Analog Electronic Circuits: Field Effect Transistors, Feedback Amplifiers, and Oscillators

Field Effect Transistors (FETs) are unipolar, voltage-controlled semiconductor devices in which output conduction is governed by an electric field rather than direct base current injection. The electric field is established across a conducting channel via an applied gate voltage (VGSV_{GS}), allowing modulation of the channel cross-section and carrier density without requiring direct electrical contact between the controlling gate and the controlled drain-source path. This operating principle gives FETs exceptionally high input impedance, low power consumption, and thermal stability.

1.1 Comprehensive Comparison Between BJTs and FETs
  • Operating Control Mechanism:

    • BJT: Current-controlled device (IC=f(IB)I_C = f(I_B)). Conduction across the base-emitter junction requires a continuous direct base current (IBI_B) to control the collector current (ICI_C).

    • FET: Voltage-controlled device (ID=f(VGS)I_D = f(V_{GS})). Conduction along the channel is regulated electrostatically by the input gate-to-source voltage (VGSV_{GS}) without requiring gate current conduction (IG≈0 AI_G \approx 0\,\text{A}).

  • Charge Carriers and Conduction Type:

    • BJT: Bipolar device. Conduction is mediated simultaneously by both majority and minority charge carriers (electrons and holes).

    • FET: Unipolar device. Current transport is strictly mediated by majority carriers only (electrons in n-channel devices, holes in p-channel devices).

  • Input Impedance:

    • BJT: Exhibits relatively low input impedance (Zi≈1 kΩZ_i \approx 1\,\text{k}\Omega to 10 kΩ10\,\text{k}\Omega) because the input base-emitter junction operates under forward-bias conditions.

    • FET: Exhibits extremely high input impedance (Zi≈109 ΩZ_i \approx 10^9\,\Omega for JFETs due to reverse-biased gate junctions, and Zi≈1012 ΩZ_i \approx 10^{12}\,\Omega to 1015 Ω10^{15}\,\Omega for MOSFETs due to the insulating silicon dioxide layer).

  • Thermal Stability and Temperature Coefficient:

    • BJT: Exhibits a negative temperature coefficient of resistance, making it prone to thermal runaway under elevated power dissipation.

    • FET: Exhibits a positive temperature coefficient of resistance; carrier mobility decreases as temperature increases, self-limiting the channel current and providing superior thermal stability.

  • Fabrication, Scale, and Energy Efficiency:

    • BJT: Requires larger physical silicon area and involves complex fabrication sequences when integrated into monolithic integrated circuits (ICs).

    • FET: Substantially smaller in physical dimensions, simple to fabricate in high density on silicon substrates, highly energy-efficient with minimal static power loss, and ideally suited for large-scale VLSI/ULSI integration.

  • Gain-Bandwidth and Frequency Handling:

    • BJT: Typically offers higher transconductance and higher gain-bandwidth product (fTf_T).

    • FET: Offers lower gain-bandwidth product but superior performance in low-noise amplification, high-input-impedance instrumentation, and high-frequency analog/digital switching.

1.2 JFET Device Physics, Operation, and Characteristics
  • Physical Construction and Terminals:

    • Source (SS): The terminal through which majority charge carriers enter the conducting channel.

    • Drain (DD): The terminal through which majority charge carriers exit the conducting channel. Drain current (IDI_D) is proportional to the number of majority carriers reaching this terminal.

    • Gate (GG): Heavily doped regions (p+p^+ for n-channel, n+n^+ for p-channel) formed on both sides of the channel that establish the controlling depletion boundaries.

    • Channel: The narrow physical pathway between the two gate diffusions through which carrier transport occurs.

  • Mechanism of Operation:

    • When gate-to-source reverse bias (VGSV_{GS}) is applied, the depletion regions around the p-n junctions widen, penetrating primarily into the lightly doped channel.

    • As ∣VGS∣|V_{GS}| increases, the conductive channel narrows, increasing channel resistance and restricting carrier flow between source and drain.

  • Shockley's Equation:

    • In the saturation (pinch-off) region, the relationship between input gate voltage and output drain current is quadratic and governed by Shockley's equation:     ID=IDSS(1−VGSVP)2I_D = I_{DSS}\left(1 - \frac{V_{GS}}{V_P}\right)^2

    • Rearranging to calculate the required gate-to-source bias for a specified drain current:     VGS=VP(1−IDIDSS)V_{GS} = V_P\left(1 - \sqrt{\frac{I_D}{I_{DSS}}}\right)

    • Maximum Saturation Current (IDSSI_{DSS}): Occurs at VGS=0 VV_{GS} = 0\,\text{V}, representing the maximum drain current in normal depletion-mode operation.

    • Pinch-Off Voltage (VPV_P): The critical reverse-bias gate voltage at which the two depletion boundaries touch, fully blocking channel conduction (ID=0 mAI_D = 0\,\text{mA}). For n-channel JFETs, VP<0 VV_P < 0\,\text{V}; for p-channel JFETs, VP>0 VV_P > 0\,\text{V}.

  • Transfer Characteristics Shorthand Plotting Method:

    • Rapid plotting of the parabolic transfer curve (IDI_D versus VGSV_{GS}) utilizes four standard landmark points:

    1. At VGS=0 VV_{GS} = 0\,\text{V}, ID=IDSSI_D = I_{DSS}

    2. At VGS=0.3VPV_{GS} = 0.3V_P, ID=IDSS2I_D = \frac{I_{DSS}}{2}

    3. At VGS=0.5VPV_{GS} = 0.5V_P, ID=IDSS4I_D = \frac{I_{DSS}}{4}

    4. At VGS=VPV_{GS} = V_P, ID=0 mAI_D = 0\,\text{mA}

  • Operating Regions on Drain Characteristics:

    • Ohmic / Linear Region (VDS<VGS−VPV_{DS} < V_{GS} - V_P): The channel behaves as an active voltage-controlled resistor with linear current response.

    • Saturation / Active Region (VDS≥VGS−VPV_{DS} \ge V_{GS} - V_P): The channel is pinched off at the drain end. Drain current reaches a constant level independent of VDSV_{DS}, governed purely by VGSV_{GS}.

    • Breakdown Region: Excessively high VDSV_{DS} induces avalanche multiplication across the reverse-biased junction, resulting in an uncontrolled surge in IDI_D.

1.3 Depletion-Type MOSFET (DE-MOSFET)
  • Physical Construction:

    • Formed on a p-type silicon substrate (for an n-channel device) into which two heavily doped n-regions are diffused to create the source and drain terminals.

    • An n-channel is physically fabricated between source and drain, providing a pre-existing conduction path under zero external bias.

    • A dielectric insulating layer of silicon dioxide (SiO2\text{SiO}_2) is grown over the channel, physically separating the metallic gate electrode from the semiconductor channel.

    • Because of this complete insulation, the device is also classified as an Insulated Gate FET (IGFET) with input leakage currents in the picoampere range.

    • The substrate (SSSS) is either connected internally to the source terminal or brought out externally as a fourth lead.

  • Dual-Mode Operation (N-Channel):

    • Depletion Mode (VGS<0 VV_{GS} < 0\,\text{V}): A negative gate potential repels conduction electrons from the n-channel down into the p-substrate while attracting holes into the channel region. Carrier recombination depletes free electrons, reducing channel conductivity until pinch-off is achieved at VGS=VPV_{GS} = V_P, where ID=0 mAI_D = 0\,\text{mA}.

    • Enhancement Mode (VGS>0 VV_{GS} > 0\,\text{V}): A positive gate potential attracts additional free minority electrons from the p-substrate upward toward the channel surface. This enhances channel carrier density and increases drain current above IDSSI_{DSS}.

    • Zero Gate Bias (VGS=0 V,VDS>0 VV_{GS} = 0\,\text{V}, V_{DS} > 0\,\text{V}): Majority electrons flow through the pre-existing channel, producing a saturation drain current equal to IDSSI_{DSS}.

  • Mathematical Formulation:

    • Shockley's equation applies universally across both depletion and enhancement regions:     ID=IDSS(1−VGSVP)2I_D = I_{DSS}\left(1 - \frac{V_{GS}}{V_P}\right)^2

    • In enhancement mode, positive values of VGSV_{GS} are directly substituted, yielding ID>IDSSI_D > I_{DSS}.

  • P-Channel Depletion MOSFET:

    • Built with an n-type substrate and a pre-existing p-channel.

    • Voltage polarities and current directions are reversed: VDSV_{DS} is negative, depletion mode occurs when VGS>0 VV_{GS} > 0\,\text{V}, and enhancement mode occurs when VGS<0 VV_{GS} < 0\,\text{V}.

1.4 Enhancement-Type MOSFET (E-MOSFET)
  • Physical Construction:

    • Fabricated on a p-type substrate with isolated, heavily doped n-wells for the drain and source.

    • Unlike the DE-MOSFET, no physical channel is fabricated between drain and source; the regions are separated by the intervening p-type substrate.

    • A thin SiO2\text{SiO}_2 dielectric layer insulates the metallic/polysilicon gate terminal from the substrate region.

  • Operating Principle and Channel Inversion:

    • Zero Gate Bias (VGS=0 V,VDS>0 VV_{GS}=0\,\text{V},V_{DS}>0\,\text{V} ): Two back-to-back p-n junctions exist between drain and source. Current conduction cannot occur, resulting in ID=0 mAI_D = 0\,\text{mA}.

    • Sub-Threshold Bias (0<VGS<VT0 < V_{GS} < V_T): Positive gate potential repels majority holes from the oxide boundary, creating an immobile depletion layer, but carrier density is insufficient for conduction (ID=0 mAI_D = 0\,\text{mA}).

    • Inversion Layer Formation (VGS≥VTV_{GS} \ge V_T): When the gate voltage reaches the threshold voltage (VTV_T or VGS(th)V_{GS(\text{th})}), the positive electric field draws sufficient minority electrons from the substrate to the surface, creating an n-type inversion layer. This induced channel bridges the source and drain.

    • Pinch-Off and Saturation (VDS≥VGS−VTV_{DS} \ge V_{GS} - V_T):

    • As drain voltage increases, the drain-to-gate potential difference (VDG=VDS−VGSV_{DG} = V_{DS} - V_{GS}) decreases the field across the dielectric near the drain end.

    • The induced channel narrows near the drain until it pinches off at the saturation voltage:       VDS(sat)=VGS−VTV_{DS(\text{sat})} = V_{GS} - V_T

    • Beyond this boundary, the drain current saturates and remains constant regardless of further increases in VDSV_{DS}.

  • Current-Voltage Governing Equations:

    • For VGS<VTV_{GS} < V_T: Cutoff condition occurs with ID=0 mAI_D = 0\,\text{mA}.

    • For VGS≥VTV_{GS} \ge V_T in the saturation region (VDS≥VGS−VTV_{DS} \ge V_{GS} - V_T):     ID=k(VGS−VT)2I_D = k(V_{GS} - V_T)^2

    • Conduction Parameter (kk): Determined experimentally from data sheet specifications:     k=ID(on)(VGS(on)−VT)2k = \frac{I_{D(\text{on})}}{(V_{GS(\text{on})} - V_T)^2}     where kk is expressed in A/V2\text{A/V}^2 or mA/V2\text{mA/V}^2.

  • P-Channel Enhancement MOSFET:

    • Fabricated on an n-type substrate with p-doped source and drain regions.

    • Requires a negative gate-to-source voltage below a negative threshold voltage (VGS≤VTV_{GS} \le V_T, where VT<0 VV_T < 0\,\text{V}) to attract holes and induce a p-type inversion layer.

1.5 Complementary MOSFET (CMOS) Inverter
  • Circuit Architecture:

    • Configured by integrating a p-channel E-MOSFET (PMOS) and an n-channel E-MOSFET (NMOS) on a single silicon substrate.

    • The PMOS source is connected to the positive DC supply rail (VSS=5 VV_{SS} = 5\,\text{V}), while the NMOS source is tied directly to circuit ground (0 V0\,\text{V}).

    • The gate electrodes of both transistors are tied together to form the input terminal (ViV_i).

    • The drain terminals of both transistors are tied together to form the output terminal (VoV_o).

