1/40
Vocabulary practice flashcards covering states of matter, phase diagrams, partition coefficients, rheology, and interfacial phenomena in pharmaceutics.
Gases
The state of matter characterized by the highest kinetic energy, no fixed shape or volume, particles in constant motion, and the weakest intermolecular interactions.
Liquids
The state of matter characterized by moderate kinetic energy, a fixed volume while taking the shape of the container, slight compressibility, and moderate to strong intermolecular interactions.
Solids
The state of matter characterized by the lowest kinetic energy, fixed shape and volume, incompressibility, and the strongest intermolecular interactions.
Crystalline solids
Solids characterized by a regular, repeating 3D arrangement of lattice units throughout the crystal, which possess a sharp and well-defined melting point.
Polymorphs
Chemical entities, including pharmaceutical agents, that may exist in more than one crystalline structure.
Hydrates
Forms that result when water is incorporated into the crystal lattice.
Solvates
Forms that result when a solvent is incorporated into the crystal lattice.
Salt crystals
Solids formed when a weak acid or base reacts with a counterion to yield a salt that interacts with the lattice, formed to enhance solubility.
Cocrystals
A homogeneous, multicomponent phase of fixed stoichiometry where chemical entities are held together in a crystal lattice by intermolecular forces; useful when an ionizable group is not available.
Amorphous solids
Solids that lack long-range order and exhibit a random molecular arrangement.
Supercritical fluids
Fluids created to achieve better solvent capacity, higher diffusivity, and lower viscosity.
Arms of a ternary phase diagram
The boundaries of the triangle that represent a combination of two out of the three components.
Area within a ternary phase diagram
The interior of the triangle that represents all possible combinations of the three components of the system.
log(P)=0
A partition coefficient value representing equal distribution of the drug in both phases.
log(P)>0
A partition coefficient value indicating that the drug is lipid soluble.
log(P)<0
A partition coefficient value indicating that the drug is water soluble.
True partition coefficient
A partition coefficient that considers only the unionized form of the molecule.
Apparent partition coefficient
A distribution coefficient that includes both ionized and unionized forms of the molecule.
Non-ionized preservative form
The active chemical form required for preservative efficacy because the ionized form cannot penetrate the lipophilic outer membrane of a microorganism.
Newtonian fluid
A fluid in which viscosity remains constant regardless of the applied shear stress or shear rate.
Non-Newtonian fluid
A fluid possessing a viscosity that changes depending on the applied shear rate or shear stress.
Plastic flow
A non-Newtonian flow behavior where no flow occurs in response to shear stress until a certain transition point is reached.
Pseudoplastic flow
A non-Newtonian flow behavior characterized by instantaneous flow under applied stress, where viscosity decreases as shear rate increases.
Dilatant flow
A non-Newtonian flow behavior where the fluid flows at low stress and becomes more resistant with agitation, meaning viscosity increases with shear rate.
Thixotropy
A time-dependent shear-thinning property in which a material becomes more fluid with increasing time of applied force.
Rheopexy (Rheopecty)
A time-dependent property characterized by an increase in viscosity, where a material becomes more viscous with increasing time of applied force.
Surface tension
The force per unit length that exists at the boundary between a liquid and a gas.
Interfacial tension
The resistance to mixing or adhesion due to differences in molecular attraction on either side of an interface.
Spreading coefficient (S)
A parameter that determines spreading ability; if positive, the liquid spreads easily, but if negative, it will not spread easily and remains as a droplet.
Wettability
The ability of a liquid to maintain contact with a solid surface, or its tendency to spread on a surface and remain in contact with it.
Contact angle (θ)
The angle formed between the edge of a liquid droplet and the solid surface it sits on, used to estimate the extent of wetting.
Complete wetting
A wetting condition where θ=0∘ and the liquid spreads fully over the solid surface.
Poor wetting
A wetting condition where θ>90∘ and the liquid forms a droplet or beads up.
Zeta potential
The electrical potential at the boundary where the moving fluid layer attached to a particle separates from the bulk liquid.
Adsorption
The process by which atoms, ions, or molecules from a substance adhere to the surface of another substance, typically a solid or a liquid.
Surfactants
Amphiphilic molecules containing both a hydrophilic head and a hydrophobic tail that reduce surface and interfacial tension by aligning at phase boundaries.
Critical micelle concentration (CMC)
The concentration at which a surfactant begins forming micelles in solution.
Anionic surfactants
Surfactants whose polar head carries a negative charge; often possess an unpleasant taste, can cause skin irritation, and are incompatible with cationic surfactants (e.g., sodium lauryl sulfate).
Cationic surfactants
Surfactants whose polar head carries a positive charge; utilized as antimicrobial (bactericidal) agents and incompatible with anionic surfactants (e.g., quaternary ammonium compounds such as benzalkonium chloride).
Nonionic surfactants
Surfactants whose polar head has no electrical charge, making them insensitive to salts or pH changes (e.g., oil-soluble SPAN and hydrophilic TWEEN).
Zwitterion surfactants
Surfactants containing two ionizable groups (one cationic and one anionic) that can be cationic, anionic, or both depending on pH; mainly used as cosurfactants (e.g., Dipalmitoylphosphatidylcholine [DPPC]).