1/49
Looks like no tags are added yet.
Definition of ILS
Instrument Landing System: an electronic system that provides both horizontal and vertical guidance to a specific runway, used to execute a precision instrument approach procedure
ILS Approach Category Minimums: CAT I
-decision height 200 feet and runway visual range 2400 (with touchdown zone and centerline lighting RVR 1800 feet)
ILS Approach Category Minimums: CAT II
-decision height 100 feet and RVR 1200 feet
ILS Approach Category Minimums: CAT IIIa
-no decision height or DH below 100 feet and RVR not less than 700 feet
ILS Approach Category Minimums: CAT IIIb
-no DH or DH below 50 feet and RVR less than 700 feet but not less than 150 feet
ILS Approach Category Minimums: CAT IIIc
No DH and no RVR limitation
When is special authorization/equipment required for ILS?
CAT II and III approaches
ILS IAP: Operational Tips
-make small corrections, continue instrument cross-check and interpretation
-set CRS OBS to the front course when flying inbound on the back course
-intercept glideslope at the altitudes specified on the published approach chart
-remember the CDI sensing is shaper and faster on the LOC course than VOR
ILS Components
-localizer: provides horizontal guidance
-glideslope: provides vertical guidance, usually at a 3° slope
-marker beacons: provides range information along the approach path
-approach lights: assists in the transition from instrument to visual flight
ILS airborne components
airborne equipment for the ILS system includes receivers for respective indicator instruments
-localizer: typical VOR receiver is also a localizer receiver and functions the same
-glideslope: tuned automatically to the proper frequency when the localizer is tuned
-marker beacons: outer, middle, inner, and back course
-NAVAID (receivers): DME, ADF
Localizer (LOC)
-located on the extended centerline
-provides horizontal guidance along the centerline of the runway
-provides course guidance between 108.1 and 111.95 MHz (odd tenths only)
-the unit radiates a field pattern, developing a course down the centerline of the runway in both directions (front course and back course)
Localizer Identification
-facility is audibly identified by a three-letter designator transmitted at frequent regular intervals
-the ILS identification is preceded by the letter “I” (two dots)
Localizer Coverage Range
-35° up to 10NM to each side of the centerline for the 10NM
-10° up to 18NM from the antenna of 4,500 feet above the elevation of the antenna site
Localizer Course Width
-defined as angular displacement, based on runway dimensions
-course width is based on runway dimensions
-course width varies between 3° to 6° tailored to provide 700’ at threshold.
threshold full scale limit is always 700 feet
normally 5°, high needle sensitivity
full scale deflection 2.5° to either side of the centerline
4x more sensitive than VOR
-with no more than ¼ scale deflection, the airplane will be aligned with the runway
Localizer Principle
-the unit sends out two different modulation frequencies (90 Hz, 150 Hz)
-CDi displays the course deflection based on the frequency module (both front and back courses)
Localizer Error: Reverse Sensing
-occurs when flying inbound on the back course
-occurs when flying outbound on the front course
-heading corrections to on-course are made opposite the needle deflection
Localizer Error: Reverse Sensing Corrective Action “Fly Away from the Needle”
-set CRS OBS to the front course when flying inbound on the back course
-back course signals should not be used for an approach unless a back course approach procedure is published and authorized by ATC
Glideslope
– A part of the ILS that projects a radio beam upward at an angle of approximately 3° from the approach end of an instrument runway to provide vertical guidance for final approach toward the runway touchdown point
– The course projected by the GS equipment is essentially the same as would be generated by a localizer operating on its side
– The unit only radiates signal in the direction of the final approach on the front course.
• Housed in a building 750 to 1,250 feet down the runway.
• Located between 400 and 600 feet to one side of the centerline.
• No back course.
Glideslope Transmitter
– The GS transmitter radiates signals only in the direction of the final approach on the front course.
• No vertical guidance for approaches on the back course
– The glidepath is normally 1.4° thick.
• Full deflection is 0.7° on either direction.
– At 10 NM from the point of touchdown, this represents a vertical distance of approximately 1,500 feet, narrowing to a few feet at touchdown
ILS Errors: False Glideslope
-GS facilities inherently produce additional courses at higher vertical angles
-these false courses occur at approximately 9-12 degrees
-false courses can result in a reversed GS needle indication
False Glideslope: Preventative Action
-conduct the approach at the altitudes specified on the published approach chart
ILS Errors-Reflection Error
– Localizer and GS signals are subject to the same type of bounce from hard objects as space waves.