  • Switching Mechanics and Logic Inversion:

    • High Input (Vi=5 VV_i = 5\,\text{V}, Logic 1):

    • NMOS gate bias is VGS1=5 V>VTV_{GS1} = 5\,\text{V} > V_T, turning the NMOS ON into a low-resistance state.

    • PMOS gate bias is VGS2=Vi−VSS=5 V−5 V=0 VV_{GS2} = V_i - V_{SS} = 5\,\text{V} - 5\,\text{V} = 0\,\text{V}, which is greater than the negative threshold VT(PMOS)V_{T(\text{PMOS})}, turning the PMOS OFF into a high-resistance state.

    • The output node is connected to ground through the low-resistance NMOS channel, pulling the output down: Vo=0 VV_o = 0\,\text{V} (Logic 0).

    • Low Input (Vi=0 VV_i = 0\,\text{V}, Logic 0):

    • NMOS gate bias is VGS1=0 V<VTV_{GS1} = 0\,\text{V} < V_T, turning the NMOS OFF into a high-resistance state.

    • PMOS gate bias is VGS2=0 V−5 V=−5 V<VT(PMOS)V_{GS2} = 0\,\text{V} - 5\,\text{V} = -5\,\text{V} < V_{T(\text{PMOS})}, turning


Comprehensive solutions and analytical derivations for the Analog Electronic Circuits (24BEC302) Question Bank, systematically arranged according to syllabus modules and marks allotted.







1. Module 1: Field Effect Transistors
Unit 1: Device Physics, Comparisons, and Frequency Analysis (6 Marks Each)
  1. Compare BJT and JFET (6 Marks)

    • Operating Control Mechanism: BJT is a current-controlled device where the collector output current is controlled by the base input current (IC=f(IB)I_C = f(I_B)). JFET is an electrostatic, voltage-controlled device where drain current is controlled by the reverse gate-to-source voltage (ID=f(VGS)I_D = f(V_{GS})).

    • Charge Carrier Transport: BJT is a bipolar device whose conduction involves both majority and minority charge carriers (electrons and holes). JFET is a unipolar device whose conduction is mediated strictly by majority carriers (electrons in n-channel, holes in p-channel).

    • Input Impedance: BJT has relatively low input impedance (Zi≈1 kΩZ_i \approx 1\,\text{k}\Omega to 10 kΩ10\,\text{k}\Omega) because its controlling base-emitter junction is forward-biased. JFET exhibits exceptionally high input impedance (Zi≈109 ΩZ_i \approx 10^9\,\Omega) due to its reverse-biased gate-channel p-n junction.

    • Thermal Stability: BJT exhibits a negative temperature coefficient of resistance, making it prone to thermal runaway under power dissipation. JFET has a positive temperature coefficient of resistance; carrier mobility drops as temperature increases, providing inherent self-limiting thermal stability.

    • Noise Performance and IC Fabrication: JFET produces significantly lower noise than BJT because it lacks current-crossing p-n junctions during normal channel transport. Furthermore, JFETs occupy much smaller silicon real estate and are simpler to fabricate in high-density integrated circuits.

    • Gain-Bandwidth Product: BJTs generally offer higher transconductance and superior gain-bandwidth product (fTf_T), whereas JFETs feature lower transconductance and lower gain-bandwidth product.

  2. Compare JFET and MOSFET (6 Marks)

    • Gate Physical Construction: JFET gate forms a direct metallurgical p-n junction with the channel. MOSFET gate is physically and electrostatically isolated from the channel by a thin dielectric layer of silicon dioxide (SiO2\text{SiO}_2).

    • Input Impedance Level: While JFET has high input impedance (Zi≈109 ΩZ_i \approx 10^9\,\Omega), MOSFET exhibits ultra-high input impedance (Zi≈1012 ΩZ_i \approx 10^{12}\,\Omega to 1015 Ω10^{15}\,\Omega) because the insulating SiO2\text{SiO}_2 layer prevents conduction current.

    • Gate Leakage Current: JFET exhibits a finite reverse leakage gate current (IGI_G) in the nanoampere (nA\text{nA}) range. MOSFET exhibits negligible leakage gate current in the picoampere (pA\text{pA}) range.

    • Operational Modes: JFET can only operate in depletion mode (widening the depletion boundary). MOSFETs operate in both depletion mode and enhancement mode (DE-MOSFET) or strictly in enhancement mode (E-MOSFET).

    • Electrostatic Discharge (ESD) Sensitivity: JFETs are rugged and robust against moderate transient electrostatic charges. MOSFETs are delicate and susceptible to permanent dielectric breakdown from static gate charge accumulation.

    • VLSI Integration: MOSFETs require smaller physical dimensions, exhibit near-zero static power dissipation (notably in CMOS), and are the primary foundation of high-density digital processors and memories.

  3. Compare Enhancement and Depletion Type MOSFET (6 Marks)

    • Channel Presence Under Zero Bias: Depletion-type MOSFET (DE-MOSFET) has a pre-existing, physically diffused semiconductor channel between source and drain. Enhancement-type MOSFET (E-MOSFET) has no pre-existing channel; the channel is induced electrostatically.

    • Conduction at Zero Gate Bias (VGS=0 VV_{GS} = 0\,\text{V}): DE-MOSFET conducts maximum saturation current (ID=IDSSI_D = I_{DSS}) at VGS=0 VV_{GS} = 0\,\text{V}. E-MOSFET is completely non-conducting (ID=0 mAI_D = 0\,\text{mA}) because back-to-back p-n junctions block carrier transport.

    • Operating Modes: DE-MOSFET supports dual-mode operation: depletion mode for reverse polarities (VGS<0 VV_{GS} < 0\,\text{V} for n-channel) and enhancement mode for forward polarities (VGS>0 VV_{GS} > 0\,\text{V}). E-MOSFET operates solely in enhancement mode when VGS≥VTV_{GS} \ge V_T.

    • Threshold versus Pinch-Off Voltage: DE-MOSFET is characterized by pinch-off voltage (VPV_P) where channel conduction ceases. E-MOSFET is characterized by threshold voltage (VTV_T) below which no inversion channel forms.

    • Governing Mathematical Equation: DE-MOSFET satisfies Shockley's equation:
      ID=IDSS(1−VGSVP)2I_D = I_{DSS}\left(1 - \frac{V_{GS}}{V_P}\right)^2
           E-MOSFET in saturation satisfies the square-law equation:
      ID=k(VGS−VT)2I_D = k(V_{GS} - V_T)^2

    • Primary Applications: DE-MOSFET is utilized in high-frequency RF amplifiers and linear current limiters. E-MOSFET is utilized as the primary switching transistor in VLSI digital logic (CMOS) and power electronic converters.

  4. Low-Frequency Response and Capacitor Influence in FET Amplifiers (6 Marks)

    • Mechanism of Low-Frequency Attenuation: At low frequencies, the capacitive reactances (XC=12πfCX_C = \frac{1}{2\pi f C}) of external DC-blocking coupling capacitors and bypass capacitors increase substantially, causing signal attenuation, phase distortion, and low-frequency roll-off.

    • Input Coupling Capacitor (CGC_G): Forms a high-pass RC filter with the signal source resistance RsigR_{\text{sig}} and the stage input resistance Ri=RGR_i = R_G. The lower 3 dB3\,\text{dB} cutoff frequency is:
      fLG=12π(Rsig+Ri)CGf_{L_G} = \frac{1}{2\pi(R_{\text{sig}} + R_i)C_G}
           Because RGR_G is very large (in megaohms), fLGf_{L_G} is located at a very low frequency.

    • Output Coupling Capacitor (CCC_C): Forms a high-pass network with the amplifier's AC output resistance Ro=rd∥RDR_o = r_d \parallel R_D and the load resistor RLR_L. The resulting cutoff frequency is:
      fLC=12π[(rd∥RD)+RL]CCf_{L_C} = \frac{1}{2\pi\left[(r_d \parallel R_D) + R_L\right]C_C}

    • Source Bypass Capacitor (CSC_S): Bypasses source resistor RSR_S to eliminate AC degeneration and maintain high stage gain. The cutoff frequency depends on the Thevenin equivalent resistance seen looking into the source terminal:
      fLS=12πReqCSf_{L_S} = \frac{1}{2\pi R_{\text{eq}} C_S}
           where:
      Req=RS∥[rd+(RD∥RL)1+gmrd]≈RS∥1gmfor rd≈∞ ΩR_{\text{eq}} = R_S \parallel \left[\frac{r_d + (R_D \parallel R_L)}{1 + g_m r_d}\right] \approx R_S \parallel \frac{1}{g_m} \quad \text{for } r_d \approx \infty\,\Omega

    • Dominant Low-Frequency Cutoff: The overall lower cutoff frequency fLf_L of the amplifier is governed by the highest of the three cutoff frequencies:
      fL≈max⁡(fLG,fLC,fLS)f_L \approx \max(f_{L_G}, f_{L_C}, f_{L_S})
           In practice, fLSf_{L_S} is almost always the dominant lower pole because ReqR_{\text{eq}} is very small, requiring a large capacitance CSC_S.

  5. Analysis of High-Frequency Response in FET Amplifiers (6 Marks)

    • High-Frequency Attenuation Factors: High-frequency roll-off is dictated by device internal parasitic interelectrode capacitances (Cgs,Cgd,CdsC_{gs}, C_{gd}, C_{ds}) and external wiring stray capacitances (CWi,CWoC_{W_i}, C_{W_o}).

    • Miller Effect Magnification: The bridging feedback capacitance CgdC_{gd} between the inverting input and output nodes experiences voltage feedback magnification, appearing at the input as Miller capacitance:
      CMi=(1−Av)CgdC_{M_i} = (1 - A_v)C_{gd}
           and at the output as:
      CMo=(1−1Av)Cgd≈Cgdwhen ∣Av∣≫1C_{M_o} = \left(1 - \frac{1}{A_v}\right)C_{gd} \approx C_{gd} \quad \text{when } |A_v| \gg 1

    • Total Input High-Frequency Capacitance (CiC_i):
      Ci=CWi+Cgs+CMi=CWi+Cgs+(1−Av)CgdC_i = C_{W_i} + C_{gs} + C_{M_i} = C_{W_i} + C_{gs} + (1 - A_v)C_{gd}

    • High-Frequency Input Cutoff (fHif_{H_i}): Determined by the input Thevenin resistance RThi=Rsig∥RGR_{\text{Th}_i} = R_{\text{sig}} \parallel R_G:
      fHi=12πRThiCif_{H_i} = \frac{1}{2\pi R_{\text{Th}_i} C_i}

    • High-Frequency Output Cutoff (fHof_{H_o}): Determined by total output capacitance Co=CWo+Cds+CMoC_o = C_{W_o} + C_{ds} + C_{M_o} and output Thevenin resistance RTho=RD∥RL∥rdR_{\text{Th}_o} = R_D \parallel R_L \parallel r_d:
      fHo=12πRThoCof_{H_o} = \frac{1}{2\pi R_{\text{Th}_o} C_o}

    • Upper Cutoff Determination: The overall upper 3 dB3\,\text{dB} frequency fHf_H is governed by the lower of the two poles:
      fH≈min⁡(fHi,fHo)f_H \approx \min(f_{H_i}, f_{H_o})
           Due to the large Miller capacitance CMiC_{M_i}, fHif_{H_i} typically establishes the upper bandwidth limit.

