Comprehensive Study Guide: Wheelchair Mechanics, Types, and Fitting
Introduction to Wheelchair Mobility and Terminology
- Terminology of Locomotion: The act of movement via a wheelchair is formally referred to as propelling or propulsion, as opposed to "ambulation" which refers specifically to walking.
- Wheelchair Selection and Fitting: The primary lab and competence task for clinicians involves measuring a wheelchair to ensure a proper fit for a standard model and teaching patients how to navigate their environment effectively.
Classification and Characteristics of Wheelchairs
- Standard Adult Wheelchair: Designed for basic utility and foldable for storage. The general weight threshold for a standard chair is approximately . If a patient exceeds this, comfort and pressure points must be carefully assessed.
- Bariatric Wheelchair: Heavy-duty chairs designed for patients with high Body Mass Indices (BMI), extreme height, or weight over a certain threshold (typically recommended if the patient is or more). These are wider to accommodate adipose tissue, particularly in the lower extremities.
- Ultralight Wheelchair: Commonly utilized for patients with spinal cord injuries.
- Construction: Often made from lightweight titanium.
- Design Features: Smaller frames, absence of back handles (to encourage independence), and lack of armrests to facilitate easier transfers. The wheels are often canted for better propulsion.
- Portability: These are easily collapsible and designed for rapid disassembly/reassembly (e.g., removing wheels) to allow the user to place the chair in a vehicle independently.
- Child/Intermediate Wheelchair: Sized specifically for pediatric patients and intended as temporary equipment as the child grows.
- Hemiplegic (Hemi-height) Wheelchair: Designed for patients following a stroke (hemiplegia) who can only propel with one side of their body.
- Seat Height: The seat is lowered to from the ground. This allows the patient to use their unaffected lower extremity to pull or push the chair along the floor.
- Back Support: The backrest is relatively taller to compensate for the lower seat height and provide better trunk support for those with limited core control.
- Amputee Wheelchair: Features specialized attachments called a trough to support a residual limb and keep it slightly elevated. This prevents the limb from dangling in a flexed position. The center of gravity is often adjusted to prevent the chair from tipping backward due to the missing limb weight.
- One-handed Drive Wheelchair: Features two handrims on a single side connected by a specialized axle.
- Operation: The patient can push both rims simultaneously to go straight. Pushing only the inside rim allows for turning.
- Externally Powered (Electric) Wheelchairs: Driven by motors rather than skeletal muscle. These are necessary for patients with high cervical spinal cord injuries who lack upper extremity function.
- Control Mechanisms: Can be operated via joystick (for fine motor control), chin units (utilizing cervical protraction/retraction), or sip-and-puff systems (respiratory breath control).
- Weight Warning: These units are extremely heavy and can cause injury to clinicians if they run over feet.
- Reclining and Tilt-in-Space Wheelchairs:
- Manual Reclining: Features levers that allow a caregiver to recline the backrest to offload pressure.
- Power Tilt-in-Space: An electric system where the entire seat and back unit tilts together, preserving the hip angle while shifting weight for pressure relief.
- Transport Wheelchair: Designed exclusively for short-term transportation (e.g., moving a patient from a room to a car).
- Features: Characterized by four small wheels. It is not safe for long-term sitting or independent propulsion.
- Safety Risk: These lack the stability of a large wheelbase and can tip easily if the patient leans forward or backward. They are never to be used as a primary mobility device.
- Sports Specific Wheelchairs: Highly customized chairs (e.g., for basketball) with significantly canted wheels for rapid maneuvering and minimal trunk support.
Anatomical and Mechanical Considerations of Wheelchair Parts
- Cushions and Pressure Relief:
- Rojo (Roho) Cushion: A brand of pressure relief cushion consisting of individual air-filled pockets. It mimics the feel of a waterbed and helps distributive pressure away from bony prominences.
- Opening the Wheelchair: To open a standard chair, one should push down on the inside edges of the seat rails until it clicks into place. Do not attempt to pull it apart by the armrests.
- Wheel Locks: CRITICAL SAFETY RULE: The wheelchair must ALWAYS be locked before a patient attempts to move into or out of it. It should also remain locked while the patient is stationary.
- Removable Components: Armrests and footrests are often removable or "swing-away" to facilitate transfers. Some wheelchairs have elevating leg rests with pads to support the lower legs.
- Wheels and Rims: Users should propel the chair using the handrims located on the outside of the wheels, rather than touching the tires directly.
Anthropometric Measurements and Fitting Consequences
Proper fitting is essential for preventing secondary injuries and ensuring functional mobility.
- Seat Height:
- Too High: Poor trunk support and difficulty reaching the rims or the floor for propulsion.
- Too Low: Increases pressure on the ischial tuberosities; the backrest may rub against the scapulae.
- Seat Depth:
- Too Short: Inadequate thigh support leading to trunk instability.
- Too Long: Causes pressure injuries in the popliteal space and may impede circulation.
- Seat Width:
- Too Wide: Results in shoulder pain during propulsion, difficulty navigating doorways, and poor postural support.
- Too Narrow: Excessive pressure on the hips and greater trochanters.
- Back Height:
- Too High: Causes skin irritation and pressure on the scapulae.
- Too Low: Results in trunk imbalance and inadequate support.
- Armrest Height:
- Too High: Causes shoulder pain/elevation and difficulty reaching the rims.
- Too Low: Makes sit-to-stand transfers difficult and provides no support for the upper body.
- Footrest Height:
- Too High: Puts the user into "sacral sitting," shifting all weight to the ischial tuberosity and forcing excessive knee flexion.
- Too Low: Impedes clearing thresholds (e.g., bumps/doorways) and puts pressure on the posterior thigh.
Clinical Protocols for Pressure Relief
Pressure relief is required for any patient who is "wheelchair bound" (spending all waking hours in the chair) to prevent pressure injuries.
- The Rule of Two Minutes: Every , a patient must perform a total of of pressure relief.
- Methods:
- Side-to-Side Lean: Lean to one side for , then the other side for . The patient must fully clear the ischial tuberosity from the seat.
- Forward Lean: Lean forward for a total of . (Clinicians often prefer side-leaning for safety/balance).
- Tricep Push-ups: Locking the wheels and using the armrests to lift the body; however, this is physically demanding and difficult for many patients.
Professional Scope and Selection Criteria
- Recommending Equipment: Physical Therapist Assistants (PTAs) are within their scope to recommend wheelchair adaptations (e.g., elevating leg rests, pressure relief cushions) to the PT or orthotist.
- Documentation: Clinicians must provide strong justification for equipment to ensure insurance coverage. This includes assessing the patient's prognosis (temporary vs. permanent need) and their home environment (e.g., apartment floor, elevator access).
- Accessibility Advocacy: Clinicians should be mindful of hatched parking spaces next to handicap spots, as these are essential for wheelchair users to fully open car doors and assemble their ultralight chairs.
Questions & Discussion
- Q: Do all ultralight wheelchairs have an access axle connecting the wheels?
- A: Not always, but many do. Some use a crossbar, but the design depends on the specific level of injury and the patient's functional needs.
- Q: Are the armrests on the standard wheelchair removable?
- A: Yes, most standard wheelchairs have removable armrests to facilitate lateral transfers, though older models may be difficult to detach due to wear.
- Anecdote (The "Roomba" Patient): The instructor described a patient named Rupa who propelled her wheelchair using only her legs. Because she would move, hit an object, and change directions randomly, the staff nicknamed her "Roomba."