– Surface vehicles and even other aircraft flying below 5,000 feet AGL may disturb the signal for aircraft on the approach.
ILS Component: Marker Beacon
Provides range information over specific points along the approach.
– Used along the flightpath when approaching an airport for landing, marker beacons indicate, both aurally and visually, when the aircraft is directly over the facility.
-types:
outer marker
middle marker
inner marker
back-course marker
Outer Marker
-located on the localizer front course 4-7 miles from the airport
-indicates a position at the appropriate altitude that will intercept the glidepath
Middle Marker
-located on the localizer front course 3500 feet from the landing threshold
-to indicate a position where the GS centerline is about 200 feet above the touchdown zone elevation
Inner Marker
-located on the localizer front course between the MM and landing threshold
-to indicate the point at which an aircraft is at the decision height on the glidepath during a CAT II ILS approach
Back-Course Marker
-to indicate the back-course final approach fix
Marker Beacon: Compass Locator
-low powered NDBs
-received and indicated by the ADF receiver (non-radar method of finding the localizer)
-when used in conjunction with an ILS front course, the compass locator facilities are collocated with the OM and/or MM facilities
-compass locator is not always present in all ILS systems
ILS- Approach Lighting System (ALS)
-approach lighting system provides lights that will penetrate the atmosphere far enough from touchdown to give directional, distance, and glidepath information for safe visual transition
-visual stage of the instrument approach
-assist in the transition from instrument to visual flight
-approach should be continued by reference to the runway touchdown zone markers
Localizer Type Directional Aid (LDA)
The localizer type directional aid (LDA) is of
comparable utility and accuracy to a localizer.
– Not part of a complete ILS.
– Course width is between 3° and 6°.
– More precise approach course than an SDF installation.
– Some LDAs are equipped with a glideslope (GS).
The LDA course is not aligned with the runway
– Straight-in minimums may be published if the angle between
the runway centerline and the LDA course does not exceed 30°.
– If this angle exceeds 30°, only circling minimums are
published.
Simplified Directional Facility (SDF)
The simplified directional facility (SDF) provides a
final approach course similar to the ILS localizer.
– SDF may or may not be aligned with the runway and the
course.
– SDF may be wider than a standard ILS localizer.
– The angle of convergence of the final approach course
and the extended runway centerline must not exceed 30°
SDF (Coverage Range)
– Usable off-course indications are limited to 35° either side of the course centerline.
– Must provide distances of 18 NM covering a sector 10° either side of centerline up to an angle
7° above the horizontal.
– The course width of the SDF signal emitted from the transmitter is fixed at either 6° or 12°.
• Less precise than a standard ILS localizer.
Holding- Definition
A predetermined maneuver that keeps aircraft within a specified airspace while awaiting further clearances from ATC
Standard Holding Pattern
right turns
Inbound leg time at or below 14000MSL
1 min
Inbound leg time above 14000 feet MSL
1 ½ mins
outbound leg of holding pattern
-timing begins over/abeam the fix, whichever occurs later
-if the abeam position cannot be determined, start timing when turn to outbound is completed
which leg do you adjust time/heading
outbound
Maximum holding airspeeds
MHA- 6000’: 200 KIAS
6001-14000’: 230 KIAS
14001’: 265 KIAS
3 holding entry procedures
parallel, teardrop, direct entry
Parallel Entry
– Fly to the fix
– Turn to a heading to the outbound course
– Fly outbound for 1 minute
– Turn in the direction of the holding pattern
– Return to the holding fix
• Or intercept the holding course inbound
Teardrop Entry
– Fly to the fix
– Turn outbound to a heading for a 30° teardrop entry
• Within the pattern (in the protected area)
– Fly for a period of 1 minute
– Turn in the direction of the holding pattern
• To intercept the inbound holding course
Direct Entry
-fly direct to fix
-turn to following the holding pattern
ATC clearance infromation- where pattern is not charted
-direction of holding
-holding fix
-radial
-leg length
-direction of turn
-when to expect further clearance
ATC Clearance- Charted hold
“hold [cardinal direction] as published”
When to slow to holding airspeed
3 minutes prior to crossing holding fix
Bank angle during hold
standard
can a symmetrical pattern be flown with wind?
nope, you need to correct for wind
how to compensate for wind effect?
-calculate wind correction angle on inbound leg, APPLY on OUTBOUND leg
-when outbound, triple the inbound drift
Types of ALS
ALSF-2
ALSF-1
MALSR/SSALSR
MALSF
REIL
ODALS