  6. Sketch Transfer Curve of JFET (IDSS=12 mAI_{DSS} = 12\,\text{mA}, VP=−6 VV_P = -6\,\text{V}) (6 Marks)

    • Governing Law: Shockley's equation describes the parabolic transfer characteristic in the saturation region:
      ID=IDSS(1−VGSVP)2I_D = I_{DSS}\left(1 - \frac{V_{GS}}{V_P}\right)^2

    • Four Landmark Plotting Points:

      • At VGS=0 VV_{GS} = 0\,\text{V}:
        ID=IDSS=12 mAI_D = I_{DSS} = 12\,\text{mA}

      • At VGS=0.3VP=0.3(−6 V)=−1.8 VV_{GS} = 0.3V_P = 0.3(-6\,\text{V}) = -1.8\,\text{V}:
        ID=IDSS2=12 mA2=6 mAI_D = \frac{I_{DSS}}{2} = \frac{12\,\text{mA}}{2} = 6\,\text{mA}

      • At VGS=0.5VP=0.5(−6 V)=−3.0 VV_{GS} = 0.5V_P = 0.5(-6\,\text{V}) = -3.0\,\text{V}:
        ID=IDSS4=12 mA4=3 mAI_D = \frac{I_{DSS}}{4} = \frac{12\,\text{mA}}{4} = 3\,\text{mA}

      • At VGS=VP=−6.0 VV_{GS} = V_P = -6.0\,\text{V}:
        ID=0 mAI_D = 0\,\text{mA}

    • Transfer Characteristic Coordinates:

      • Point 1: (VGS=0 V,ID=12 mA)(V_{GS} = 0\,\text{V}, I_D = 12\,\text{mA})

      • Point 2: (VGS=−1.8 V,ID=6 mA)(V_{GS} = -1.8\,\text{V}, I_D = 6\,\text{mA})

      • Point 3: (VGS=−3.0 V,ID=3 mA)(V_{GS} = -3.0\,\text{V}, I_D = 3\,\text{mA})

      • Point 4: (VGS=−6.0 V,ID=0 mA)(V_{GS} = -6.0\,\text{V}, I_D = 0\,\text{mA})

    • Curve Description: The transfer characteristic is sketched on the second quadrant (IDI_D on the positive vertical axis, VGSV_{GS} on the negative horizontal axis). It forms a smooth, upward-concave parabolic curve starting at the pinch-off point (−6 V,0 mA)(-6\,\text{V}, 0\,\text{mA}) and terminating at the y-intercept (0 V,12 mA)(0\,\text{V}, 12\,\text{mA}).

  7. Determine Pinch-Off Voltage of JFET (gm0=10 mSg_{m0} = 10\,\text{mS}, IDSS=12 mAI_{DSS} = 12\,\text{mA}) (6 Marks)

    • Fundamental Expression for Maximum Transconductance:
      gm0=2IDSS∣VP∣g_{m0} = \frac{2I_{DSS}}{|V_P|}

    • Rearranging for Magnitude of Pinch-Off Voltage (∣VP∣|V_P|):
      ∣VP∣=2IDSSgm0|V_P| = \frac{2I_{DSS}}{g_{m0}}

    • Step-by-Step Substitution:
      ∣VP∣=2×12×10−3 A10×10−3 S=24×10−310×10−3=2.4 V|V_P| = \frac{2 \times 12 \times 10^{-3}\,\text{A}}{10 \times 10^{-3}\,\text{S}} = \frac{24 \times 10^{-3}}{10 \times 10^{-3}} = 2.4\,\text{V}

    • Final Voltage Determination:

      • For an n-channel JFET: VP=−2.4 VV_P = -2.4\,\text{V}

      • For a p-channel JFET: VP=+2.4 VV_P = +2.4\,\text{V}


Unit 2: JFET Small-Signal Models and Amplifier Configurations (7 Marks Each)
  1. Derive Small-Signal Model of JFET with Proper Analysis (7 Marks)

    • Functional Dependency: The output drain current is a function of input gate-to-source voltage and output drain-to-source voltage: ID=f(VGS,VDS)I_D = f(V_{GS}, V_{DS}).

    • Total Differential Expansion:
      dID=∂ID∂VGS∣VDS=constdVGS+∂ID∂VDS∣VGS=constdVDSdI_D = \left.\frac{\partial I_D}{\partial V_{GS}}\right|_{V_{DS}=\text{const}} dV_{GS} + \left.\frac{\partial I_D}{\partial V_{DS}}\right|_{V_{GS}=\text{const}} dV_{DS}
           Replacing differentials with small-signal AC quantities (id,vgs,vdsi_d, v_{gs}, v_{ds}):
      id=gmvgs+1rdvdsi_d = g_m v_{gs} + \frac{1}{r_d} v_{ds}

    • Derivation of Transconductance (gmg_m): Differentiating Shockley's equation with respect to VGSV_{GS}:
      gm=ddVGS[IDSS(1−VGSVP)2]=2IDSS∣VP∣(1−VGSVP)g_m = \frac{d}{dV_{GS}}\left[I_{DSS}\left(1 - \frac{V_{GS}}{V_P}\right)^2\right] = \frac{2I_{DSS}}{|V_P|}\left(1 - \frac{V_{GS}}{V_P}\right)
           Setting maximum transconductance at VGS=0 VV_{GS} = 0\,\text{V} as gm0=2IDSS∣VP∣g_{m0} = \frac{2I_{DSS}}{|V_P|}:
      gm=gm0(1−VGSVP)=gm0IDIDSSg_m = g_{m0}\left(1 - \frac{V_{GS}}{V_P}\right) = g_{m0}\sqrt{\frac{I_D}{I_{DSS}}}

    • Derivation of Output Drain Resistance (rdr_d):
      rd=ΔVDSΔID∣VGS=const=1yos=1gosr_d = \left.\frac{\Delta V_{DS}}{\Delta I_D}\right|_{V_{GS}=\text{const}} = \frac{1}{y_{os}} = \frac{1}{g_{os}}

    • Small-Signal Equivalent Circuit Structure:

      • Input terminals (Gate to Source): Modeled as an ideal open circuit (Zi=∞ ΩZ_i = \infty\,\Omega) across which control voltage vgsv_{gs} appears.

      • Output terminals (Drain to Source): Modeled as a voltage-controlled current source gmvgsg_m v_{gs} directed downward from drain to source, shunted in parallel with output resistance rdr_d.

  2. Derive Small-Signal Model and Analysis of Fixed-Bias Configuration (7 Marks)

    • AC Equivalent Circuit Formulation: DC voltage sources (VGG,VDDV_{GG}, V_{DD}) are set to AC ground; coupling capacitors (C1,C2C_1, C_2) are replaced with short circuits. The input gate is tied to ground via RGR_G, and the output drain is connected to ground via RDR_D.

    • Input Impedance (ZiZ_i):
           Because the gate draws zero static current (Zin(device)=∞Z_{\text{in(device)}} = \infty), the input impedance seen by the AC generator is:
      Zi=RGZ_i = R_G

    • Output Impedance (ZoZ_o):
           Evaluated by setting signal voltage vi=0 Vv_i = 0\,\text{V}, which makes vgs=0 Vv_{gs} = 0\,\text{V}, reducing current source gmvgs=0 Ag_m v_{gs} = 0\,\text{A} to an open circuit. Looking into the drain terminal:
      Zo=rd∥RDZ_o = r_d \parallel R_D
           If rd≥10RDr_d \ge 10R_D, it simplifies to:
      Zo≈RDZ_o \approx R_D

    • Voltage Gain (AvA_v):
           Output AC voltage is produced by the current source flowing through the parallel combination of rdr_d and RDR_D:
      vo=−gmvgs(rd∥RD)v_o = -g_m v_{gs}(r_d \parallel R_D)
           Since the input voltage is applied directly across the gate-to-source terminal (vgs=viv_{gs} = v_i):
      Av=vovi=−gm(rd∥RD)A_v = \frac{v_o}{v_i} = -g_m(r_d \parallel R_D)
           If rd≥10RDr_d \ge 10R_D:
      Av≈−gmRDA_v \approx -g_m R_D

    • Phase Relationship: The negative sign confirms a 180∘180^\circ phase inversion between input and output AC signals.

  3. Derive Small-Signal Model and Analysis of Self-Bias Configuration (7 Marks)

    • AC Model Setup: The DC supply VDDV_{DD} is replaced by AC ground. The source bypass capacitor CSC_S acts as a short circuit across RSR_S, tying the FET source terminal directly to AC ground.

    • Input Impedance (ZiZ_i):
            Gate resistor RGR_G is connected between gate and ground. Since the JFET gate terminal represents an open circuit:
      Zi=RGZ_i = R_G

    • Output Impedance (ZoZ_o):
            Setting input vi=0 Vv_i = 0\,\text{V} gives vgs=0 Vv_{gs} = 0\,\text{V}, opening the current source gmvgs=0 Ag_m v_{gs} = 0\,\text{A}. The impedance looking back into the output is:
      Zo=rd∥RDZ_o = r_d \parallel R_D
      Zo≈RDif rd≥10RDZ_o \approx R_D \quad \text{if } r_d \ge 10R_D

    • Voltage Gain (AvA_v):
            Because the source is at AC ground, vgs=viv_{gs} = v_i. Output voltage across the drain load is:
      vo=−gmvgs(rd∥RD)=−gmvi(rd∥RD)v_o = -g_m v_{gs}(r_d \parallel R_D) = -g_m v_i(r_d \parallel R_D)
      Av=vovi=−gm(rd∥RD)A_v = \frac{v_o}{v_i} = -g_m(r_d \parallel R_D)
      Av≈−gmRDif rd≥10RDA_v \approx -g_m R_D \quad \text{if } r_d \ge 10R_D

    • Significance: Self-bias provides identical AC voltage gain and impedance performance to fixed bias while requiring only a single power supply (VDDV_{DD}).

  4. Derive Small-Signal Model of Voltage-Divider Bias Configuration (7 Marks)

    • AC Network Formation: Setting VDD=0 VV_{DD} = 0\,\text{V} places resistor R1R_1 in parallel with R2R_2 between gate and ground. Source resistor RSR_S is shorted to ground by bypass capacitor CSC_S.

    • Input Impedance (ZiZ_i):
            The parallel combination of the voltage divider resistors appears directly across the input terminals:
      Zi=R1∥R2Z_i = R_1 \parallel R_2

    • Output Impedance (ZoZ_o):
            Setting vi=0 Vv_i = 0\,\text{V} leaves vgs=0 Vv_{gs} = 0\,\text{V}, eliminating the dependent current generator:
      Zo=rd∥RDZ_o = r_d \parallel R_D
      Zo≈RDif rd≥10RDZ_o \approx R_D \quad \text{if } r_d \ge 10R_D

    • Voltage Gain (AvA_v):
            With source grounded, input signal appears fully across gate and source (vgs=viv_{gs} = v_i):
      vo=−gmvgs(rd∥RD)v_o = -g_m v_{gs}(r_d \parallel R_D)
      Av=vovi=−gm(rd∥RD)A_v = \frac{v_o}{v_i} = -g_m(r_d \parallel R_D)
      Av≈−gmRDif rd≥10RDA_v \approx -g_m R_D \quad \text{if } r_d \ge 10R_D

    • Comparative Trade-off: The voltage-divider bias yields stable DC Q-point biasing, but its AC input impedance (R1∥R2R_1 \parallel R_2) is lower than the megaohm range offered by fixed- or self-bias configurations.

  5. Numerical Problem on Fixed Bias Configuration (7 Marks)

    • Given Parameters: RD=2 kΩR_D = 2\,\text{k}\Omega, RG=1 MΩR_G = 1\,\text{M}\Omega, VDD=20 VV_{DD} = 20\,\text{V}, VGSQ=−2 VV_{GSQ} = -2\,\text{V}, IDQ=5.625 mAI_{DQ} = 5.625\,\text{mA}, IDSS=10 mAI_{DSS} = 10\,\text{mA}, VP=−8 VV_P = -8\,\text{V}, rd=25 kΩr_d = 25\,\text{k}\Omega.

