104 Ch.8

Ch. 8 X-Ray Unit Circuitry Lecture Notes 10/14/25

Types of Current

Direct Current (DC)
  • Definition: DC is defined as current that flows in only one direction at all times.

  • Production: Produced by capacitors (batteries) and rectifiers (devices that convert AC to DC).

  • Application: Primarily used by x-ray tubes.

Alternating Current (AC)
  • Definition: AC is current that flows in a positive direction for half of the time and in a negative direction for the other half.

  • Production: Generated by generators.

  • Application: Used by transformers in x-ray circuits; transformers require alternating current to function properly.

Basic X-ray Machine Circuit

  • Source of Voltage: The incoming voltage is supplied by the local power plant.

  • Line Voltage Compensator: Ensures consistent voltage delivery to the x-ray tube and circuit.

    • Analogy: Functions similarly to a surge protector, stabilizing the incoming voltage.

Three Circuits Making Up the X-ray Circuit
  1. Primary (Low Voltage) Circuit

  2. Secondary (High Voltage) Circuit

  3. Filament Circuit: Operates at low voltage and high current.

Transformers

Purpose of Transformers
  • To either increase or decrease voltage levels within a circuit.

Basic Components of a Transformer
  1. 1st Coil

  2. 2nd Coil

  3. Ferromagnetic Core

Operation Principles
  • Mutual Induction: Transformers operate based on the principle of mutual induction and require alternating current exclusively.

  • Voltage and Current Relations: The primary voltage and current do not equal the secondary voltage or current unless the number of turns in the coils is equal.

Autotransformer
  • Controls the kilovolt peak (kVp) output of the circuit.

Transformer Law for Voltage and Current

  1. Voltage Relation:

    • Formula: V<em>sV</em>p=N<em>sN</em>p\frac{V<em>s}{V</em>p} = \frac{N<em>s}{N</em>p}

    • Where:

      • VsV_s = Voltage in secondary winding

      • VpV_p = Voltage in primary winding

      • NsN_s = Number of turns in secondary winding

      • NpN_p = Number of turns in primary winding

  2. Current Relation:

    • Formula: I<em>sI</em>p=V<em>pV</em>s\frac{I<em>s}{I</em>p} = \frac{V<em>p}{V</em>s}

    • Important Note: The power output cannot exceed the power input, thus emboldening the importance of the relationship defined by: P=IVP = IV

Types of Transformers

  1. Autotransformer: Can increase or decrease both voltage and amperage.

  2. Step-up Transformer: Provides high-voltage (low current, with fewer electrons) to the tube.

  3. Step-down Transformer: Provides high current (low voltage) to the filament.

    • Necessitated for thermionic emission to occur, allowing electrons to be boiled off.

  4. Mutual Induction: Maximum mutual induction occurs in shell core transformers.

    • Basic components include iron core, primary input, and secondary output.

Primary Circuit

  • Contains the Autotransformer.

  • Requires a substantial amount of electrons in motion.

  • Only consists of the primary coil of a step-up transformer.

  • Controls located on the low voltage side of the circuit.

Rectifiers

Purpose of Rectifiers
  • Designed to convert AC to DC.

Types of Rectifiers
  • Solid State Devices: Allow current flow in only one direction.

  • Circuit Positioning: Rectification occurs post step-up transformer and prior to the x-ray tube within the x-ray circuit.

    • Essential for pulsing the magnetic field from the primary to secondary coil.

Direction of Current and Electrons
  • Current and electrons flow in opposite directions:

    • Electrons Flow: From cathode to anode.

Types of Rectification
  1. Half-wave Rectification: Stops backflow of negative current.

  2. Full-wave Rectification: Converts backflow (negative) to forward flow (positive current).

    • Note: Exact number of rectifiers in a circuit is not necessary to memorize.

Phase Types of Current
  • Single Phase: Can be denoted as 1°.

  • Three Phase, Six Pulse: Denoted as 3°12P.

  • Three Phase, Twelve Pulse: Denoted as 3°12P.

  • Ripple Characteristics: Maximum and minimum ripple values to be monitored to maintain voltage stability.

Rectification and Voltage Ripple

  • The amount of voltage corresponds with variations in x-ray circuits:

    • Single Phase: 1/3% of set kV with a 100% ripple.

    • Three Phase, Six Pulse: 91% of set kV with a 14% ripple.

    • Three Phase, Twelve Pulse: 97% of set kV with a 4% ripple.

    • High-Frequency Generator: 100% of set kV with <1% ripple.

Filament Circuit

  • Necessitates a step-down process to elevate the current, ensuring that electrons are boiled off through thermionic emission.

  • Houses the step-down transformer which decreases voltage while increasing current.

  • Rheostat: A resistor that changes its resistance to allow current flow to decrease.

Control Panel on Low Voltage (Primary) Side
  • kVp and mA selectors: Connected to the autotransformer.

  • Timer: Mechanism to terminate exposure.

    • Types of timing mechanisms include:

    • Synchronous (less precise)

    • Electronic

    • AEC (Automatic Exposure Control)

Automatic Exposure Control (AEC)

Purpose of AEC
  • Ensures correct exposure settings regardless of patient size by controlling the duration of exposure.

  • Tech Technologist Role: Selection of mA and kVp is done by the technologist.

  • Critical Factors: Positioning and centering of the patient is vital for optimal imaging.

Components of AEC
  • Ion Chambers: 3-5 independent chambers positioned between the patient and the image receptor.

  • Backup Timer: Generally set to automatically terminate exposure after 5 seconds to prevent tube overload.

  • Re-calibration Necessity: Required when new image receptors or grids are introduced into the system.

Rectifiers Used in X-ray Circuits (Non-examination Material)

  • Single Phase, Full Wave: 2 or 4 rectifiers.

  • Three Phase, Six Pulse: 6 rectifiers.

  • Three Phase, 12 Pulse: 12 rectifiers.