Introduction to Electrical and Electronics Engineering

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/51

flashcard set

Earn XP

Description and Tags

Comprehensive vocabulary flashcards covering basic electrical quantities, circuit laws, AC/DC waveforms, semiconductor diodes, rectifiers, BJTs, operational amplifier architectures, digital logic gates, flip-flops, and microcontroller systems.

52 Terms

1
New cards

Electric Charge (QQ)

A measure of the number of free electrons, measured in Coulombs (C\text{C}), where 1 C1\,\text{C} is equal to 2π×10182\pi \times 10^{18} electrons (each electron carries a charge of −1.602×10−19 C-1.602 \times 10^{-19}\,\text{C}).

2
New cards

Electromotive Force (EMF)

The property of a physical device that causes electrical charge to move or tend to move in a particular direction, symbolized by EE and measured in Volts (V\text{V}).

3
New cards

Electric Current (II)

The rate at which electric charges move through a surface, given by i=dqdti = \frac{dq}{dt} and measured in Amperes (A\text{A}).

4
New cards

Ohm's Law

The law stating that, temperature remaining constant, the current through a conductor between two points is directly proportional to the potential difference across those points (V=IRV = IR).

5
New cards

Conductance (GG)

The reciprocal of electrical resistance (G=1RG = \frac{1}{R}), expressed in units of Siemens (S\text{S}).

6
New cards

Kirchhoff's Current Law (KCL)

The principle stating that the algebraic sum of currents entering a node is zero, or the sum of currents entering a node equals the sum of currents leaving the node.

7
New cards

Kirchhoff's Voltage Law (KVL)

The principle stating that the algebraic sum of voltages around any closed loop is zero, or the sum of voltage rises equals the sum of voltage drops around the loop.

8
New cards

Ideal Voltage Source

An active element that maintains a prescribed terminal voltage regardless of the current drawn by the circuit, characterized by an internal resistance of Rs=0 ΩR_s = 0\,\Omega.

9
New cards

Ideal Current Source

An active element that maintains a prescribed terminal current regardless of the voltage across its terminals, characterized by an internal resistance of Rs=∞R_s = \infty.

10
New cards

Voltage Divider Rule

A formula used to calculate the voltage drop across any single series resistor: Vout=RnR1+R2+⋯+RnEV_{out} = \frac{R_n}{R_1 + R_2 + \dots + R_n} E, valid only when the same current flows through all resistors.

11
New cards

Current Divider Rule

A formula used to determine branch currents in a two-branch parallel network: I1=Itotal(R2R1+R2)I_1 = I_{total} \left(\frac{R_2}{R_1 + R_2}\right) and I2=Itotal(R1R1+R2)I_2 = I_{total} \left(\frac{R_1}{R_1 + R_2}\right).

12
New cards

Root Mean Square (RMS) Value

The effective value of an alternating current that produces the same amount of heat in a given resistance as a direct current flowing through the same resistance; for a sine wave, IRMS=Im2I_{RMS} = \frac{I_m}{\sqrt{2}}.

13
New cards

Form Factor

The ratio of the RMS value to the average value of an alternating waveform, equal to 1.111.11 for a sinusoidal waveform and 1.571.57 for a half-wave rectified waveform.

14
New cards

Peak Factor (Crest Factor)

The ratio of the maximum (peak) value to the RMS value of a waveform, equal to 2≈1.414\sqrt{2} \approx 1.414 for a sinusoidal waveform.

15
New cards

p-Type Material

A semiconductor material created by doping an intrinsic crystal with trivalent impurity atoms (such as boron, gallium, or indium) which act as acceptor atoms and establish holes as majority carriers.

16
New cards

n-Type Material

A semiconductor material created by introducing pentavalent impurity atoms (such as antimony, arsenic, or phosphorus) which act as donor atoms and establish electrons as majority carriers.

17
New cards

Depletion Region

A region formed around a p-n junction void of free charge carriers, created by the recombination of diffusing electrons and holes and populated by immobile positive and negative ions.

18
New cards

Thermal Voltage (VTV_T)

A temperature-dependent voltage parameter defined by VT=kTKqV_T = \frac{k T_K}{q}, where at 27∘C27^\circ\text{C} (300 K300\,\text{K}), VT=25.875 mV≈26 mVV_T = 25.875\,\text{mV} \approx 26\,\text{mV}.