    • Step 1: Calculate Maximum Transconductance (gm0g_{m0}):
      gm0=2IDSS∣VP∣=2(10 mA)8 V=2.5 mSg_{m0} = \frac{2I_{DSS}}{|V_P|} = \frac{2(10\,\text{mA})}{8\,\text{V}} = 2.5\,\text{mS}

    • Step 2: Calculate Transconductance at Q-Point (gmg_m):
      gm=gm0(1−VGSQVP)=2.5 mS(1−−2 V−8 V)=2.5(1−0.25)=1.875 mSg_m = g_{m0}\left(1 - \frac{V_{GSQ}}{V_P}\right) = 2.5\,\text{mS}\left(1 - \frac{-2\,\text{V}}{-8\,\text{V}}\right) = 2.5(1 - 0.25) = 1.875\,\text{mS}

    • Step 3: Determine Input Impedance (ZiZ_i):
      Zi=RG=1 MΩZ_i = R_G = 1\,\text{M}\Omega

    • Step 4: Determine Output Impedance (ZoZ_o):
      Zo=rd∥RD=25 kΩ∥2 kΩ=25×225+2=5027≈1.852 kΩZ_o = r_d \parallel R_D = 25\,\text{k}\Omega \parallel 2\,\text{k}\Omega = \frac{25 \times 2}{25 + 2} = \frac{50}{27} \approx 1.852\,\text{k}\Omega

    • Step 5: Determine Voltage Gain with rdr_d (AvA_v):
      Av=−gm(rd∥RD)=−(1.875 mS)(1.852 kΩ)=−3.47A_v = -g_m(r_d \parallel R_D) = -(1.875\,\text{mS})(1.852\,\text{k}\Omega) = -3.47

    • Step 6: Determine Voltage Gain Ignoring rdr_d:
      Av=−gmRD=−(1.875 mS)(2 kΩ)=−3.75A_v = -g_m R_D = -(1.875\,\text{mS})(2\,\text{k}\Omega) = -3.75

  6. Numerical Problem on Enhancement-Type MOSFET (7 Marks)

    • Given Parameters: VT=2 VV_T = 2\,\text{V}, ID(on)=10 mAI_{D(\text{on})} = 10\,\text{mA} at VGS(on)=8 VV_{GS(\text{on})} = 8\,\text{V}.

    • Step 1: Calculate Conduction Parameter (kk):
      k=ID(on)(VGS(on)−VT)2=10 mA(8 V−2 V)2=10 mA36 V2=0.278 mA/V2=0.278×10−3 A/V2k = \frac{I_{D(\text{on})}}{(V_{GS(\text{on})} - V_T)^2} = \frac{10\,\text{mA}}{(8\,\text{V} - 2\,\text{V})^2} = \frac{10\,\text{mA}}{36\,\text{V}^2} = 0.278\,\text{mA/V}^2 = 0.278 \times 10^{-3}\,\text{A/V}^2

    • Step 2: Calculate Drain Current at VGS=4 VV_{GS} = 4\,\text{V}:
      ID=k(VGS−VT)2=0.278 mA/V2×(4 V−2 V)2=0.278×4=1.11 mAI_D = k(V_{GS} - V_T)^2 = 0.278\,\text{mA/V}^2 \times (4\,\text{V} - 2\,\text{V})^2 = 0.278 \times 4 = 1.11\,\text{mA}

    • Step 3: Calculate Drain Current at VGS=2 VV_{GS} = 2\,\text{V}:
            Since VGS=VTV_{GS} = V_T, channel inversion is not yet established:
      ID=0 mAI_D = 0\,\text{mA}

    • Step 4: Calculate Drain Current at VGS=5 VV_{GS} = 5\,\text{V}:
      ID=k(VGS−VT)2=0.278 mA/V2×(5 V−2 V)2=0.278×9=2.50 mAI_D = k(V_{GS} - V_T)^2 = 0.278\,\text{mA/V}^2 \times (5\,\text{V} - 2\,\text{V})^2 = 0.278 \times 9 = 2.50\,\text{mA}

    • Plot Description of Transfer Characteristics:
            The curve is plotted on the first quadrant with ID (mA)I_D\,(\text{mA}) on the vertical axis and VGS (V)V_{GS}\,(\text{V}) on the horizontal axis. For all values VGS≤2 VV_{GS} \le 2\,\text{V}, ID=0 mAI_D = 0\,\text{mA}. Beyond VT=2 VV_T = 2\,\text{V}, the drain current increases quadratically, passing through points (4 V,1.11 mA)(4\,\text{V}, 1.11\,\text{mA}), (5 V,2.50 mA)(5\,\text{V}, 2.50\,\text{mA}), and (8 V,10.0 mA)(8\,\text{V}, 10.0\,\text{mA}).

  7. Numerical on Input/Output Impedance and Voltage Gain (7 Marks)

    • Given Parameters: IDSS=10 mAI_{DSS} = 10\,\text{mA}, VP=−6 VV_P = -6\,\text{V}, rd=40 kΩr_d = 40\,\text{k}\Omega, RD=1.8 kΩR_D = 1.8\,\text{k}\Omega, RG=1 MΩR_G = 1\,\text{M}\Omega, VDD=18 VV_{DD} = 18\,\text{V}, VGG=−1.5 VV_{GG} = -1.5\,\text{V}.

    • Step 1: Operating Gate Bias: For fixed bias, VGS=VGG=−1.5 VV_{GS} = V_{GG} = -1.5\,\text{V}.

    • Step 2: Calculate Maximum Transconductance (gm0g_{m0}):
      gm0=2IDSS∣VP∣=2(10 mA)6 V=3.333 mSg_{m0} = \frac{2I_{DSS}}{|V_P|} = \frac{2(10\,\text{mA})}{6\,\text{V}} = 3.333\,\text{mS}

    • Step 3: Calculate Transconductance (gmg_m):
      gm=gm0(1−VGSVP)=3.333 mS(1−−1.5 V−6 V)=3.333(1−0.25)=2.50 mSg_m = g_{m0}\left(1 - \frac{V_{GS}}{V_P}\right) = 3.333\,\text{mS}\left(1 - \frac{-1.5\,\text{V}}{-6\,\text{V}}\right) = 3.333(1 - 0.25) = 2.50\,\text{mS}

    • Step 4: Determine Input Impedance (ZiZ_i):
      Zi=RG=1 MΩZ_i = R_G = 1\,\text{M}\Omega

    • Step 5: Determine Output Impedance (ZoZ_o):
      Zo=rd∥RD=40 kΩ∥1.8 kΩ=40×1.840+1.8=7241.8≈1.722 kΩZ_o = r_d \parallel R_D = 40\,\text{k}\Omega \parallel 1.8\,\text{k}\Omega = \frac{40 \times 1.8}{40 + 1.8} = \frac{72}{41.8} \approx 1.722\,\text{k}\Omega

    • Step 6: Determine Voltage Gain (AvA_v):
      Av=−gm(rd∥RD)=−(2.50 mS)(1.722 kΩ)=−4.31A_v = -g_m(r_d \parallel R_D) = -(2.50\,\text{mS})(1.722\,\text{k}\Omega) = -4.31


Unit 3: Construction, MOSFET Physics, CMOS, and Miller Capacitance (7 Marks Each)
  1. Construction, Working Principle, and Characteristics of N-Channel JFET (7 Marks)

    • Physical Construction: Fabricated using a lightly doped n-type silicon bar acting as the channel, with heavily doped p+p^+ regions diffused on opposing sides to form gates. Metallic ohmic contacts establish Source and Drain terminals at the ends, while both gate regions are connected internally to form a single Gate terminal.

    • Working Principle: Operating under gate-to-source reverse bias (VGS≤0 VV_{GS} \le 0\,\text{V}), depletion boundaries form along the p-n junctions and penetrate into the lightly doped n-channel. Increasing reverse gate bias widens the non-conductive depletion regions, constricting the physical cross-section of the channel and decreasing carrier conduction.

    • Drain Characteristic Regions:

      • Ohmic / Linear Region (VDS<VGS−VPV_{DS} < V_{GS} - V_P): Channel acts as a voltage-controlled linear resistor.

      • Pinch-Off and Saturation Region (VDS≥VGS−VPV_{DS} \ge V_{GS} - V_P): Depletion boundaries meet at the drain end. The current saturates to a fixed constant level IDI_D.

      • Avalanche Breakdown: At excessive VDSV_{DS}, reverse junction breakdown causes an uncontrolled current surge.

    • Transfer Characteristics: Parabolic transfer curve defined by Shockley's equation:
      ID=IDSS(1−VGSVP)2I_D = I_{DSS}\left(1 - \frac{V_{GS}}{V_P}\right)^2

  2. Construction, Working, and Characteristics of N-Channel DE-MOSFET (7 Marks)

    • Physical Construction: Built on a lightly doped p-type substrate. Two heavily doped n+n^+ regions are diffused to provide source and drain contacts. A physical n-channel connects the source and drain. A dielectric layer of silicon dioxide (SiO2\text{SiO}_2) is grown over the channel, and a metallic gate is deposited on top, preventing DC gate conduction.

    • Depletion-Mode Operation (VGS<0 VV_{GS} < 0\,\text{V}): A negative gate potential repels conduction electrons from the n-channel into the p-substrate and attracts holes, accelerating recombination and depleting channel carriers until pinch-off occurs at VGS=VPV_{GS} = V_P (ID=0 mAI_D = 0\,\text{mA}).

    • Enhancement-Mode Operation (VGS>0 VV_{GS} > 0\,\text{V}): Positive gate voltage attracts additional free electrons from the substrate upward into the pre-existing channel, increasing channel carrier concentration and raising drain current beyond IDSSI_{DSS}.

    • Characteristics: The transfer curve spans both sides of the y-axis, obeying Shockley's equation across depletion (VGS<0 VV_{GS} < 0\,\text{V}) and enhancement (VGS>0 VV_{GS} > 0\,\text{V}) modes continuously.

  3. Construction, Working, and Characteristics of N-Channel E-MOSFET (7 Marks)

    • Physical Construction: Formed on a p-type substrate with two isolated, heavily doped n+n^+ regions for source and drain. No physical channel is fabricated between source and drain. The channel region is covered by an insulating SiO2\text{SiO}_2 dielectric layer beneath a metal/polysilicon gate.

    • Zero Gate Bias (VGS=0 VV_{GS} = 0\,\text{V}): The back-to-back p-n junctions between source, substrate, and drain prevent carrier flow, resulting in ID=0 mAI_D = 0\,\text{mA}.

    • Channel Inversion (VGS≥VTV_{GS} \ge V_T): A positive gate bias repels substrate holes, creating a thin depletion layer. Once VGSV_{GS} reaches threshold voltage (VTV_T), the electric field pulls free minority electrons from the substrate to the surface, creating an n-type inversion layer that bridges source and drain.

    • Saturation and Pinch-Off: As VDSV_{DS} increases such that VDS≥VGS−VTV_{DS} \ge V_{GS} - V_T, channel thickness at the drain end diminishes to pinch-off, causing drain current saturation governed by:
      ID=k(VGS−VT)2I_D = k(V_{GS} - V_T)^2

    • Transfer Characteristics: Current remains strictly zero for all VGS<VTV_{GS} < V_T and grows parabolically for VGS>VTV_{GS} > V_T.

  4. Complementary MOSFET (CMOS) Inverter Architecture and Operation (7 Marks)

    • Circuit Architecture: Integrates an enhancement PMOS transistor and an enhancement NMOS transistor on a monolithic substrate. The source of the PMOS is tied to VSS=5 VV_{SS} = 5\,\text{V}, the source of the NMOS is tied to ground (0 V0\,\text{V}), the gate terminals are tied together as input ViV_i, and both drain terminals are connected as output VoV_o.

    • High Input Condition (Vi=5 VV_i = 5\,\text{V}, Logic 1):

      • NMOS gate bias is VGS1=5 V>VT(NMOS)V_{GS1} = 5\,\text{V} > V_{T(\text{NMOS})}, switching the NMOS ON into a low-resistance conducting state.

      • PMOS gate bias is VGS2=Vi−VSS=5 V−5 V=0 V>VT(PMOS)V_{GS2} = V_i - V_{SS} = 5\,\text{V} - 5\,\text{V} = 0\,\text{V} > V_{T(\text{PMOS})}, switching the PMOS OFF into an open-circuit state.

      • The output node is pulled down to ground through NMOS: Vo=0 VV_o = 0\,\text{V} (Logic 0).

    • Low Input Condition (Vi=0 VV_i = 0\,\text{V}, Logic 0):

      • NMOS gate bias is VGS1=0 V<VT(NMOS)V_{GS1} = 0\,\text{V} < V_{T(\text{NMOS})}, switching NMOS OFF.

      • PMOS gate bias is VGS2=0 V−5 V=−5 V<VT(PMOS)V_{GS2} = 0\,\text{V} - 5\,\text{V} = -5\,\text{V} < V_{T(\text{PMOS})}, switching PMOS ON.

