Chapter 5: Tires and Brakes - Key Concepts
Braking Systems: Goals and Basic Concepts
- Primary goal: help slow down the aircraft during the landing roll. Some aircraft also use braking to maneuver on the ground (e.g., differential braking).
- Braking works by converting kinetic energy (motion energy) into heat energy through friction.
- Two main components of a braking system:
- A component that rotates with the wheel (e.g., a drum or a disc).
- A non-rotating component that creates friction to slow the aircraft (e.g., a brake pad or shoe).
- Two main wheel brake unit types:
- Drum-type: older design; not common on modern aircraft but still found on some older planes. A drum is located inside the rotating wheel; an expandable tube or brake shoe sits inside the drum. When braking is required, the expandable component contacts the inside of the rotating drum, creating friction.
- Disc brakes: most aircraft use hydraulic disc brakes. A disc is connected to the rotating wheel; a non-rotating caliper houses brake pads on either side of the disc. When braking, a piston inside the caliper forces the pads against the disc, creating friction to slow the aircraft. Friction also generates heat.
- Figure references: Fig. 5.1 illustrates a drum-type brake; Fig. 5.2 shows a disc-brake system.
- Materials:
- Smaller aircraft: steel discs are common.
- Larger/high-performance aircraft: carbon discs are used to perform better at high braking temperatures; multiple disc units per wheel may be used on larger aircraft to improve braking performance.
- Hydraulics: braking is typically hydraulic even on small aircraft (applied to disc brakes).
Independent Hydraulic Braking (Small Aircraft)
- Most small aircraft use hydraulics to apply pressure to the rotating disc.
- Each brake often has its own self-contained independent hydraulic system (see Fig. 5.3).
- Master cylinder in the pedal acts as the hydraulic pump; pushing the brake pedal pressurizes the hydraulic fluid.
- Hydraulic pressure is transmitted to the braking cylinder via tubing; the pressure is proportional to the force applied on the brake pedal.
- Park brake is incorporated into the system and can hold the pressure on the piston when engaged.
Boosted and Power Braking
- Boosted braking system (for extra help):
- Similar to the independent hydraulic system but can add extra hydraulic pressure during heavy braking.
- Extra pressure is usually provided by the aircraft’s main hydraulic system.
- When brakes are released, the extra pressure is returned to the main hydraulic system.
- Power braking system (for larger/heavier aircraft):
- All braking pressure is provided by the main hydraulic system.
- Brake pedals connect to a control valve that delivers hydraulic pressure to the brake unit on the wheel, proportional to the force applied on the pedal.
Anti-Skid Unit
- Purpose: prevent wheel lock-up on landing (which can cause skidding and dramatically increase landing distance and tire damage).
- Operation: the anti-skid unit compares the speed of the aircraft with the speed of each rotating wheel.
- Speed sensing:
- One method uses a small generator; the output is proportional to the wheel’s rotational speed.
- If the wheel is rotating too slowly relative to the aircraft’s speed, the anti-skid unit momentarily releases hydraulic pressure to the wheel’s braking unit, allowing the wheel to speed up and preventing a skid.
Wheels and Tires: Roles and Distinctions
- Wheel vs tire:
- Wheel: metal component connected to the undercarriage.
- Tire: rubber component, and the only part that contacts the ground.
- Wheel count:
- Small aircraft: often one wheel (and tire) per undercarriage leg.
- Larger aircraft: multiple wheels to spread weight and protect runways/taxiways (tire footprint).
- Wheel materials:
- Aluminum alloy is common.
- Magnesium is lightweight and strong but not typically used on larger aircraft due to fire risk at high braking temperatures.
- Wheel construction:
- Often two-piece construction (two pieces fastened together after tire installation) to withstand greater loads, especially on landing.
Tires: Tubed vs Tubeless; Safety Features
- Tire construction:
- Tubed tires: outer rubber with an inflatable inner tube.
- Tubeless tires: outer rubber seals against the wheel without an inner tube.
- Safety feature: thermal plug
- If braking generates excessive heat, the thermal plug may melt at a pre-set temperature, deflating the tire to reduce the risk of a blowout.
- Preflight inspection importance:
- Pilots check creep marks on tubed tires during preflight.
- Creep: the tire rotating around the rim during touchdown when the tire rotates fast while still stationary with respect to the wheel—this can compromise the inflation valve of the inner tube and lead to deflation.
Tire Condition and Aquaplaning (Hydroplaning)
- Tire tread and wear:
- The tread is the rubber portion that contacts the surface and has a pattern designed to improve braking and ground maneuverability.
- Incorrect inflation leads to uneven tread wear and can compromise tire structure.
- Aquaplaning risk:
- Insufficient tread depth or wear can reduce water evacuation from under the tire, increasing the risk of aquaplaning on wet runways.
- Aquaplaning occurs when a water film sits under the tire, causing a loss of friction and a slide across the water rather than across the runway.
- Case study: aquaplaning on a wet runway
- On 23 September 1999, a Boeing 747 was on a Sydney–Bangkok flight.
- Weather deteriorated with heavy rain; near touchdown, rain intensified; visibility reduced.
- Approximately 10 feet above the runway, the captain called for a go-around; the first officer increased power.
- Simultaneously, main wheels touched the runway, prompting the captain to cancel the go-around and reduce thrust.
- The aircraft was about one-third down the runway and traveling faster than normal due to the thrust increase.
- Because of the heavy water on the runway and the aircraft’s speed, the tires aquaplaned, limiting braking action to about one-third of normal.
- The aircraft overran the runway at 88 knots (≈ 101 mph) and stopped in boggy grass beyond the runway; all occupants evacuated safely.
- This incident highlights how water on the runway can dramatically reduce braking effectiveness and increase stopping distance.
Tire and Wheel Design Details (Key Takeaways)
- The wheel-tire assembly is designed to handle high loads during landing and braking.
- Carbon discs in high-performance aircraft help manage heat during heavy braking.
- Multiple discs on larger aircraft help distribute braking loads and maintain control during the landing roll.
- Independent hydraulic braking systems are common on small aircraft; larger aircraft may use boosted or power braking systems to provide additional hydraulic pressure when required.
- Anti-skid systems are a critical safety feature for preventing tire lock-up and maintaining steerability and braking effectiveness on landing and rollout.
Practical and Safety Implications
- Preflight checks of tires (creep, tread depth, inflation) are essential for safe operations, particularly in adverse weather.
- Runway conditions (wet or contaminated surfaces) require careful management of landing speed, braking, and usage of anti-skid systems to minimize the risk of aquaplaning and overruns.
- Design choices (disc vs drum brakes, material choices, and hydraulic configurations) reflect trade-offs between weight, heat tolerance, reliability, and maintenance implications for different aircraft types.
- Training and procedures emphasize understanding when to deploy boosted or power braking, and how anti-skid systems interact with pilot input during its operation.
Connection to Powerplants and Ground Operations
The tires and braking systems are integral to safe ground operations and interact with powerplant management during landing and rollout (e.g., during a go-around, thrust changes can affect braking performance).
The transition to discussing powerplants and supporting systems in subsequent material will build on this understanding of braking interactions and energy dissipation on the ground.
Key equations and numerical notes:
- Hydraulic pressure relationship to pedal force:
- Anti-skid speed sensing: the sensor output is proportional to wheel speed, e.g.
- Aquaplaning case study reference:
- Braking action in the aquaplaning case: limited to about one-third of normal braking action (\text{factor} \approx \tfrac{1}{3}).