Automotive Computers, Electronics, Sensors, and Actuators

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/56

flashcard set

Earn XP

Description and Tags

Comprehensive practice flashcards covering automotive computer systems, digital logic, semiconductor components, sensor operations, actuator circuits, diagnostic waveforms, and regulatory standards.

57 Terms

1
New cards

In what year did the widespread mass adoption of electronic engine control computers occur across automobile manufacturers?

19811981.

2
New cards

Which early mass-produced electronic fuel injection system was introduced in 19681968 on Volkswagen vehicles?

Bosch D-Jetronics.

3
New cards

What electronic systems were introduced on vehicles in 19751975 and 19761976 respectively?

In 19751975, Cadillac Fuel Injection; in 19761976, Oldsmobile MISAR (Microprocessed Sensing Automatic Regulation) for electronic spark timing control.

4
New cards

What are the four primary functions executed by an automotive Central Processing Unit (CPU)?

Input, Process, Storage, and Output.

5
New cards

How are a bit, a nibble, and a byte defined in automotive computer terminology?

A bit is a single binary digit (00 or 11), a nibble consists of 4 bits4\,\text{bits}, and a byte consists of 8 bits8\,\text{bits}.

6
New cards

In computer memory terminology, how many bytes are represented by 1 K1\,\text{K} of memory?

1024 bytes1024\,\text{bytes} (compared to 10001000 in standard decimal units).

7
New cards
<p>What logic state is produced by the digital circuit shown below when inputs A and B are varied?</p>

What logic state is produced by the digital circuit shown below when inputs A and B are varied?

An AND gate produces an output of 11 only when both inputs A and B are 11; otherwise, the output is 00.

8
New cards
<p>What output is produced by the digital logic gate shown below based on its truth table?</p>

What output is produced by the digital logic gate shown below based on its truth table?

An OR gate produces an output of 11 if input A, input B, or both are 11; it outputs 00 only when both inputs are 00.

9
New cards
<p>What is the function and truth table of the logic inverter gate shown below?</p>

What is the function and truth table of the logic inverter gate shown below?

A NOT gate inverts its input: an input of 00 yields an output of 11, and an input of 11 yields an output of 00.

10
New cards

What is the primary function of an Analog-to-Digital Converter (ADC) in an engine management computer?

It converts continuous analog voltage signals from sensors into binary digital numbers that the microprocessor can read and process.

11
New cards

What type of data is permanently stored in automotive ROM (Read Only Memory)?

Unchangeable operational instructions, operating algorithms, and mathematical formulas that persist even when power is disconnected.

12
New cards

What information is held in an automotive PROM / EEPROM, and how can it be serviced?

Vehicle-specific calibration lookup tables (fuel delivery, ignition timing, and sensor parameters), which can be reprogrammed or updated by "flashing" the computer.

13
New cards

What is the operational difference between volatile RAM (KAM) and nonvolatile RAM?

Volatile RAM (Keep Alive Memory) requires continuous battery power to retain adaptive learn data and DTCs, whereas nonvolatile RAM retains data (such as odometer mileage and door key codes) without power.

14
New cards

How does doping silicon with phosphorus produce an N-type semiconductor?

Phosphorus has 55 valence electrons; when combined with silicon (44 valence electrons), an extra free electron is introduced, creating negative-charge carriers.

15
New cards

How does doping silicon with boron produce a P-type semiconductor?

Boron has 33 valence electrons; when combined with silicon (44 valence electrons), an electron deficiency or "hole" is created, forming positive-charge carriers.

16
New cards
<p>How do NPN and PNP bipolar junction transistors differ in schematic symbol representation and current control?</p>

How do NPN and PNP bipolar junction transistors differ in schematic symbol representation and current control?

On an NPN transistor, the emitter arrow points outward (Not Pointing iN); on a PNP transistor, the emitter arrow points inward (Pointing iN). Current must flow to the base to enable collector-to-emitter flow.

17
New cards

What is the difference between a low-side driver and a high-side driver in a PCM actuator circuit?

A low-side driver is placed after the load to complete the ground path (a circuit short to ground keeps the actuator energized without overloading the driver); a high-side driver supplies power before the load (a short to ground can destroy the driver).

18
New cards

What are the five primary categories used to classify automotive sensors?

  1. Variable resistors (thermistors, potentiometers, piezoresistive, heated resistive), 2. Variable DC frequency sensors, 3. AC voltage generators, 4. DC voltage generators, and 5. Switches.
19
New cards

Why does a 2-wire thermistor sensor circuit require a fixed resistor inside the PCM?

