1/40
Comprehensive review flashcards covering Super High Frequency (SHF) communications, Commercial Broadband Satellite Program (CBSP), Navy Multiband Terminal (NMT) architecture, EBEM modems, fault management, and frequency band specifications.
What is the primary function of Super High Frequency (SHF) communications, and what mission area does it support?
It provides reliable telecommunications services essential to C4I missions (Command, Control, Communications, Computers, Combat Systems, and Intelligence).
What are the supported data rates and operating radio frequency range of Super High Frequency (SHF) communications?
It supports data rates from 64kbps to greater than 21Mbps and transmits/receives radio communications in the 3–30GHz range.
Which specific frequency bands within the SHF spectrum are utilized on the Wideband Global SATCOM (WGS) system, and which are commercial?
X-band and Ka-band are used on the WGS system; C-band and Ku-band are used for commercial, cellphone, or satellite communications.
What is a Very Small Aperture Terminal (VSAT), and what operational condition does it require?
A two-way ground station with a small antenna that requires a clear line of sight (LOS) to the satellite.
What are the three SHF SATCOM segments, and what is the primary function of the Earth segment?
The three segments are Space, Earth, and Control. The Earth segment transmits and receives signals between SATCOM terminals (assigned to shore facilities, mobile ground forces, and Navy ships) and satellites.
What resources are provided by the Space segment of SHF SATCOM?
Transponder bandwidth, timeslots, and antenna position / beam location.
What are the three terminal variants of the Commercial Broadband Satellite Program (CBSP)?
Small Deck Variant (SSV), Unit Level Variant (ULV), and Force Level Variant (FLV).
What are the platform assignments, operating band, and data rate of the CBSP Small Deck Variant (SSV) AN/USC-69(V)?
It operates in the Ku-band on small deck ships (PC and MCM ships) at data rates from 64kbps to 3.356Mbps.
What antenna configurations are available for the CBSP Unit Level Variant (ULV), and what ship classes host it?
Single-antenna and dual-antenna configurations, deployed on DDGs and CGs.
What are the two configurations of the CBSP Force Level Variant (FLV) AN/USC-69(V)2, and where is it installed?
Single-antenna with single-carrier configuration, and dual-antenna with dual-carrier configuration; installed on large decks including CVN, LHA, LHD, and LCC.
What are the structural designations of equipment groups in CBSP and NMT?
Below Deck Equipment (BDE), also designated as Communications Group (CG); and Above Deck Equipment (ADE), also designated as Antenna Group (AG).
What is the Global Broadcast Service (GBS), and what type of communication does it provide?
A shipboard receive suite that functions as a receive-only circuit providing one-way transmission of classified information.
What is the function of the Prime Power Interface (PPI) in the Navy Multiband Terminal (NMT)?
It converts 440V alternating current (VAC) to direct current (DC) voltages required for the NMT system (converting 3-phase 440V to 200V PT).
What are the six sequential power-on steps for the Navy Multiband Terminal (NMT)?
What menus are available from the drop-down menu on the NMT Top-level window?
File (import/export data, reset/shutdown), Terminal setup (terminal configuration), View Sat (satellite blockage), EHF Comms (EHF configuration settings), Maintenance, Windows, and Help.
What are the four unique user roles in the Navy Multiband Terminal (NMT) system, and what restriction exists between them?
System Administration (SA), Operator/Maintainer, Security Officer, and Navy Officer (note: Security Officer is not required to be a Navy Officer). Users may hold a maximum of 2 roles, but System Admin and Security Officer cannot be the same person.
What are the minimum staffing requirements for NMT System Administrators, Operators, and Security Officers?
Operator/Maintainer: minimum of 1 operator per watch assignment; System Administrator (SA): minimum of 2 SAs per NMT platform/command; Security Officer: 1 per NMT platform/shore site.
Which NMT user role is responsible for performing End of Mission Sanitization (EOMS)?
The Security Officer.
What form is required to document NMT SA passwords for emergency access, and how is it secured?
Standard Form 700 (SF-700), classified SECRET because NMT is a SECRET system high system, and stored in a security container for SECRET storage.
What do the acronyms EBEM and ESEM stand for, and what modem model names are associated with them?
EBEM stands for Enhanced Bandwidth Efficient Modem (MD-1366/U); ESEM stands for Ethernet Service Expansion Module (MD-1392/U when combined).