19
New cards

Knee Voltage (VKV_K)

The threshold forward-bias voltage required for significant conduction in a diode, equal to approximately 0.3 V0.3\,\text{V} for Germanium (Ge), 0.7 V0.7\,\text{V} for Silicon (Si), and 1.2 V1.2\,\text{V} for Gallium Arsenide (GaAs).

20
New cards

Reverse Saturation Current (IsI_s)

The small drift current that flows across a reverse-biased p-n junction due to minority charge carriers crossing the depletion region, largely independent of the applied reverse voltage.

21
New cards

Shockley's Diode Equation

The equation defining diode current in forward- and reverse-bias regions: ID=Is(eVD/(nVT)−1)I_D = I_s \left(e^{V_D / (n V_T)} - 1\right), where nn is the ideality factor.

22
New cards

Half-Wave Rectifier (HWR)

A rectifier circuit utilizing a single diode that conducts during only one half-cycle of the input AC supply, producing a pulsating DC output with a rectification efficiency of 40.5%40.5\% and a ripple factor of 1.211.21.

23
New cards

Full-Wave Bridge Rectifier

A rectifier circuit employing four diodes in a bridge arrangement that conducts on both alternating half-cycles, achieving a rectification efficiency of 81.16%81.16\% and a ripple factor of 0.4820.482.

24
New cards

Bipolar Junction Transistor (BJT)

A three-terminal, current-controlled semiconductor device formed by two back-to-back p-n junctions that utilizes both electrons and holes as charge carriers.

25
New cards

BJT Region Doping Profile

In a BJT, the emitter is heavily doped, the base is lightly doped, and the collector is moderately doped; the physical size ratio of the transistor to base is 150:1150:1, and outer to central layer doping ratio is 10:110:1.

26
New cards

Active Region (BJT)

The region of transistor operation where the base-emitter junction is forward-biased and the collector-base junction is reverse-biased, enabling the device to function as an amplifier with IC=βIBI_C = \beta I_B.

27
New cards

Saturation Region (BJT)

The operating region where both the base-emitter and collector-base junctions are forward-biased, causing collector-to-emitter terminals to behave as a closed switch with maximum current flow.

28
New cards

Cutoff Region (BJT)

The operating region where both the base-emitter and collector-base junctions are reverse-biased, resulting in nearly zero terminal currents and causing the transistor to act as an open switch.

29
New cards

Common Base Current Gain (αdc\alpha_{dc})

The ratio of the collector current to the emitter current in the DC common-base configuration (αdc=ICIE\alpha_{dc} = \frac{I_C}{I_E}), typically ranging from 0.900.90 to 0.9980.998.

30
New cards

Common Emitter Current Gain (βdc\beta_{dc})

The ratio of the collector current to the base current in the DC common-emitter configuration (βdc=ICIB\beta_{dc} = \frac{I_C}{I_B}), typically ranging from 5050 to over 400400.

31
New cards

Quiescent Point (Q-Point)

The fixed DC operating point of a transistor defined by specific steady-state values of ICI_C and VCEV_{CE} when no alternating input signal is applied.

32
New cards
<p>Operational Amplifier (Op-Amp)</p>

Operational Amplifier (Op-Amp)

A high-gain direct-coupled differential amplifier integrated circuit characterized by extremely high input impedance and low output impedance, capable of executing mathematical and signal conditioning operations.

33
New cards
<p>LM741 Pin Configuration</p>

LM741 Pin Configuration

An 8-pin dual in-line package (DIP) op-amp where Pin 1 and Pin 5 are offset null, Pin 2 is inverting input, Pin 3 is non-inverting input, Pin 4 is −Vsupply-V_{supply}, Pin 6 is output, Pin 7 is +Vsupply+V_{supply}, and Pin 8 is NC (no connection).

34
New cards

Common-Mode Rejection Ratio (CMRR)

A figure of merit measuring an op-amp's ability to reject common-mode noise while amplifying differential signals, defined as the ratio of differential voltage gain to common-mode voltage gain (CMRR=AdAc\text{CMRR} = \frac{A_d}{A_c}).

35
New cards

Virtual Ground

A condition in an inverting op-amp circuit with negative feedback where the inverting terminal is maintained at virtually zero potential (0 V0\,\text{V}) without being physically connected to ground, due to near-infinite open-loop gain.