To form a series voltage divider circuit; without the fixed resistor, the single variable resistor would drop the entire supply voltage (5 V5\,\text{V}) regardless of temperature changes.

20
New cards

In automotive sensor wiring harnesses, which lines can be shared and which must remain discrete?

The 5 V5\,\text{V} reference voltage and ground circuits can be spliced and shared across sensors, but the signal wire must always remain discrete to carry unique data.

21
New cards

What is the operational difference between a pull-up circuit switch and a pull-down circuit switch?

A pull-up circuit transitions from low to high voltage when the switch actuates (switch-to-power); a pull-down circuit transitions from high to low voltage when actuated (switch-to-ground).

22
New cards

How does a Hall-effect oil level switch detect low engine oil?

A float with an embedded magnet moves downward as oil level drops; the magnetic field acts on the Hall-effect chip, allowing voltage to flow and signaling the PCM.

23
New cards

According to the ASE composite ignition switch table, what voltage is present on each dedicated pin when the key is moved to its specific active position?

The active position grounds its respective pin to 0.0 V0.0\,\text{V} while the others read battery voltage (B+\text{B}+): OFF grounds Pin a, ACC grounds Pin b, RUN grounds Pin c, and START grounds Pin d.

24
New cards

How does an H-bridge circuit control the throttle actuator motor in an Electronic Throttle Control (ETC) system?

It uses four computer-controlled transistors to reverse motor current direction; one motor terminal receives a pulse-width modulated (PWM) signal while the other receives a constant 12 V12\,\text{V} or ground.

25
New cards

What are the default limp-in parameters when an Electronic Throttle Control (ETC) system experiences a dual-sensor or correlation failure?

The throttle plate returns to a spring-loaded 15%15\% opening, the scan tool TAC value indicates 15%15\%, and the engine fast idles at 1400 to 1500 rpm1400\text{ to }1500\,\text{rpm} under no load.

26
New cards

What control action does the ECM take if a single APP sensor or a single TP sensor experiences a circuit failure?

The ECM illuminates the Malfunction Indicator Lamp (MIL) and limits maximum throttle opening to 35%35\%.

27
New cards

What are the output voltage specifications for Accelerator Pedal Position sensors APP 1 and APP 2?

APP 1 outputs 0.5 V0.5\,\text{V} (released) to 3.5 V3.5\,\text{V} (fully applied); APP 2 outputs 1.5 V1.5\,\text{V} (released) to 4.5 V4.5\,\text{V} (fully applied), maintaining a continuous 1.0 V1.0\,\text{V} offset above APP 1.

28
New cards
<p>What relationship exists between the voltage signals of TP 1 and TP 2 in the dual throttle position sensor graph shown below?</p>

What relationship exists between the voltage signals of TP 1 and TP 2 in the dual throttle position sensor graph shown below?

The sensors produce opposite slopes: TP 1 decreases from 4.5 V4.5\,\text{V} to 0.5 V0.5\,\text{V} as the throttle opens, while TP 2 increases from 0.5 V0.5\,\text{V} to 4.5 V4.5\,\text{V}, always summing to 5.0 V5.0\,\text{V}.

29
New cards

What is the maximum operating current specification for the throttle actuator control (TAC) motor?

6 amps6\,\text{amps}.

30
New cards

What is the operational difference between a stepper motor and a DC servo motor actuator?

A stepper motor indexes in precise incremental steps (e.g., 90∘90^\circ increments) by sequencing current through multiple field coils; a servo motor rotates rapidly and continuously in either direction and uses a position potentiometer for feedback.

31
New cards

What are the enabling conditions and winding resistance for the EVAP canister purge solenoid?

Enabled when engine coolant temperature reaches 150∘F (66∘C)150^\circ\text{F}\,(66^\circ\text{C}) with duty cycle varied by engine speed and load; winding resistance is 36±4 Ω36 \pm 4\,\Omega.

32
New cards

Under what operating conditions is the Exhaust Gas Recirculation (EGR) valve solenoid enabled, and what is its resistance specification?

Enabled when ECT reaches 150∘F (66∘C)150^\circ\text{F}\,(66^\circ\text{C}) and the throttle is neither closed nor wide open; winding resistance is 12±2 Ω12 \pm 2\,\Omega.

33
New cards

At what engine coolant temperatures and A/C high-side pressures does the Fan Control (FC) relay energize and turn off?

Energizes when ECT reaches 220∘F (104∘C)220^\circ\text{F}\,(104^\circ\text{C}) or A/C pressure reaches 300 psi (2068 kPa)300\,\text{psi}\,(2068\,\text{kPa}); turns off when ECT drops to 195∘F (90∘C)195^\circ\text{F}\,(90^\circ\text{C}) or A/C pressure drops to 250 psi (1724 kPa)250\,\text{psi}\,(1724\,\text{kPa}).

