Study Notes on Pectin-Poly(Ethylene Glycol) Methacrylate Hydrogels.

Polymers Article

Authors and Affiliations

  • Authors: Siew Yin Chan, Wee Sim Choo, David James Young, and Xian Jun Loh

  • Affiliations:

    • School of Science, Monash University Malaysia, Subang Jaya 47500, Malaysia

    • Institute of Materials Research and Engineering (IMRE), A*STAR, Singapore 138634, Singapore

    • Faculty of Science, Health, Education and Engineering, University of the Sunshine Coast, Sunshine Coast, QLD 4558, Australia

    • Department of Materials Science and Engineering, National University of Singapore, Singapore 117576, Singapore

    • Singapore Eye Research Institute, Singapore 168751, Singapore

Correspondence Information

  • Emails:

    • choo.wee.sim@monash.edu (W.S.C.)

    • dyoung1@usc.edu.au (D.J.Y.)

    • lohxj@imre.a-star.edu.sg (X.J.L.)

  • Telephone Numbers:

    • +60-3-5514-6114 (W.S.C.)

    • +61-7-5456-3448 (D.J.Y.)

    • +65-6416-8932 (X.J.L.)

Academic Editor

  • Alexander Böker

Submission and Publication Details
  • Received: 2 October 2016

  • Accepted: 10 November 2016

  • Published: 18 November 2016

Abstract

  • Pectin: An anionic, water-soluble polymer comprised of 1,4-linked α-D-galacturonic acid units, used in various applications due to its safe, biodegradable, and renewable characteristics, although it struggles with solubility in organic solvents, making traditional polymerization difficult.

  • Novel Approach: Utilization of cerium-initiated radical polymerization to graft methoxy-poly(ethylene glycol) methacrylate (mPEGMA) onto pectin in aqueous solutions.

  • Characterization: The resultant copolymers were characterized via 1H NMR, FTIR spectroscopy, and TGA and used to create thixotropic supramolecular hydrogels with the addition of α-cyclodextrin (α-CD) to induce cross-linking.

  • Properties: The hydrogels demonstrated unique rheological properties, maintaining gel consistency irrespective of temperature variations, in contrast to standard poly(ethylene glycol) (PEG)-grafted hydrogels.

Keywords

  • Pectin, poly(ethylene glycol) methacrylate, cerium, α-cyclodextrin, supramolecular hydrogel

1. Introduction

  • Pectins: Complex carbohydrates from dicotyledonous and some monocotyledonous plants.

  • Source: Extracted from food industry waste, notably citrus peel and apple pomace using hot dilute mineral acid.

  • Safety and Applications: Recognized as a non-toxic food additive with applications in food, pharmaceuticals, and cosmetics; serves as emulsifiers, gelling agents, stabilizers, or thickeners.

Structure and Classification

  • Chemical Structure: Composed of galacturonic acid units joined by α-(1→4) glycosidic bonds.

  • Degree of Methylation (DM): Defined as the molar ratio of methyl esters relative to total GalA units.

    • Classification:

    • High Methoxy Pectin (HMP): DM > 50%

    • Low Methoxy Pectin (LMP): DM < 50%

Mechanism of Gelation

  • HMP: Gels formed through hydrophobic forces and hydrogen bonding in high co-solute concentrations.

  • LMP: Gels in the presence of divalent cations like calcium through ionic cross-linking (Egg-box model).

2. Materials and Methods

2.1. Synthesis of Pectin-PEGMA Copolymer (P-10K)

  • Reagents: Ammonium cerium (IV) sulfate dihydrate, apple pectin, mPEGMA, α-cyclodextrin.

  • Synthesis Process:

    1. Add ammonium cerium(IV) sulfate to 1% w/v pectin solution, stir for 2 hrs.

    2. Introduce mPEGMA into the reaction mixture and stir for 48 hrs.

    3. Post-synthesis, add chloroform for extraction; three distinct layers form upon settling: cloudy solution, white emulsion, and transparent chloroform layer.