      • The output node is pulled up to VSSV_{SS} through PMOS: Vo=5 VV_o = 5\,\text{V} (Logic 1).

    • Operational Advantage: In steady state, one transistor is always fully non-conducting, ensuring zero static DC power dissipation.

  5. Miller Capacitance Concept and Derivation of Miller Input Capacitance (7 Marks)

    • Miller Phenomenon: In any inverting amplifier with voltage gain −Av-A_v, a physical feedback impedance bridging the input and output nodes draws feedback current proportional to the total voltage excursion across it, presenting an amplified effective capacitance across the input terminals.

    • Mathematical Derivation:
            Let feedback capacitance bridging input and output be Cf=CgdC_f = C_{gd}. Applying Kirchhoff's Current Law at the input node:
      I2=Vi−VoXCfI_2 = \frac{V_i - V_o}{X_{C_f}}
            Substituting output voltage in terms of stage gain (Vo=AvViV_o = A_v V_i):
      I2=Vi−AvViXCf=Vi(1−Av)XCfI_2 = \frac{V_i - A_v V_i}{X_{C_f}} = \frac{V_i(1 - A_v)}{X_{C_f}}
            The effective input reactance XCMiX_{C_{M_i}} seen by input voltage ViV_i is:
      XCMi=ViI2=XCf1−AvX_{C_{M_i}} = \frac{V_i}{I_2} = \frac{X_{C_f}}{1 - A_v}
            Expressing reactance in terms of angular frequency (XC=1ωCX_C = \frac{1}{\omega C}):
      1ωCMi=1ω(1−Av)Cf\frac{1}{\omega C_{M_i}} = \frac{1}{\omega (1 - A_v)C_f}
            Equating capacitances yields the Miller input capacitance expression:
      CMi=(1−Av)Cf=(1−Av)CgdC_{M_i} = (1 - A_v)C_f = (1 - A_v)C_{gd}

    • Impact on Bandwidth: For an inverting amplifier (Av<0A_v < 0), (1−Av)=(1+∣Av∣)(1 - A_v) = (1 + |A_v|), heavily increasing input capacitance and drastically lowering upper cutoff frequency fHif_{H_i}.

  6. Miller Capacitance Concept and Derivation of Miller Output Capacitance (7 Marks)

    • Output Loading Phenomenon: The feedback capacitance also diverts current at the output node, establishing an effective shunt capacitance across the output load terminals.

    • Mathematical Derivation:
            Applying Kirchhoff's Current Law at the amplifier output node:
      Io=Vo−ViXCfI_o = \frac{V_o - V_i}{X_{C_f}}
            Since Vi=VoAvV_i = \frac{V_o}{A_v}, substitute into the current equation:
      Io=Vo−VoAvXCf=Vo(1−1Av)XCfI_o = \frac{V_o - \frac{V_o}{A_v}}{X_{C_f}} = \frac{V_o\left(1 - \frac{1}{A_v}\right)}{X_{C_f}}
            The effective output reactance is:
      XCMo=VoIo=XCf1−1AvX_{C_{M_o}} = \frac{V_o}{I_o} = \frac{X_{C_f}}{1 - \frac{1}{A_v}}
            Substituting capacitive reactance expressions (XC=1ωCX_C = \frac{1}{\omega C}):
      1ωCMo=1ω(1−1Av)Cf\frac{1}{\omega C_{M_o}} = \frac{1}{\omega \left(1 - \frac{1}{A_v}\right)C_f}
            Yielding the Miller output capacitance:
      CMo=(1−1Av)Cf=(1−1Av)CgdC_{M_o} = \left(1 - \frac{1}{A_v}\right)C_f = \left(1 - \frac{1}{A_v}\right)C_{gd}

    • High-Gain Simplification: When the magnitude of stage voltage gain is large (∣Av∣≫1|A_v| \gg 1), the term 1Av≈0\frac{1}{A_v} \approx 0, reducing the output Miller capacitance to:
      CMo≈Cf=CgdC_{M_o} \approx C_f = C_{gd}

  7. Numerical Problem on Miller Capacitance (Cf=10 pFC_f = 10\,\text{pF}, Av=−120A_v = -120) (7 Marks)

    • Given Parameters: Cf=10 pFC_f = 10\,\text{pF}, Av=−120A_v = -120.

    • Step 1: Calculate Miller Input Capacitance (CMiC_{M_i}):
      CMi=(1−Av)Cf=[1−(−120)](10 pF)=(1+120)(10 pF)=121×10 pF=1210 pF=1.21 nFC_{M_i} = (1 - A_v)C_f = [1 - (-120)](10\,\text{pF}) = (1 + 120)(10\,\text{pF}) = 121 \times 10\,\text{pF} = 1210\,\text{pF} = 1.21\,\text{nF}

    • Step 2: Calculate Exact Miller Output Capacitance (CMoC_{M_o}):
      CMo=(1−1Av)Cf=(1−1−120)(10 pF)=(1+1120)(10 pF)=121120×10 pF≈10.083 pFC_{M_o} = \left(1 - \frac{1}{A_v}\right)C_f = \left(1 - \frac{1}{-120}\right)(10\,\text{pF}) = \left(1 + \frac{1}{120}\right)(10\,\text{pF}) = \frac{121}{120} \times 10\,\text{pF} \approx 10.083\,\text{pF}

    • Step 3: Evaluate and Justify Approximation:
            The standard high-gain approximation assumes CMo≈Cf=10 pFC_{M_o} \approx C_f = 10\,\text{pF}.
            The percentage deviation between the exact value and the approximation is:
      Error=10.083 pF−10.0 pF10.083 pF×100%=0.08310.083×100%≈0.82%\text{Error} = \frac{10.083\,\text{pF} - 10.0\,\text{pF}}{10.083\,\text{pF}} \times 100\% = \frac{0.083}{10.083} \times 100\% \approx 0.82\%

    • Conclusion: Yes, this is an excellent approximation. Because ∣Av∣=120≫1|A_v| = 120 \gg 1, the fractional error is well below 1%1\%, which falls comfortably within standard industrial component tolerances.


2. Module 2: Power Amplifiers, Feedback Topologies, and Oscillators
Unit 1: Power Amplifiers and RC Oscillators (7 Marks Each)
  1. Series-Fed Class A Power Amplifier: Circuit and Maximum Efficiency of 25% (7 Marks)

    • Circuit Description: A power BJT is connected in series with collector load resistor RCR_C and DC supply VCCV_{CC}, with the transistor biased to operate in active mode for the full 360∘360^\circ input signal cycle.

    • DC Input Power (Pi(dc)P_{i(\text{dc})}):
      Pi(dc)=VCCICQP_{i(\text{dc})} = V_{CC} I_{CQ}
           For maximum symmetrical voltage and current swings:
      VCEQ=VCC2,ICQ=IC(sat)2=VCC2RCV_{CEQ} = \frac{V_{CC}}{2}, \quad I_{CQ} = \frac{I_{C(\text{sat})}}{2} = \frac{V_{CC}}{2R_C}
      Pi(dc)=VCC(VCC2RC)=VCC22RCP_{i(\text{dc})} = V_{CC}\left(\frac{V_{CC}}{2R_C}\right) = \frac{V_{CC}^2}{2R_C}

    • Maximum AC Output Power (Po(ac)P_{o(\text{ac})}):
           Using RMS values for sinusoidal signals:
      Po(ac)=Vo(peak)22RCP_{o(\text{ac})} = \frac{V_{o(\text{peak})}^2}{2R_C}
           The maximum unclipped peak voltage swing is Vo(peak)=VCC2V_{o(\text{peak})} = \frac{V_{CC}}{2}:
      Po(ac,max⁡)=(VCC2)22RC=VCC28RCP_{o(\text{ac},\max)} = \frac{\left(\frac{V_{CC}}{2}\right)^2}{2R_C} = \frac{V_{CC}^2}{8R_C}

    • Maximum Conversion Efficiency (\eta_{\max}):
      ηmax⁡=Po(ac,max⁡)Pi(dc)×100%=VCC28RCVCC22RC×100%=28×100%=25%\eta_{\max} = \frac{P_{o(\text{ac},\max)}}{P_{i(\text{dc})}} \times 100\% = \frac{\frac{V_{CC}^2}{8R_C}}{\frac{V_{CC}^2}{2R_C}} \times 100\% = \frac{2}{8} \times 100\% = 25\%

  2. Transformer-Coupled Class A Power Amplifier: Operation and Efficiency of 50% (7 Marks)

    • Circuit Operation: A step-down transformer couples collector signal swing to load resistance RLR_L. The primary winding has near-zero DC winding resistance, preventing DC power waste.

    • DC Operating Point: The DC load line is vertical, fixing quiescent collector voltage at VCEQ=VCCV_{CEQ} = V_{CC}.

    • DC Input Power:
      Pi(dc)=VCCICQP_{i(\text{dc})} = V_{CC} I_{CQ}

    • Maximum AC Output Power:
           Due to transformer inductive action, collector voltage can swing symmetrically from 0 V0\,\text{V} up to 2VCC2V_{CC}. Peak AC voltage is Vo(peak)=VCCV_{o(\text{peak})} = V_{CC}, and peak AC current is Io(peak)=ICQI_{o(\text{peak})} = I_{CQ}:
      Po(ac,max⁡)=Vo(peak)Io(peak)2=VCCICQ2P_{o(\text{ac},\max)} = \frac{V_{o(\text{peak})} I_{o(\text{peak})}}{2} = \frac{V_{CC} I_{CQ}}{2}

    • Conversion Efficiency:
      ηmax⁡=Po(ac,max⁡)Pi(dc)×100%=VCCICQ2VCCICQ×100%=50%\eta_{\max} = \frac{P_{o(\text{ac},\max)}}{P_{i(\text{dc})}} \times 100\% = \frac{\frac{V_{CC} I_{CQ}}{2}}{V_{CC} I_{CQ}} \times 100\% = 50\%

  3. Class B Push-Pull Amplifier: Operation and Maximum Efficiency of 78.5% (7 Marks)

    • Circuit Operation: Employs two matched transistors biased at cutoff (VBE=0 V,ICQ=0 AV_{BE} = 0\,\text{V}, I_{CQ} = 0\,\text{A}). Each transistor conducts for exactly one half-cycle (180∘180^\circ).

    • DC Supply Input Power: For full sinusoidal output with peak current IpI_p, the DC supply delivers a full-wave rectified current profile whose average value is Idc=2πIpI_{\text{dc}} = \frac{2}{\pi} I_p:
      Pi(dc)=VCCIdc=2πVCCIpP_{i(\text{dc})} = V_{CC} I_{\text{dc}} = \frac{2}{\pi} V_{CC} I_p

    • AC Output Power: Across load RLR_L:
      Po(ac)=VpIp2P_{o(\text{ac})} = \frac{V_p I_p}{2}
           For maximum voltage swing without clipping, Vp=VCCV_p = V_{CC}:
      Po(ac,max⁡)=VCCIp2P_{o(\text{ac},\max)} = \frac{V_{CC} I_p}{2}

    • Conversion Efficiency:
      ηmax⁡=Po(ac,max⁡)Pi(dc)×100%=VCCIp22πVCCIp×100%=π4×100%≈78.54%\eta_{\max} = \frac{P_{o(\text{ac},\max)}}{P_{i(\text{dc})}} \times 100\% = \frac{\frac{V_{CC} I_p}{2}}{\frac{2}{\pi} V_{CC} I_p} \times 100\% = \frac{\pi}{4} \times 100\% \approx 78.54\%

  4. Transformer-Coupled Push-Pull Class B Amplifier (7 Marks)

    • Circuit Architecture: Features an input center-tapped transformer driving two identical NPN transistors in anti-phase, with an output center-tapped transformer combining collector currents into load RLR_L.

    • Half-Cycle Conduction: During the positive input half-cycle, secondary voltage turns Q1Q_1 ON and Q2Q_2 OFF. During the negative half-cycle, secondary polarity inverts, driving Q2Q_2 ON and Q1Q_1 OFF.