34
New cards

What are the resistance specifications for the primary and secondary windings of the Coil-on-Plug (COP) ignition coils?

Primary resistance is 1±0.5 Ω1 \pm 0.5\,\Omega; secondary resistance is 10 kΩ±2 kΩ10\,\text{k}\Omega \pm 2\,\text{k}\Omega.

35
New cards

How does the ECM hold a desired camshaft advance angle in a Variable Valve Timing (VVT) system?

Once the target camshaft advance is reached, the ECM commands a steady 50%50\% duty cycle to the camshaft position actuator control solenoid to maintain oil pressure balance.

36
New cards

What are the switching threshold and valve lift increase in the Variable Valve Lift (VVL) control system?

Below 3000 rpm3000\,\text{rpm}, command is 0%0\% (0.50 V0.50\,\text{V}); above 3000 rpm3000\,\text{rpm}, command is 100%100\% (4.50 V4.50\,\text{V}), which adjusts the rocker arm fulcrum to add 4 mm4\,\text{mm} of valve lift.

37
New cards

How do Normally Low (NL) and Normally High (NH) variable force solenoids differ in hydraulic clutch control?

When de-energized (OFF), an NL solenoid exhausts fluid pressure (clutch released); when de-energized (OFF), an NH solenoid supplies high fluid pressure (clutch applied).

38
New cards

What duty cycle commands correspond to maximum and minimum transmission line pressure on the EPC solenoid?

A scan tool duty cycle of 10%10\% commands maximum line pressure, while 90%90\% duty cycle commands minimum line pressure.

39
New cards

What is the key electrical difference between a magnetic reluctance sensor and a Hall-effect sensor?

A magnetic reluctance sensor is a 2-wire analog generator producing an AC voltage whose amplitude and frequency increase with speed; a Hall-effect sensor is a 3-wire powered device outputting a digital DC square wave.

40
New cards

Why can a Crankshaft Position (CKP) sensor alone not determine engine stroke for sequential fuel injection and coil-on-plug ignition?

The crankshaft rotates twice per four-stroke cycle, making compression and exhaust strokes appear identical at the reluctor; the Camshaft Position (CMP) sensor rotates once per cycle to identify the cylinder stroke.

41
New cards

On the 35-pulse CKP reluctor wheel described in the composite manual, where is the missing tooth located?

At 60∘60^\circ before top dead center (BTDC\text{BTDC}) of cylinder number 11.

42
New cards

What frequency range of engine block vibration does a piezoelectric knock sensor detect, and what is its normal circuit bias voltage?

It detects vibrations between 6 kHz and 8 kHz6\,\text{kHz}\text{ and }8\,\text{kHz}, generating an AC voltage spike; the sensor circuit normally measures 2.5 V DC2.5\,\text{V DC} when connected.

43
New cards

What is the formula used by a Speed Density fuel injection system to calculate engine airflow?

RPM×EGR×VE×MAPIAT\frac{\text{RPM} \times \text{EGR} \times \text{VE} \times \text{MAP}}{\text{IAT}}.

44
New cards

How does a heated-wire mass airflow (HWMAF) sensor measure intake air mass?

The sensing wire is electrically maintained at 100∘C100^\circ\text{C} above ambient air temperature; incoming intake air cools the wire, and the current needed to restore that temperature is measured as airflow.

45
New cards

What are typical scan tool Absolute Load values at wide open throttle (WOT) versus normal idle?

Normal absolute load at WOT is approximately 95%95\%, while typical idle values are approximately 15%15\%.

46
New cards
<p>What absolute pressure and voltage values correspond to atmospheric pressure and normal idle on the chart shown below?</p>

What absolute pressure and voltage values correspond to atmospheric pressure and normal idle on the chart shown below?

Atmospheric pressure is 14.7 PSIA (0 PSIG)14.7\,\text{PSIA}\,(0\,\text{PSIG}) with a MAP voltage of 4.8 V4.8\,\text{V}; normal engine idle is 4.9 PSIA (20 in. Hg vacuum)4.9\,\text{PSIA}\,(20\,\text{in. Hg vacuum}) with a MAP voltage of 1.10 V1.10\,\text{V}.

47
New cards

What are the output voltage parameters of the Fuel Tank (EVAP) Pressure Sensor across its working pressure range?