    4. Pectin-PEGMA was precipitated from the white emulsion with hexane, yielding a 61.5% yield, dried under vacuum at 40°C.

2.2. Polymer Characterization

  • 1H NMR Spectroscopy: Conducted using a JEOL 500 MHz spectrometer; spectral shifts referenced against deuterium oxide solvent.

  • FTIR Spectroscopy: Using a Perkin Elmer Spectrum 2000 spectrometer; KBr pellets prepared for analysis. Key spectral features included:

    • Broad peak at 3450 cm⁻¹ (O–H stretching for pectin), peaks at 1750 and 1630 cm⁻¹ (C=O stretches).

2.3. Thermal Analysis

  • TGA: Performed with a TA Instruments Q500 model; samples heated to 900°C under nitrogen at a rate of 20°C/min.

2.4. Preparation of Pectin-PEGMA/α-CD Hydrogels

  • Hydrogel Formation: Solutions of α-CD mixed with pectin-PEGMA of varying concentrations, sonicated, allowed to gel after 24 hrs.

    • Critical Gelation Concentration: Evaluated by plotting α-CD vs. polymer concentration (1%–10% w/v).

2.5. Rheology Studies

  • Rheometer: Utilized a Discovery DHR-3 instrument; tests conducted at specified strain rates (0.01%–100%) and temperatures (25°C and 37°C).

  • Amplitude Sweeps: Collected in the linear viscoelastic region (LVR); frequency sweeps performed to analyze the impact of oscillation frequency.

3. Results

3.1. Synthesis and Characterization of Pectin-PEGMA Copolymer

  • Yield and Composition: Confirmed presence of pectin in the P-10K with TGA analysis indicating approximately 17% by weight.

  • FTIR Findings: Supported the graft presence of pectin in the copolymer, highlighting both contributions from pectin and mPEGMA.

3.2. Thermal Analysis Results

  • Decomposition Temperatures: Recorded for precursors—pectin exhibited 86.33°C and 253.33°C; 10KPEGMA showed 418.07°C, while P-10K revealed combined degradation temperatures reflective of its constituent polymers.

3.3. Critical Gelation Concentration Determination

  • Gel Formation: Observed with α-CD at a minimum polymer concentration (1% w/v) needed to achieve gelation.

3.4. Rheological Properties of Pectin-PEGMA/α-CD Hydrogel

  • Shear Strain Response: Demonstrated typical gel-to-liquid transition beyond critical strain (7% - 11%); confirmed by amplitude and frequency sweeps.

3.5. Thixotropic Properties

  • Thixotropy Validation: Amplitude sweeps confirmed that gel structures recovered post-shear, indicating thixotropic behavior of the hydrogel, which reverted to gel consistency after rest.

3.6. Temperature Effects on Hydrogels

  • Temperature Analysis: Hydrogel maintained properties in the 10°C–40°C range, showing consistent G’ and G” values, demonstrating thermal stability compared to conventional PEG-grafted hydrogels.

4. Discussion

  • Synthesis Validation: Successful creation of pectin-PEGMA noted through distinct analytical methods with evidence of thermal stability.

  • Copolymer Gelling Mechanism: Gels formed via α-CD threading onto PEG chains, initiating aggregation.

  • Thixotropic Nature: The copolymer demonstrates favorable processing characteristics for industrial applications, maintaining form under temperature fluctuations while remaining responsive to shear forces.

Conclusion

  • Pectin-PEGMA (P-10K) copolymer demonstrates eco-friendly synthesis via cerium-initiated polymerization in water, facilitating low-concentration gel formation at room temperature.

  • Ideal for potential applications across cosmetics and pharmaceuticals, with ongoing evaluations for biocompatibility and biodegradability.

Acknowledgments

  • Funding received from Monash University Malaysia and A*STAR’s IMRE, with thanks to contributors for illustrations.