    • Harmonic Cancellation: Center-tapped output transformer forces currents to flow in opposite directions through primary windings, canceling all even harmonic distortion components and core DC flux saturation.

    • Efficiency and Rating: Delivers up to 78.5%78.5\% efficiency while ensuring zero standby DC power consumption when no AC input is present.

  5. Complementary Symmetry Push-Pull Class B Amplifier (7 Marks)

    • Circuit Description: Eliminates bulky transformers by using a complementary matched pair of one NPN transistor (Q1Q_1) and one PNP transistor (Q2Q_2) with bases and emitters tied together.

    • Symmetrical Operation: Under split supplies (±VCC\pm V_{CC}), a positive input swing forward-biases NPN transistor Q1Q_1 (conducting into load), while reverse-biasing PNP transistor Q2Q_2. A negative input swing forward-biases PNP transistor Q2Q_2 (sinking load current to −VCC-V_{CC}), while keeping Q1Q_1 OFF.

    • Advantages: Eliminates bulky, costly transformers, exhibits flat wideband frequency response, and supports monolithic IC integration.

    • Disadvantages: Requires perfectly matched NPN and PNP complementary characteristics, dual power rails (or output capacitor coupling), and generates crossover distortion near zero-crossing.

  6. Elimination of Crossover Distortion in Complementary Symmetry Circuits (7 Marks)

    • Origin of Crossover Distortion: Occurs because standard silicon transistors require a threshold voltage (VBE≈0.7 VV_{BE} \approx 0.7\,\text{V}) to initiate base conduction. In pure Class B biasing, both transistors remain OFF in the window −0.7 V<Vi<0.7 V-0.7\,\text{V} < V_i < 0.7\,\text{V}, producing flat zero-output intervals at signal zero-crossings.

    • Elimination Method (Class AB Biasing): A small forward bias voltage (≈1.4 V\approx 1.4\,\text{V} total) is placed between the bases of Q1Q_1 and Q2Q_2 using two series-connected forward-biased p-n junction diodes (or an active VBEV_{BE} multiplier circuit).

    • Action: Biasing maintains both transistors slightly ON under quiescent conditions (ICQ>0I_{CQ} > 0), bridging the cut-in dead band and ensuring continuous conduction across signal transitions without introducing significant idle power loss.

  7. Harmonic Distortion and Three-Point Method (7 Marks)

    • Definition: Non-linear transistor transfer curves distort pure sinusoidal signals by generating integer multiple frequencies (harmonics: 2f,3f,…2f, 3f, \dots).

    • Three-Point Calculation: Evaluates dynamic output collector current waveform at three critical points on the load line: positive peak (Imax⁡I_{\max}), negative trough (Imin⁡I_{\min}), and quiescent level (ICQI_{CQ}).

    • Fundamental and Second Harmonic Amplitudes:
      Ic1=Imax⁡−Imin⁡2I_{c1} = \frac{I_{\max} - I_{\min}}{2}
      Ic2=Imax⁡+Imin⁡−2ICQ4I_{c2} = \frac{I_{\max} + I_{\min} - 2I_{CQ}}{4}

    • Second Harmonic Distortion (D2D_2):
      D2=∣Ic2Ic1∣=∣Imax⁡+Imin⁡−2ICQ2(Imax⁡−Imin⁡)∣×100%D_2 = \left|\frac{I_{c2}}{I_{c1}}\right| = \left|\frac{I_{\max} + I_{\min} - 2I_{CQ}}{2(I_{\max} - I_{\min})}\right| \times 100\%

  8. Derive Expression for Second Harmonic Distortion (7 Marks)

    • Power Series Expansion: A non-linear active device transfers input AC voltage vi=Vmcos⁡(ωt)v_i = V_m \cos(\omega t) to output current via a Taylor expansion:
      iC=ICQ+a1vi+a2vi2i_C = I_{CQ} + a_1 v_i + a_2 v_i^2

    • Trigonometric Substitution:
      iC=ICQ+a1Vmcos⁡(ωt)+a2Vm2cos⁡2(ωt)i_C = I_{CQ} + a_1 V_m \cos(\omega t) + a_2 V_m^2 \cos^2(\omega t)
           Using identity cos⁡2(ωt)=1+cos⁡(2ωt)2\cos^2(\omega t) = \frac{1 + \cos(2\omega t)}{2}:
      iC=(ICQ+a2Vm22)+a1Vmcos⁡(ωt)+a2Vm22cos⁡(2ωt)i_C = \left(I_{CQ} + \frac{a_2 V_m^2}{2}\right) + a_1 V_m \cos(\omega t) + \frac{a_2 V_m^2}{2} \cos(2\omega t)

    • Component Isolation:

      • Quiescent/DC shift: Idc=ICQ+a2Vm22I_{\text{dc}} = I_{CQ} + \frac{a_2 V_m^2}{2}

      • Fundamental amplitude: I1=a1VmI_1 = a_1 V_m

      • Second harmonic amplitude: I2=a2Vm22I_2 = \frac{a_2 V_m^2}{2}

    • Evaluating Waveform Extrema:

      • At ωt=0\omega t = 0: Imax⁡=ICQ+a1Vm+a2Vm2I_{\max} = I_{CQ} + a_1 V_m + a_2 V_m^2

      • At ωt=π\omega t = \pi: Imin⁡=ICQ−a1Vm+a2Vm2I_{\min} = I_{CQ} - a_1 V_m + a_2 V_m^2

    • Solving for Coefficients:
      Imax⁡−Imin⁡=2a1Vm=2I1  ⟹  I1=Imax⁡−Imin⁡2I_{\max} - I_{\min} = 2a_1 V_m = 2I_1 \implies I_1 = \frac{I_{\max} - I_{\min}}{2}
      Imax⁡+Imin⁡−2ICQ=2a2Vm2=4I2  ⟹  I2=Imax⁡+Imin⁡−2ICQ4I_{\max} + I_{\min} - 2I_{CQ} = 2a_2 V_m^2 = 4I_2 \implies I_2 = \frac{I_{\max} + I_{\min} - 2I_{CQ}}{4}

    • Percentage Distortion:
      D2=I2I1×100%=Imax⁡+Imin⁡−2ICQ2(Imax⁡−Imin⁡)×100%D_2 = \frac{I_2}{I_1} \times 100\% = \frac{I_{\max} + I_{\min} - 2I_{CQ}}{2(I_{\max} - I_{\min})} \times 100\%

  9. Operation of Class C and Class D Amplifiers (7 Marks)

    • Class C Amplifier: Transistor is biased beyond cutoff such that conduction occurs for less than a half cycle (conduction angle θ<180∘\theta < 180^\circ, typically 120∘120^\circ to 150∘150^\circ). The output current pulses excite a high-Q parallel LC tank circuit tuned to the input frequency, which filters pulses into a clean sinusoidal wave via the flywheel effect. Efficiency reaches 80%80\% to 90%90\%.

    • Class D Amplifier: Operates transistors as digital switches (either fully ON or fully OFF) using pulse-width modulation (PWM). When ON, device voltage drop is near zero; when OFF, current is zero, achieving theoretical efficiency near 100%100\%. A passive low-pass LC filter reconstructs the amplified analog signal.

  10. Numerical: Voltage Gain With and Without Feedback (7 Marks)

    • Given Parameters: gm=5 mSg_m = 5\,\text{mS}, RD=5.1 kΩR_D = 5.1\,\text{k}\Omega, RS=1 kΩR_S = 1\,\text{k}\Omega, RF=20 kΩR_F = 20\,\text{k}\Omega.

    • Gain Without Feedback (AA): For an unbypassed source resistor in voltage-series configuration, the open-loop gain is:
      A=−gmRD=−(5 mS)(5.1 kΩ)=−25.5A = -g_m R_D = -(5\,\text{mS})(5.1\,\text{k}\Omega) = -25.5

    • Feedback Attenuation Factor (\beta): Feedback voltage across source resistor RSR_S from divider network:
      β=RSRS+RF=1 kΩ1 kΩ+20 kΩ=121≈0.0476\beta = \frac{R_S}{R_S + R_F} = \frac{1\,\text{k}\Omega}{1\,\text{k}\Omega + 20\,\text{k}\Omega} = \frac{1}{21} \approx 0.0476

    • Gain With Feedback (AfA_f):
      Af=A1+β∣A∣=−25.51+(0.0476)(25.5)=−25.51+1.214=−25.52.214≈−11.52A_f = \frac{A}{1 + \beta |A|} = \frac{-25.5}{1 + (0.0476)(25.5)} = \frac{-25.5}{1 + 1.214} = \frac{-25.5}{2.214} \approx -11.52

  11. Op-Amp RC Phase Shift Oscillator Operation and Role of 3 Stages (7 Marks)

    • Operational Principle: Consists of an operational amplifier operating in inverting mode, providing a 180∘180^\circ phase shift between input and output.

    • Barkhausen Phase Requirement: To satisfy the Barkhausen criterion of 360∘360^\circ (or 0∘0^\circ) total loop phase shift, the feedback network must produce an additional 180∘180^\circ phase inversion at the oscillation frequency fof_o.

    • Requirement of Three RC Stages: A single passive RC section can produce a theoretical maximum phase shift approaching 90∘90^\circ, but at non-zero signal attenuation it yields roughly 60∘60^\circ. Therefore, a minimum of three cascaded RC stages is necessary, with each section contributing 60∘60^\circ to total 180∘180^\circ (3×60∘=180∘3 \times 60^\circ = 180^\circ).

    • Oscillation Frequency Expression:
      fo=12πRC6f_o = \frac{1}{2\pi R C \sqrt{6}}

    • Gain Requirement: The RC feedback ladder attenuates the signal by a factor of β=129\beta = \frac{1}{29}. To satisfy ∣Aβ∣=1|A\beta| = 1, the inverting op-amp must be configured for a closed-loop gain magnitude of:
      ∣A∣=RfR1≥29|A| = \frac{R_f}{R_1} \ge 29


Unit 2: Feedback Topologies and Resonant Oscillators (7 Marks Each)
  1. Classification of Four Basic Negative Feedback Topologies (7 Marks)

    • Sampling and Mixing Principles: Output sampling is categorized as either Voltage (parallel connection across the load) or Current (series connection in line with the load). Input mixing is categorized as either Series (feedback voltage subtracted from input voltage loop) or Shunt (feedback current subtracted from input current node).

    • Topologies:

    1. Voltage-Series Feedback (Series-Shunt): Samples output voltage (VoV_o), mixes in series with input signal (VsV_s).

    2. Voltage-Shunt Feedback (Shunt-Shunt): Samples output voltage (VoV_o), mixes in parallel with input signal current (IsI_s).

    3. Current-Series Feedback (Series-Series): Samples output load current (IoI_o), mixes in series with input voltage (VsV_s).

    4. Current-Shunt Feedback (Shunt-Series): Samples output load current (IoI_o), mixes in parallel with input current (IsI_s).

  2. Voltage-Series Feedback: Block Diagram, Impedances, and Gain (7 Marks)

    • Configuration: Output voltage VoV_o is sampled and fed back as Vf=βVoV_f = \beta V_o in series opposition to signal VsV_s, so that net amplifier input is Vi=Vs−VfV_i = V_s - V_f.

    • Closed-Loop Gain (AfA_f):
      Vo=AVi=A(Vs−βVo)  ⟹  Vo(1+βA)=AVsV_o = A V_i = A(V_s - \beta V_o) \implies V_o(1 + \beta A) = A V_s
      Af=VoVs=A1+βAA_f = \frac{V_o}{V_s} = \frac{A}{1 + \beta A}

    • Input Impedance with Feedback (ZifZ_{if}):
      Vs=IiZi+Vf=IiZi+β(AIiZi)=IiZi(1+βA)V_s = I_i Z_i + V_f = I_i Z_i + \beta(A I_i Z_i) = I_i Z_i(1 + \beta A)
      Zif=VsIi=Zi(1+βA)Z_{if} = \frac{V_s}{I_i} = Z_i(1 + \beta A)
           Negative voltage-series feedback increases input impedance by the desensitivity factor (1+βA)(1 + \beta A).