0.5 V0.5\,\text{V} at −0.500 psi (−14 in. H2O)-0.500\,\text{psi}\,(-14\,\text{in. }\text{H}_2\text{O}), 2.5 V2.5\,\text{V} at 0.000 psi0.000\,\text{psi} (fuel cap removed), and 4.5 V4.5\,\text{V} at +0.500 psi (+14 in. H2O)+0.500\,\text{psi}\,(+14\,\text{in. }\text{H}_2\text{O}).

48
New cards

What is the difference in resistance behavior between an NTC thermistor and a PTC thermistor?

An NTC (Negative Temperature Coefficient) thermistor decreases resistance as temperature increases; a PTC (Positive Temperature Coefficient) thermistor increases resistance as temperature increases.

49
New cards

Why do automotive PCMs incorporate a dual-range stepped pull-up circuit for Engine Coolant Temperature (ECT) sensors?

NTC thermistors experience very small resistance changes per degree at normal operating temperatures (190∘F to 210∘F190^\circ\text{F}\text{ to }210^\circ\text{F}); switching to a smaller internal resistor (909 Ω909\,\Omega) at 120∘F to 140∘F120^\circ\text{F}\text{ to }140^\circ\text{F} restores voltage sensitivity.

50
New cards
<p>What exhaust gas trends occur as air-fuel ratio moves from rich to lean according to the graph shown below?</p>

What exhaust gas trends occur as air-fuel ratio moves from rich to lean according to the graph shown below?

CO\text{CO} and HC\text{HC} drop sharply on the rich side and flatten out; CO2\text{CO}_2 reaches maximum concentration at stoichiometry (14.7:114.7:1); O2\text{O}_2 is near zero while rich and increases steadily as the mixture leans.

51
New cards

What four elements are required for a conventional zirconia oxygen sensor to generate a voltage signal?

Zirconium dioxide (ZrO2\text{ZrO}_2), platinum electrode plating, high temperature (minimum 600∘F600^\circ\text{F}, optimal 1450∘F1450^\circ\text{F}), and a difference in oxygen concentration between exhaust gas and ambient air (21% O221\%\,\text{O}_2).

52
New cards

What voltage levels correspond to rich, stoichiometric, and lean air-fuel conditions on a narrow-band oxygen sensor?

Rich corresponds to high voltage (0.6 V to 1.0 V0.6\,\text{V}\text{ to }1.0\,\text{V}); stoichiometric corresponds to 0.45 V0.45\,\text{V} (0.455 V0.455\,\text{V}); lean corresponds to low voltage (0.1 V to 0.3 V0.1\,\text{V}\text{ to }0.3\,\text{V}).

53
New cards
<p>What are the procedural steps and pass criteria for the DSO propane oxygen sensor test shown below?</p>

What are the procedural steps and pass criteria for the DSO propane oxygen sensor test shown below?

With engine at operating temp in closed loop, adding propane must drive sensor output above 800 mV800\,\text{mV}; shutting propane off must drop output below 200 mV200\,\text{mV}; re-adding propane must produce a rich transition in less than 100 ms100\,\text{ms}.

54
New cards

On an oxygen sensor scope waveform, what is the diagnostic difference between significant hash and amplified hash?

Significant hash occurs above the 0.6 V0.6\,\text{V} line and below the 0.3 V0.3\,\text{V} line and indicates cylinder combustion or misfire faults; amplified hash occurs between 0.3 V and 0.6 V0.3\,\text{V}\text{ and }0.6\,\text{V} and is typically ignored.

55
New cards

How does a planar-type Air/Fuel Ratio Sensor (AFRS) indicate mixture changes to the ECM via scan tool voltage and current?

Stoichiometric (14.7:114.7:1, Lambda 1.001.00) reads 2.5 V2.5\,\text{V} and 0 μA0\,\mu\text{A}; rich mixtures produce negative current down to −2000 μA-2000\,\mu\text{A} (1.3 V1.3\,\text{V} at 11:111:1); lean mixtures produce positive current up to +3000 μA+3000\,\mu\text{A} (4.3 V4.3\,\text{V} at 20:120:1).

56
New cards

What three vehicle design parameters exist in direct conflict within the automotive emissions control triangle?

Exhaust emissions control, good driveability, and good fuel economy.

57
New cards

What are the EPA Tier 2 emissions limits for all light vehicles at 50,000 miles50,000\,\text{miles}?

NMOG:0.075–0.125 g/mi\text{NMOG}: 0.075\text{--}0.125\,\text{g/mi}, CO:3.4 g/mi\text{CO}: 3.4\,\text{g/mi}, NOx:0.05–0.4 g/mi\text{NO}_x: 0.05\text{--}0.4\,\text{g/mi}, and HCHO:0.015 g/mi\text{HCHO}: 0.015\,\text{g/mi}.