1/37
Flashcards covering aircraft fabric covering materials, terms, installation methods, testing procedures, dope finishing systems, and troubleshooting defects.
Fabric Coverings Advantage & Disadvantages
The primary advantage of fabric covering on an aircraft is its light weight, while its two primary disadvantages are flammability and lack of durability.
Nitrate Dope
A mixture of cellulose dissolved in nitric acid used as a fabric coating that provides superior adhesion, fabric encapsulation, and tightening over the frame, but is extremely flammable.
Butyrate Dope
A fabric coating mixture of cellulose dissolved in butyric and acetic acids that protects against dirt and moisture with lower flammability than nitrate dope, but weaker initial adhesion to fabric.
Aluminum Solids
Particles added to butyrate dope coatings to reflect sunlight and block ultraviolet (UV) radiation from penetrating the fabric and degrading the aircraft structure.
Plasticizers
Dope additives developed to keep dried dope coatings flexible and prevent embrittlement.

Fabric Weave Orientations
The structural directions of woven aircraft fabric, including the warp (longitudinal/parallel to selvage), fill or weft (perpendicular at 90×), and bias (45× diagonal).
Warp
The dominant direction of woven fibers running parallel to the selvage edge of the roll, having more filaments per bundle than fill or bias fibers.
Weft (Fill)
The fibers running perpendicular (90×) to the warp and selvage edge, which tie in the warp fibers to create the weave.
Bias
The diagonal fiber direction running at a 45× angle to the warp fibers in both positive and negative directions.
Selvage Edge
The manufactured edge on a roll of woven fabric that prevents unraveling and serves as a physical reference line for warp direction.
Pinked Edge
A fabric edge cut in a series of continuous V-shapes to prevent unraveling and provide increased surface area for gluing to structures.
Threads Per Inch (TPI)
A measurement of weave density that determines the amount of stress a fabric can withstand and where it can be used on an aircraft.
Nap
Short fiber ends protruding from the surface of fabric that must be trimmed off rather than pulled.
Envelope Method
A fabric application process where a pre-sewn fabric envelope is slipped over the aircraft structure and attached by cementing or hand sewing.
Blanket Method
A fabric application method where fabric sheets are wrapped around a structure and attached at trailing edges or longerons.
Grade A Cotton
An organic aircraft fabric weighing 4.5 oz/sq yd with a thread count of 80×84 per inch and a new material tensile strength of 80 lb/in.
Mercerization
A process of treating cotton under tension with Sodium Hydroxide (Caustic Soda) followed by an acid neutralization bath to swell fibers, increase strength and luster, improve dye affinity, and pre-shrink the material.
Irish Linen
A natural fabric made from flax with a new tensile strength of 140 lb/in that is shrunk using water and is primarily used in aircraft restoration.
Polyester Fabric
A synthetic aircraft covering available in 3.7 oz, 2.7 oz, and 1.7 oz weights that replaced organic fabrics in the 1950s and is heat-shrunk using an iron set to 240×F.
Reinforcing Tape
A tape with a strength of 150 lb per 1/2 in width applied over rib caps after fabric installation to protect fabric from rib lacing attachments.
Anti-Chafe Tape
Self-adhesive cloth tape applied to sharp protrusions, rib caps, and metal seams prior to fabric installation to prevent tearing.
Rib Bracing Tape
Tape woven spanwise around alternating top and bottom rib caps prior to fabric installation to hold wing ribs in proper alignment.

Surface Tape
Polyester or cotton finishing tape applied over seams, ribs, patches, and edges after fabric installation.
Drain Grommets
Plastic doughnut-shaped rings attached to the undersides of wings, control surfaces, and fuselages to allow internal drainage and prevent moisture condensation.

Inspection Ring
A plastic ring doped onto fabric to form structural support for an inspection opening in a fabric wing.

Airworthy Fabric Condition
The condition in which aircraft fabric retains at least 70× of the original breaking strength required for aircraft certification.
Test Strip Method
A destructive fabric test where a 141 in by 4–6 in sample is cut from an exposed surface, unraveled to a 1 in width, stripped of coatings, and pulled with weights until failure.

Punch Tester (Seyboth Tester)
A non-destructive fabric tester featuring red (weak), yellow (stronger), and green (good) color bands used to gauge fabric serviceability.
Maule Tester
A spring-loaded device calibrated in breaking strength used to test fabric serviceability directly on an aircraft without punching holes or cutting test strips.
Rand-O-Proof G-6302
A non-tautening nitrate-based dope formulated for use as a penetrating first coat on polyester fabric or cotton.
Super Seam Fabric Cement
A high-solids, nitrate-based adhesive used to secure Ceconite fabric to structures.
Ringworm
A circular cracking pattern formed in weathered, brittle dope finishes as plasticizers deteriorate over time.
Rejuvenator
A solvent and plasticizer mixture (such as Butysolv) sprayed onto brittle dope finishes to restore flexibility and soften cracking.
Blushing
A fabric finish defect presenting a porous and chalky white appearance, caused by moisture condensing on wet dope when surface temperature drops below the dew point.
Fisheyes
Small, circular finish defects caused by surface contaminants such as wax, silicone, oil, or water.
Dope Roping
A brush-mark defect in dope finishes that occurs when solvents evaporate faster than the dope can level out.
Universal Retarder
A slow-drying solvent additive mixed into dope to prevent blushing during application in high humidity.
EkoBond
A water-based contact adhesive used to attach fabric to airframes, cement seams, and bond finish tapes.