    • Output Impedance with Feedback (ZofZ_{of}): Evaluated by shorting the source (Vs=0V_s = 0) and applying external test voltage VV:
      Zof=Zo1+βAZ_{of} = \frac{Z_o}{1 + \beta A}
           Decreases output impedance by (1+βA)(1 + \beta A), stabilizing output voltage against load variations.

  3. Voltage-Shunt Feedback Operation and Impedance Modifications (7 Marks)

    • Operation: Output voltage is sampled and feedback current If=βVoI_f = \beta V_o is injected into the input node in parallel opposition to input current IsI_s:
      Ii=Is−If=Is−βVoI_i = I_s - I_f = I_s - \beta V_o

    • Closed-Loop Transresistance Gain:
      Rmf=VoIs=Rm1+βRmR_{mf} = \frac{V_o}{I_s} = \frac{R_m}{1 + \beta R_m}

    • Input Impedance Modification: Shunt mixing at the input draws away current, lowering the input impedance:
      Zif=Zi1+βRmZ_{if} = \frac{Z_i}{1 + \beta R_m}

    • Output Impedance Modification: Voltage sampling across the output maintains voltage regulation, reducing the output impedance:
      Zof=Zo1+βRmZ_{of} = \frac{Z_o}{1 + \beta R_m}

    • Summary: Voltage-shunt feedback reduces both input and output impedances.

  4. Wien Bridge Oscillator Operation and Frequency Derivation (7 Marks)

    • Architecture: Employs an op-amp configured as a non-inverting amplifier (0∘0^\circ phase shift) with a lead-lag RC bridge network in its feedback loop. The series arm contains R1,C1R_1, C_1 and the parallel arm contains R2,C2R_2, C_2.

    • Feedback Transfer Ratio (β\beta):
      β(s)=ZpZs+Zp\beta(s) = \frac{Z_p}{Z_s + Z_p}
           where Zs=R+1sC=sRC+1sCZ_s = R + \frac{1}{sC} = \frac{sRC + 1}{sC} and Zp=R∥1sC=RsRC+1Z_p = R \parallel \frac{1}{sC} = \frac{R}{sRC + 1}.

    • Simplification with Equal Components (R1=R2=R,C1=C2=CR_1 = R_2 = R, C_1 = C_2 = C):
      β(jω)=jωRC1−ω2R2C2+3jωRC\beta(j\omega) = \frac{j\omega RC}{1 - \omega^2 R^2 C^2 + 3j\omega RC}

    • Resonant Frequency Condition: For the feedback network to provide zero phase shift, the imaginary component of the denominator must vanish, requiring the denominator to be purely real:

            1−ωo2R2C2=0  ⟹  ωo=1RC1 - \omega_o^2 R^2 C^2 = 0 \implies \omega_o = \frac{1}{RC}
      fo=12πRCf_o = \frac{1}{2\pi R C}

    • Gain Condition: At ω=ωo\omega = \omega_o, the feedback ratio reduces to β=jωRC3jωRC=13\beta = \frac{j\omega RC}{3j\omega RC} = \frac{1}{3}. To satisfy ∣Aβ∣=1|A\beta| = 1, the non-inverting op-amp closed-loop gain must be:
      A=1+RfR1≥3  ⟹  RfR1≥2A = 1 + \frac{R_f}{R_1} \ge 3 \implies \frac{R_f}{R_1} \ge 2

  5. Comparison of Colpitts and Hartley Oscillators and Frequency Derivation (7 Marks)

    • Comparative Structure:

      • Hartley Oscillator: Employs two tapped inductors (L1,L2L_1, L_2) and one tuning capacitor (CC) in its feedback tank. Feedback is taken via an inductive voltage divider.

      • Colpitts Oscillator: Employs two tapped capacitors (C1,C2C_1, C_2) and one inductor (LL) in its feedback tank. Feedback is derived via a capacitive voltage divider.

    • High-Frequency Performance: Colpitts is superior at high frequencies because its capacitive divider absorbs internal transistor parasitic capacitances (Cbe,CceC_{be}, C_{ce}), while Hartley inductors suffer from stray winding capacitance.

    • Derivation of Resonant Frequency for Colpitts Oscillator: The feedback network requires three reactive impedances satisfying:
      X1+X2+X3=0X_1 + X_2 + X_3 = 0
           where X1=1ωC1X_1 = \frac{1}{\omega C_1}, X2=1ωC2X_2 = \frac{1}{\omega C_2}, and X3=ωLX_3 = \omega L:
      −1ωC1−1ωC2+ωL=0  ⟹  ωL=1ω(1C1+1C2)-\frac{1}{\omega C_1} - \frac{1}{\omega C_2} + \omega L = 0 \implies \omega L = \frac{1}{\omega}\left(\frac{1}{C_1} + \frac{1}{C_2}\right)
      ωo2=1L(C1+C2C1C2)=1LCeq\omega_o^2 = \frac{1}{L}\left(\frac{C_1 + C_2}{C_1 C_2}\right) = \frac{1}{L C_{\text{eq}}}
      fo=12πLCeqwhere Ceq=C1C2C1+C2f_o = \frac{1}{2\pi \sqrt{L C_{\text{eq}}}} \quad \text{where } C_{\text{eq}} = \frac{C_1 C_2}{C_1 + C_2}

  6. Derivation of Wien Bridge Sustained Oscillation Condition (A≥3A \ge 3) (7 Marks)

    • Setting the transfer function of the RC bridge at resonance:
      β(ωo)=13\beta(\omega_o) = \frac{1}{3}

    • For sustained oscillations, Barkhausen's loop gain magnitude must equal unity:
      ∣Aβ∣=1  ⟹  A(13)=1  ⟹  A=3|A\beta| = 1 \implies A\left(\frac{1}{3}\right) = 1 \implies A = 3

    • For non-inverting op-amp configuration:
      A=1+RfR1=3  ⟹  RfR1=2A = 1 + \frac{R_f}{R_1} = 3 \implies \frac{R_f}{R_1} = 2

    • To guarantee initial build-up from circuit thermal noise, loop gain must initially slightly exceed unity (A>3A > 3), stabilizing to A=3A = 3 as output reaches rated steady-state amplitude.

  7. Colpitts AC Model and Feedback Attenuation Factor (7 Marks)

    • AC Equivalent Circuit: The transistor is represented by input resistance hieh_{ie} and current source hfeibh_{fe} i_b. The tank circuit is connected between collector and ground, with capacitor C2C_2 shunting the output and C1C_1 returning to the base.

    • Feedback Attenuation (\beta): Capacitors C1C_1 and C2C_2 form an AC voltage divider across the inductor:
      β=VfVo=XC1XC2=1ωC11ωC2=C2C1\beta = \frac{V_f}{V_o} = \frac{X_{C_1}}{X_{C_2}} = \frac{\frac{1}{\omega C_1}}{\frac{1}{\omega C_2}} = \frac{C_2}{C_1}

    • Condition for Sustained Oscillation: For a BJT amplifier, the minimum forward current gain required to overcome tank losses is:
      hfe≥C1C2h_{fe} \ge \frac{C_1}{C_2}

  8. Design of a Wien Bridge Oscillator (f=2.5 kHzf = 2.5\,\text{kHz}, C=0.01 μFC = 0.01\,\mu\text{F}) (7 Marks)

    • Given Parameters: fo=2.5 kHz=2500 Hzf_o = 2.5\,\text{kHz} = 2500\,\text{Hz}, C=0.01 μF=0.01×10−6 FC = 0.01\,\mu\text{F} = 0.01 \times 10^{-6}\,\text{F}.

    • Step 1: Calculate Required Resistance (RR):
      fo=12πRC  ⟹  R=12πfoCf_o = \frac{1}{2\pi R C} \implies R = \frac{1}{2\pi f_o C}
      R=12π×2500×(0.01×10−6)=12π×2.5×10−5=1055π=20000π≈6366.2 Ω≈6.37 kΩR = \frac{1}{2\pi \times 2500 \times (0.01 \times 10^{-6})} = \frac{1}{2\pi \times 2.5 \times 10^{-5}} = \frac{10^5}{5\pi} = \frac{20000}{\pi} \approx 6366.2\,\Omega \approx 6.37\,\text{k}\Omega

    • Step 2: Determine Feedback Resistor Ratio (\frac{R_f}{R_1}):
           The non-inverting op-amp must have an open-loop gain of at least 33 to compensate for the bridge attenuation of β=13\beta = \frac{1}{3}:
      A=1+RfR1≥3  ⟹  RfR1≥2A = 1 + \frac{R_f}{R_1} \ge 3 \implies \frac{R_f}{R_1} \ge 2

    • Step 3: Component Selection:
           Select standard resistor values: choose R1=10 kΩR_1 = 10\,\text{k}\Omega, then Rf=2R1=20 kΩR_f = 2R_1 = 20\,\text{k}\Omega (or a potentiometer up to 22 kΩ22\,\text{k}\Omega to adjust loop gain and ensure reliable startup).


Unit 3: Feedback Characteristics and Advanced Oscillators (6 Marks Each)
  1. Current-Series Feedback Behavior and Impedance Changes (6 Marks)

    • Topology: Output current IoI_o is sampled by passing it through a series resistor, developing feedback voltage Vf=βIoV_f = \beta I_o that subtracts in series from input loop voltage VsV_s.

    • Effect on Input Resistance (ZifZ_{if}): The feedback voltage opposes applied source voltage, reducing input current for a given signal:
      Zif=Zi(1+βA)Z_{if} = Z_i(1 + \beta A)
           Input impedance is increased by desensitivity factor (1+βA)(1 + \beta A).

    • Effect on Output Resistance (ZofZ_{of}): Output current sampling causes the circuit to act as a regulated, constant-current generator, increasing output impedance:
      Zof=Zo(1+βA)Z_{of} = Z_o(1 + \beta A)

  2. Mathematical Proof: Negative Feedback Reduces Distortion and Extends Bandwidth (6 Marks)

    • Reduction of Non-Linear Distortion: Let open-loop amplifier distortion be DD. Introducing negative feedback reduces output distortion to DfD_f:
      Df=D−βADf  ⟹  Df(1+βA)=D  ⟹  Df=D1+βAD_f = D - \beta A D_f \implies D_f(1 + \beta A) = D \implies D_f = \frac{D}{1 + \beta A}
           Distortion is attenuated by the factor (1+βA)(1 + \beta A).

    • Bandwidth Expansion: Lower cutoff frequency is decreased:
      fLf=fL1+βAf_{Lf} = \frac{f_L}{1 + \beta A}
           Upper cutoff frequency is increased:
      fHf=fH(1+βA)f_{Hf} = f_H(1 + \beta A)
           New bandwidth is:
      BWf=fHf−fLf≈fH(1+βA)=BW(1+βA)BW_f = f_{Hf} - f_{Lf} \approx f_H(1 + \beta A) = BW(1 + \beta A)
           The gain-bandwidth product remains invariant.

  3. Numerical: Gain Sensitivity with Negative Feedback (6 Marks)

    • Given Parameters: Open-loop gain A=−1000A = -1000, feedback fraction β=−0.1\beta = -0.1, fractional open-loop change dAA=20%=0.20\frac{dA}{A} = 20\% = 0.20.

    • Sensitivity Relation: Differentiating closed-loop gain Af=A1+βAA_f = \frac{A}{1 + \beta A} with respect to AA yields:
      dAfAf=11+βA(dAA)\frac{dA_f}{A_f} = \frac{1}{1 + \beta A} \left(\frac{dA}{A}\right)

    • Calculation:
      1+βA=1+(−0.1)(−1000)=1+100=1011 + \beta A = 1 + (-0.1)(-1000) = 1 + 100 = 101
      dAfAf=20%101=0.20101≈0.00198=0.198%\frac{dA_f}{A_f} = \frac{20\%}{101} = \frac{0.20}{101} \approx 0.00198 = 0.198\%

    • Conclusion: A 20%20\% variation in internal transistor open-loop gain results in only a 0.198%0.198\% change in the closed-loop gain.

  4. Numerical: Open-Loop Gain and Bandwidth Determination (6 Marks)

    • Given Parameters: Closed-loop gain Af=40A_f = 40, closed-loop bandwidth BWf=500 kHzBW_f = 500\,\text{kHz}, feedback factor β=0.02\beta = 0.02.