36
New cards

Inverting Amplifier

An op-amp closed-loop configuration where the input signal is applied to the inverting terminal, yielding an amplified output that is 180∘180^\circ out of phase with a voltage gain of Av=−RfR1A_v = -\frac{R_f}{R_1}.

37
New cards

Non-Inverting Amplifier

An op-amp configuration where the input signal is connected directly to the non-inverting terminal, producing an amplified in-phase output with a voltage gain of Av=1+RfR1A_v = 1 + \frac{R_f}{R_1}.

38
New cards

Summing Amplifier

An inverting op-amp circuit that produces an output proportional to the negative weighted algebraic sum of multiple input voltages: Vo=−(RfR1V1+RfR2V2+⋯+RfRnVn)V_o = -\left(\frac{R_f}{R_1} V_1 + \frac{R_f}{R_2} V_2 + \dots + \frac{R_f}{R_n} V_n\right).

39
New cards

Differential Amplifier (Subtractor)

An op-amp circuit that amplifies the voltage difference between two input signals; when matched such that R1R2=R3R4\frac{R_1}{R_2} = \frac{R_3}{R_4}, the output is Vo=R3R1(V2−V1)V_o = \frac{R_3}{R_1}(V_2 - V_1).

40
New cards
<p>Op-Amp Differentiator</p>

Op-Amp Differentiator

A circuit featuring a series input capacitor and a feedback resistor that generates an output voltage directly proportional to the time rate of change of the input: vo(t)=−RCdv1(t)dtv_o(t) = -RC \frac{dv_1(t)}{dt}.

41
New cards
<p>Op-Amp Integrator</p>

Op-Amp Integrator

A circuit featuring an input resistor and a feedback capacitor that produces an output voltage proportional to the time integral of the input signal: vo(t)=−1RC∫v1(t) dtv_o(t) = -\frac{1}{RC} \int v_1(t)\,dt.

42
New cards

Binary Number System

A base-2 numbering system that uses only two digits, 0 and 1 (radix 2), where each column represents an increasing power of 2 from the least significant bit (LSB) to the most significant bit (MSB).

43
New cards

Universal Logic Gate

A logic gate (specifically NAND or NOR) that can be combined and configured to implement any of the basic boolean operations (NOT, AND, OR) without requiring any other gate type.

44
New cards

Exclusive-OR (XOR) Gate

A derived digital logic gate whose output is HIGH (1) if and only if one of its inputs is HIGH; if both inputs are identical (both 0 or both 1), the output is LOW (0).

45
New cards

De Morgan's Laws

Fundamental boolean theorems stating that the complement of a sum equals the product of the complements (P+Q‾=P‾⋅Q‾\overline{P + Q} = \overline{P} \cdot \overline{Q}) and the complement of a product equals the sum of the complements (P⋅Q‾=P‾+Q‾\overline{P \cdot Q} = \overline{P} + \overline{Q}).

46
New cards

Sequential Logic Circuit

A digital circuit whose output depends on both past inputs (stored internal memory states) and present inputs, typically requiring a clock signal for synchronization.

47
New cards

SR Flip-Flop

A basic bi-stable sequential circuit with Set (SS) and Reset (RR) inputs; setting S=1,R=1S=1, R=1 produces an invalid/unpredictable output known as a race-around condition.

48
New cards

D Flip-Flop

A clocked data storage flip-flop that transfers the logical value of its single input (DD) directly to output (QQ) upon the clock pulse transition, eliminating the race condition present in SR flip-flops.

49
New cards

JK Flip-Flop

A universal flip-flop design that eliminates the invalid state of the SR latch; when both JJ and KK inputs are held HIGH, the output toggles state on each clock edge.

50
New cards

Asynchronous Counter (Ripple Counter)

A sequential binary counter circuit in which the clock pulse is connected only to the first flip-flop, with each successive flip-flop triggered by the output of the preceding stage.

51
New cards

Synchronous Counter

A binary counter circuit where all constituent flip-flops are triggered simultaneously by a single common clock pulse, eliminating accumulated ripple propagation delays.

52
New cards
<p>8051 Microcontroller Architecture</p>

8051 Microcontroller Architecture

A classic single-chip microcomputer integrated circuit featuring an on-chip CPU, 4 kB4\,\text{kB} ROM, 128 Byte128\,\text{Byte} RAM, two 16-bit timers/counters (Timer 0 and Timer 1), interrupt control, and four 8-bit I/O ports (P0, P1, P2, P3).