1/23
Vocabulary flashcards covering phase equilibria, vapor pressure calculations, Clausius-Clapeyron relation, reaction Gibbs free energy, binary phase diagrams, solder alloy selection criteria under RoHS, and SI derived units from CHEM 4331 Physical Chemistry I Exam II.
Mutual Phase Equilibrium
The thermodynamic state in which the temperature, pressure, and chemical potential (μ) of each component are equal across all coexisting phases.
Solid-Gas Coexistence Line
The phase boundary on a pressure-temperature phase diagram along which the chemical potential of the solid equals the chemical potential of the gas (μsolid=μgas) at each point.
Vapor Pressure Lowering (Weak Monoprotic Acid)
The decrease in pure solvent vapor pressure upon adding a nonvolatile solute; pure water vapor pressure of 23.76torr at 25∘C drops to 23.52torr in an aqueous solution of weak monoprotic acid at XHA=0.010.
Isomer Equilibrium (n-butane and iso-butane)
The chemical equilibrium state where more iso-butane than n-butane is present at 25∘C, driven by iso-butane's more negative standard Gibbs energy of formation (ΔfG∘=−17.97kJ/mol versus −15.71kJ/mol for n-butane).
Boiling Point of Pure Component A
The vaporization temperature of pure component A at system pressure, identified as 50∘C on the binary temperature-composition phase diagram.
Boiling Point of Pure Component B
The vaporization temperature of pure component B at system pressure, identified as 10∘C on the binary temperature-composition phase diagram.
Lever Rule
The graphical method for determining phase proportions on a phase diagram; at 30∘C and overall composition XA=0.4 with vapor at XA=0.36 and liquid at XA=0.64, it yields 0.04nvap=0.24nliq, meaning there are 6mol of vapor for every 1mol of liquid.
Total Vapor Pressure (Ptot)
The total equilibrium pressure of a binary ideal solution given by Ptot=XAPA∗+XBPB∗, which equals 350Torr for 1mol of A (PA∗=200Torr) and 3mol of B (PB∗=400Torr) at 50∘C.
Vapor Phase Mole Fraction (yA)
The mole fraction of volatile component A in the gas phase in equilibrium with a liquid mixture, determined by Dalton's law as yA=PtotPA=350Torr50Torr≈0.143.
Enthalpy of Vaporization (ΔvapH)
The heat required to vaporize one mole of liquid substance, calculated using the Clausius-Clapeyron equation to be 32.3kJ/mol for benzene between 25∘C (0.13atm) and normal boiling point 80.2∘C (1atm).
Standard Gibbs Energy of Reaction (ΔrG∘)
The change in free energy under standard conditions, calculated by ΔrG∘=−RTln(Kp), which equals 17.3kJ/mol at 394.8∘C (667.8K) for the decomposition of COCl2(g) into CO(g) and Cl2(g) (Kp=0.0444).
European Union RoHS Directive
The European Union Reduction of Hazardous Substances directive mandating that electronics be manufactured without lead (Pb), eliminating traditional Sn-Pb solders.
Sn/Ag Solder System
A lead-free solder alloy recommended under RoHS that forms a eutectic at approximately 3.5% mass Ag (96.5% mass Sn) with a melting temperature of approximately 225∘C, falling below the component failure limit of 250∘C.
Au/Sn Solder System
A solder system exhibiting a eutectic transition at approximately 94% mass Au with a melting point of approximately 211∘C.
Pascal (Pa)
The SI derived unit of pressure, equivalent to 1kgm−1s−2 or 1Nm−2.
Joule (J)
The SI derived unit of energy, equivalent to 1kgm2s−2, 1Nm, or 1Pam3.
Watt (W)
The SI derived unit of power, equivalent to 1kgm2s−3 or 1Js−1.
Molar Gas Constant (R)
The fundamental physical constant with values of 8.31447JK−1mol−1, 8.31447×10−2LbarK−1mol−1, and 8.20574×10−2LatmK−1mol−1.
At two points A and B on the slid gas phase transition line on the phase diagram
The u of the solid is equal to the u (chemical potential ) of the gas at each point
Two phases are considered to be in mutual equilibrium when
The temperature, pressure and chemical potential of each component are the same in each phase.
The vapor pressure of pure water at 25 c is 23.76 torr which value represents the vapor pressure of a nonvolatile weak monoprotic acid at a concentration Xha=0.010
23.52 torr
The delta f G values for n btane and isobutane at 25 c are… (n-butane=-15 and isobutane butane=-17)when an equimolar mixture of n-butane and isobutane-butane is allowed to attain an equilibrium state between the two isomers
More isobutane than n-butane is present.

Label the regions of the phase diagram (BP of pure a and pure b and if the overall composition of A was 0.4 wht is the composition of each of the phases at 30 c
Boiling point of A - 50 c
Boiling point of B- 10 c
Nvap “ vap = n liq l liq n(0.4-0.36) =0.04 N n liq (0.64-0.4)
0.36 vapor
0.64 liquid
and 0.24/0.04=6 so there are 6 mols of vapor for 1 mol of liquid

The european union RoHs derevtive h mandated all electronics be lead fre…
Sn/Ag - reccomend, promising eutectic at 3.5% c
Ag/cu - do not recommend, high mp
Bi/pb- do not recommend. Contains lead
Ag/sn- recommend (possible phase transition below 50C) 94% mass Au and 210 C melting