    • Step 1: Calculate Open-Loop Gain (AA):
      Af=A1+βA  ⟹  40=A1+0.02AA_f = \frac{A}{1 + \beta A} \implies 40 = \frac{A}{1 + 0.02A}
      40(1+0.02A)=A  ⟹  40+0.8A=A  ⟹  0.2A=40  ⟹  A=400.2=20040(1 + 0.02A) = A \implies 40 + 0.8A = A \implies 0.2A = 40 \implies A = \frac{40}{0.2} = 200

    • Step 2: Calculate Desensitivity Factor (1+βA1 + \beta A):
      1+βA=1+0.02(200)=1+4=51 + \beta A = 1 + 0.02(200) = 1 + 4 = 5

    • Step 3: Determine Open-Loop Bandwidth (BWBW):
      BWf=BW(1+βA)  ⟹  BW=BWf1+βA=500 kHz5=100 kHzBW_f = BW(1 + \beta A) \implies BW = \frac{BW_f}{1 + \beta A} = \frac{500\,\text{kHz}}{5} = 100\,\text{kHz}

  5. Barkhausen Criterion for Sustained Oscillations (6 Marks)

    • Statement: An electronic circuit will generate steady, continuous sinusoidal oscillations without an external input if and only if two fundamental conditions are met at the oscillation frequency fof_o:

    1. Loop Gain Magnitude:
      ∣βA∣=1|\beta A| = 1

    2. Total Loop Phase Shift:
      ∠(βA)=0∘or 360∘(or integer multiples of 2π)\angle(\beta A) = 0^\circ \quad \text{or } 360^\circ \quad \text{(or integer multiples of } 2\pi\text{)}

    • Physical Significance:

      • If ∣βA∣<1|\beta A| < 1, oscillations die out exponentially due to energy dissipation.

      • If ∣βA∣>1|\beta A| > 1, oscillation amplitude grows exponentially until transistor non-linear saturation limits it.

      • If ∣βA∣=1|\beta A| = 1, energy fed back precisely equals energy dissipated, maintaining a constant steady-state amplitude.

      • The phase condition ensures positive (regenerative) feedback so that the returning signal reinforces the initial disturbance.

  6. Working of Hartley Oscillator and Feedback Role (6 Marks)

    • Circuit Mechanism: An active amplifying stage (BJT, FET, or op-amp) provides a 180∘180^\circ phase shift. The parallel tank network consists of two series inductors (L1,L2L_1, L_2) with a grounded center-tap and a parallel capacitor (CC), providing the returning 180∘180^\circ phase inversion.

    • Resonant Frequency Expression:
      fo=12πLeqCwhere Leq=L1+L2f_o = \frac{1}{2\pi \sqrt{L_{\text{eq}} C}} \quad \text{where } L_{\text{eq}} = L_1 + L_2

    • Role of Feedback Network: Inductor L1L_1 develops output tank voltage, while inductor L2L_2 feeds a fraction of this voltage back to the input in positive phase to maintain oscillations.

  7. RC Phase-Shift Ladder Network Requirements (6 Marks)

    • Phase Distribution: An inverting op-amp introduces a phase shift of 180∘180^\circ. To fulfill the Barkhausen loop criterion of 360∘360^\circ, the passive RC ladder must provide an additional 180∘180^\circ phase shift.

    • Why Three Stages are Essential: A single RC network can produce a theoretical maximum phase shift of 90∘90^\circ, but at that limit the signal attenuation approaches infinity (Vo→0V_o \rightarrow 0). A practical single-stage RC network operates near 60∘60^\circ. Cascading three identical stages provides:
      ϕtotal=3×60∘=180∘\phi_{\text{total}} = 3 \times 60^\circ = 180^\circ
           Two stages can yield at most 180∘180^\circ only at infinite frequency and total signal loss, making three cascaded sections the minimum requirement for sinusoidal oscillation.

  8. Wien Bridge Dual Feedback Mechanisms (6 Marks)

    • Positive Feedback for Oscillation: The series-parallel RC bridge network provides regenerative positive feedback to the non-inverting op-amp terminal. At the resonant frequency fo=12πRCf_o = \frac{1}{2\pi R C}, phase shift through the bridge is 0∘0^\circ, satisfying the Barkhausen phase criterion and initiating oscillations.

    • Negative Feedback for Amplitude Stabilization: A resistive voltage divider (Rf,R1R_f, R_1) supplies negative feedback to the inverting input terminal. This limits loop gain to:
      A=1+RfR1=3A = 1 + \frac{R_f}{R_1} = 3
           By incorporating a non-linear tungsten lamp, thermistor, or JFET in the negative feedback path, any increase in output amplitude raises feedback resistance, automatically returning loop gain to ∣βA∣=1|\beta A| = 1 and eliminating clipping distortion.

  9. Hartley Oscillator with Mutual Inductance (MM) (6 Marks)

    • Coupled Inductor Formulation: When inductors L1L_1 and L2L_2 are wound on a shared core, magnetic coupling introduces mutual inductance MM.

    • Effective Tank Inductance: Because circulating tank current passes through both coils in the same magnetic orientation (aiding coupling):
      Leq=L1+L2+2ML_{\text{eq}} = L_1 + L_2 + 2M

    • Resonant Frequency Expression:
      fo=12π(L1+L2+2M)Cf_o = \frac{1}{2\pi \sqrt{(L_1 + L_2 + 2M)C}}

    • Circuit Role: Mutual inductance increases effective inductance, lowering the resonant frequency and strengthening feedback coupling between output and input.

  10. Comparative Analysis: Hartley vs. Colpitts Oscillators (6 Marks)

    • Tank Circuit Elements: Hartley uses two tapped inductors (L1,L2L_1, L_2) and one capacitor (CC). Colpitts uses two tapped capacitors (C1,C2C_1, C_2) and one inductor (LL).

    • Feedback Division Mechanism: Hartley employs inductive voltage division (feedback ratio β=L2L1\beta = \frac{L_2}{L_1}); Colpitts employs capacitive voltage division (feedback ratio β=C1C2\beta = \frac{C_1}{C_2}).

    • Suitability for High Frequencies: Colpitts is significantly superior at high radio frequencies (VHF/UHF) because its capacitive divider absorbs internal transistor parasitic capacitances (Cbe,CceC_{be}, C_{ce}). Hartley inductors suffer from stray winding capacitance, making Colpitts much more stable at elevated frequencies.

  11. Crystal Oscillator Operation and High Frequency Stability (6 Marks)

    • Operation: Utilizes a piezoelectric quartz crystal behaving as a high-Q electromechanical resonant tank. Its electrical equivalent circuit consists of series R,L,CR, L, C branches shunted by mounting capacitance CMC_M. The crystal can oscillate at series resonance (fs=12πLCf_s = \frac{1}{2\pi\sqrt{LC}}) or parallel resonance (fp=12πLCeqf_p = \frac{1}{2\pi\sqrt{L C_{\text{eq}}}}).

    • Reasons for Exceptional Frequency Stability:

      1. Extremely High Quality Factor (QQ): Ranges from 10410^4 to 10610^6 (compared to Q≈102Q \approx 10^2 for LC tanks), providing an extraordinarily steep phase-frequency slope (dϕdω\frac{d\phi}{d\omega}) that strongly resists frequency drift.

      2. Thermal Rigidity: Specially cut quartz (such as AT-cut) exhibits near-zero temperature coefficients over wide operating bands.

      3. Physical Durability: Mechanical hardness and chemical inertness eliminate aging-induced parameter drift.

  12. Op-Amp Implementation in a Crystal Oscillator (6 Marks)

    • Circuit Topology: An operational amplifier is configured as a non-inverting amplifier with negative feedback setting the closed-loop gain, while the quartz crystal is connected directly in the series feedback branch to the non-inverting terminal.

    • Operating Mechanism: At series resonant frequency fsf_s, the crystal impedance drops to its minimum equivalent series resistance (RR). The positive feedback loop experiences maximum voltage transfer with exactly zero phase shift, fulfilling the Barkhausen criterion exclusively at fsf_s. Clamping diodes across the feedback resistor provide automatic gain control to maintain unclipped sinusoidal oscillations.


3. Module 3: Power Amplifiers
Unit 1: Power Amplifier Fundamentals (10 Marks Each)
  1. Power Amplifiers Definition and Classification (10 Marks)

    • Definition: Large-signal amplifiers designed primarily to deliver substantial electrical power directly to a load (such as a loudspeaker, transmission antenna, or motor winding) with high conversion efficiency and minimal non-linear distortion.

    • Classification Based on Conduction Angle:

      • Class A: The active device conducts for the full input cycle (θ=360∘\theta = 360^\circ). The operating point is centered on the active load line. Delivers lowest signal distortion but poor maximum conversion efficiency (25%25\% series-fed, 50%50\% transformer-coupled).

      • Class B: Biased at cutoff (ICQ=0I_{CQ} = 0), conducting for exactly one half-cycle (θ=180∘\theta = 180^\circ). Operates in push-pull pairs, achieving up to 78.5%78.5\% efficiency, but exhibits crossover distortion.

      • Class AB: Biased slightly above cutoff with conduction angle 180∘<θ<360∘180^\circ < \theta < 360^\circ. Eliminates crossover distortion while delivering conversion efficiency between 50%50\% and 78.5%78.5\%.

      • Class C: Biased beyond cutoff with conduction angle θ<180∘\theta < 180^\circ (typically 120∘120^\circ to 150∘150^\circ). Uses a tuned LC tank load to recover sinusoidal output; delivers high efficiency (>85%> 85\%) in RF transmitters.

      • Class D: Switches transistors between completely ON (zero voltage) and completely OFF (zero current) using high-frequency pulse-width modulation (PWM). Theoretical conversion efficiency approaches 100%100\%.

  2. Working Operation of Series-Fed Class A Power Amplifier (10 Marks)

    • Circuit Arrangement: A power BJT is connected in series with collector load resistor RCR_C and DC supply voltage VCCV_{CC}. Input is coupled through a base capacitor, and output is drawn from the collector.

    • Biasing and Load Line: Biased in the center of the DC load line:
      VCEQ=VCC2,ICQ=VCC2RCV_{CEQ} = \frac{V_{CC}}{2}, \quad I_{CQ} = \frac{V_{CC}}{2R_C}

    • DC Input Power (Pi(dc)P_{i(\text{dc})}):
      Pi(dc)=VCCICQ=VCC(VCC2RC)=VCC22RCP_{i(\text{dc})} = V_{CC} I_{CQ} = V_{CC}\left(\frac{V_{CC}}{2R_C}\right) = \frac{V_{CC}^2}{2R_C}

    • AC Output Power (Po(ac)P_{o(\text{ac})}):
           For maximum symmetrical peak swing (Vp=VCC2,Ip=VCC2RCV_p = \frac{V_{CC}}{2}, I_p = \frac{V_{CC}}{2R_C}):
      Po(ac,max⁡)=VpIp2=(VCC2)(VCC2RC)2=VCC28RCP_{o(\text{ac},\max)} = \frac{V_p I_p}{2} = \frac{\left(\frac{V_{CC}}{2}\right)\left(\frac{V_{CC}}{2R_C}\right)}{2} = \frac{V_{CC}^2}{8R_C}

    • Conversion Efficiency (\eta):
      η=Po(ac,max⁡)Pi(dc)×100%=VCC28RCVCC22RC×100%=25%\eta = \frac{P_{o(\text{ac},\max)}}{P_{i(\text{dc})}} \times 100\% = \frac{\frac{V_{CC}^2}{8R_C}}{\frac{V_{CC}^2}{2R_C}} \times 100\% = 25\%

    • Transistor Power Dissipation (PDP_D):
           Power dissipated as heat within the transistor is:
      PD=Pi(dc)−Po(ac)P_D = P_{i(\text{dc})} - P_{o(\text{ac})}
           Maximum transistor heating occurs under quiescent conditions with zero input AC signal (PD(max⁡)=Pi(dc)P_{D(\max)} = P_{i(\text{dc})}).