton number for mass transfer
Pr
prandtl number
Sc
schmidt number
Cf
fraction coefficient
Sh
Sherwood number