AI free study guide flash cards notes
Flashcards for Inspector Study Guide
Electrical
Q: What is the required clearance for service drops over walkways, patios, or the ground?
A: 10 feet.
Q: How high must service drops be above swimming pools?
A: 22 ½ feet.
Term: Drip loop for overhead triplex.
Definition: A loop in service wires to prevent water from entering the service head.
Q: What wire gauge is used for a 200-amp copper service entrance?
A: 2/0 AWG.
Q: What is a critical inspection step for sub-panels?
A: Ensure there are 4 wires and grounds and neutrals are not connected.
Q: Where are GFCIs required?
A: Bathrooms, kitchens, garages, outdoors, and unfinished basements.
Term: Federal Pacific Electric (FPE) “Stab-lok” breakers.
Definition: Known for safety issues and usually identified by red writing on the breaker tab.
Roofing
Q: What materials are used for roofs with less than a 2:12 slope?
A: Membrane or built-up type materials.
Term: Cedar shakes.
Definition: Requires a minimum slope of 4:12.
Q: What is a safety precaution for specialty roofs?
A: Do not walk on wood, metal, slate, cedar, clay, or other specialty roofs.
Q: What should be inspected around roof flashing?
A: Ensure flashing is properly sealed and free of corrosion.
Exterior
Q: What is the maximum opening for a perimeter railing?
A: 4 inches.
Q: How high should perimeter railings be for decks higher than 30 inches?
A: At least 36 inches.
Term: Weep holes.
Definition: Should be spaced 32 inches apart for brick veneer siding.
Q: What is the minimum height for siding above the ground?
A: 6 inches.
Interior
Q: What is the maximum height of a garage electric eye?
A: No more than 4 inches.
Q: What are the requirements for stair riser height and difference?
A: Risers should be 7” to 8”, with less than a 3/8” difference.
Term: Safety glass requirements.
Definition: Required within 24 inches of doors, 60 inches above floors, and near tubs or showers.
Q: What is the minimum tread depth for stairs?
A: 9 inches.
Plumbing
Q: What is the required drain size for a kitchen sink?
A: 1 ½ inches.
Term: Polybutylene (PB) piping.
Definition: A type of grey piping known for its high failure rate.
Q: What is the minimum clearance for plumbing vents from operable windows?
A: 10 feet away and at least 2 feet above.
Q: What is the maximum length for a straight dryer vent pipe?
A: 35 feet, subtracting 5 feet for each 90-degree elbow.
Q: What safety feature must be installed with water heaters in garages?
A: A bollard to protect against vehicle damage.
Q: What are venting requirements for water heaters?
A: Vents must terminate at least 1 foot above the roof and 10 feet away from operable windows.
Term: Dielectric union.
Definition: A fitting used to connect different metal pipes, preventing corrosion but also breaking the electrical ground.
Q: Why is material compatibility important in plumbing?
A: To prevent galvanic corrosion when connecting dissimilar metals (e.g., copper to galvanized steel).
Q: What is the minimum height for water heater relief valves?
A: Relief valves must be piped down to within 6 inches of the floor to prevent injury from hot water discharge.
Q: What is the required drain size for a kitchen sink?
A: 1 ½ inches.
Term: Polybutylene (PB) piping.
Definition: A type of grey piping known for its high failure rate.
Q: What is the minimum clearance for plumbing vents from operable windows?
A: 10 feet away and at least 2 feet above.
Q: What is the maximum length for a straight dryer vent pipe?
A: 35 feet, subtracting 5 feet for each 90-degree elbow.
Q: What safety feature must be installed with water heaters in garages?
A: A bollard to protect against vehicle damage.
HVAC/Heat Pump
Q: What is the minimum clearance required on the side of a condenser?
A: 12 inches.
Q: What is the normal operating pressure for a steam boiler?
A: 1/2 to 2 psi.
Term: Tridicator.
Definition: A gauge showing pressure and temperature, often found on circulated boilers.
Q: What is the operating temperature range for circulated boilers?
A: 140°F to 160°F.
Q: What is the recommended insulation for suction lines?
A: They should be insulated to prevent condensation and maintain efficiency.
Q: What should be checked during thermostat inspections?
A: Ensure proper wiring connections, secure mounting, and accurate temperature calibration.
Q: What should be inspected in ductwork?
A: Look for leaks, proper insulation, and cleanliness to maintain airflow and energy efficiency.
Q: What are tips for improving HVAC energy efficiency?
A: Regularly replace filters, seal duct leaks, and use programmable thermostats.
Q: What is the minimum clearance required on the side of a condenser?
A: 12 inches.
Q: What is the normal operating pressure for a steam boiler?
A: 1/2 to 2 psi.
Term: Tridicator.
Definition: A gauge showing pressure and temperature, often found on circulated boilers.
Q: What is the operating temperature range for circulated boilers?
A: 140°F to 160°F.
Q: What is the recommended insulation for suction lines?
A: They should be insulated to prevent condensation and maintain efficiency.
Safety
Q: What are the fireplace clearance requirements for combustible materials?
A: 6 inches for materials up to 1.5 inches thick; 12 inches for materials over 1.5 inches thick.
Term: Hearth depth.
Definition: Less than 6 ft² requires 16” depth and 8” on the sides; greater than 6 ft² requires 20” depth and 12” on the sides.
Q: Can different fuel types be mixed in the same chimney?
A: No, only the same fuels can be mixed.
Q: Where should smoke detectors be installed?
A: Inside and outside each bedroom and on every level of the home.
Q: Where should carbon monoxide detectors be installed?
A: Outside sleeping areas and on every level of the home.
Q: What should you check during general household safety inspections?
A: Ensure proper installation of smoke and CO detectors, inspect for tripping hazards, and verify that escape routes are clear.
Term: Carbon monoxide detector.
Definition: A device that alerts occupants to the presence of harmful CO gas, which is odorless and potentially lethal.
Q: What are the fireplace clearance requirements for combustible materials?
A: 6 inches for materials up to 1.5 inches thick; 12 inches for materials over 1.5 inches thick.
Term: Hearth depth.
Definition: Less than 6 ft² requires 16” depth and 8” on the sides; greater than 6 ft² requires 20” depth and 12” on the sides.
Q: Can different fuel types be mixed in the same chimney?
A: No, only the same fuels can be mixed.
Q: Where should smoke detectors be installed?
A: Inside and outside each bedroom and on every level of the home.
These flashcards are based on key topics from the "Inspector Study Guide." Let me know if you'd like adjustments or additional focus on certain sections!