What capability does adding the ESEM to the MD-1366/U modem provide?
It adds bulk encryption for all over-the-air traffic and enables the transport of Ethernet Local Area Network (LAN) traffic.
What conversion does the Comtech SLM-5650B perform?
It converts digital data to and from the KIV-119 or Ethernet data from ADNS to the L-Band (950–2000MHz) Intermediate Frequency (IF) utilized by the terminal.
What is the function of the NMT Intermediate Frequency (IF) Patch Panel?
It allows the operator to manually patch carrier signals from the NMT to the correct EBEM satellite modem and manually patch the antenna handover signal from the antenna to the EBEM.
Which three physical connections must always be patched on the serial connection to the EBEM?
Downlink, uplink, and handover EBEM.
From which entity must authorization be obtained prior to transmitting on wideband?
Wideband Satellite Communications Operations Center (WSOC).
What are the maximum and minimum power ratings for the Ka Solid State Amplifier (SSA) specified in the Terminal Configuration File (TCF)?
Maximum power is 43.0dBm; minimum power is 21.5dBm.
What do the green, yellow, and red indicator colors represent on the NMT Fault tab?
Green indicates no failures are occurring; yellow indicates a minor fault; red indicates a major fault.
How do the 'ACK' and 'Clear' buttons differ on the NMT message panel?
ACK (acknowledge) silences the audible alarm and retains the message in the Action tab; Clear silences the audible alarm and clears the message without adding it to the Action tab.
What is the purpose of the NONOPS test on the NMT antenna?
It is a non-operational test that verifies the Antenna Pointing Unit (APU) and isolates faults if the APU is not functioning properly.
What are the specific purposes of the Slow, Fast, and Reduced Antenna movement tests?
Slow Antenna movement test is used for new installations/ITSE; Fast Antenna movement test serves as a sanity check of antenna movement; Reduced Antenna movement test checks the motors/pedestal for reduced movement.
What elevation parameter must be verified when conducting an Antenna Motor Drive (power amp) test?
Verify that elevation is less than 10∘.
What are the four possible causes of an X-band or Ka-band communications failure?
Equipment fault, EMCON enabled, low satellite elevation, and poor weather conditions.
Where and within what timeframe must the End of Mission (EOM) / After Mission Report be submitted?
Submitted via the Joint Integrated SATCOM Tool (JIST) following mission completion or within 10 days.
How is Plain Old Telephone System (POTS) traffic transported across the Automated Digital Network System (ADNS)?
It is converted from analog to digital and carried across ADNS / Protected core via Internet Protocol (IP).
How do ASYNC, ISOC, and SYNC digital data transmissions differ regarding clock synchronization and error checking?
ASYNC is transmitted without timing sync (low-speed) and includes a parity bit for error indication; ISOC is transmitted without timing sync and without start, stop, or parity bits; SYNC uses timing sync without start, stop, or parity bits, has no error checking, and is used for high-speed transmissions like CBSP.
What timing source provides a constant, known decay rate to minimize communication disruptions and timing errors?
An atomic clock utilizing cesium material.
What does Eb/N0 measure, and what do values of <4, ≥7, 7–12, and >12 represent?
It measures energy per bit over noise power density (a signal-to-noise ratio SNR measuring EBEM reception quality). <4 causes degradation; ≥7 indicates a strong receive signal; 7–12 is optimal; and >12 will damage the satellite.
What are the two primary sections of the Local Control Terminal (LCT) Human Computer Interface (HCI)?
The System network tree and the MD-1366/U main configuration & monitor window.
What are the characteristics of the Shared Modem Authentication Token (SMAT) Key and the RNG seed key?
The SMAT key is usually 40 characters long with a 5-digit Error Detection Code (EDC); the RNG seed key is an AES-256 encryption key required to operate the modem as an Ethernet connection.
What are the definitions of Condition, Hard, and Configuration faults in the modem system?
Condition fault: loss of acquisition / antenna LOS blockage; Hard fault: faulted High Power Amplifier (HPA) or loss of system component; Configuration fault: incorrect equipment settings, component settings, or KEYMAT.
What are the exact frequency boundaries for S-band, C-band, X-band, Ku-band, K-band, and Ka-band?
S-band: 3–4GHz; C-band: 4–8GHz; X-band: 8–12GHz; Ku-band: 12–18GHz; K-band: 18–27GHz; Ka-band: 27–30GHz.