Engineering Tolerances, Precision Measurement, and Statistical Analysis

Fundamentals of Engineering Tolerances and ANSI/ASME Standards

  • Necessity of Tolerances in Manufacturing:

    • Variation is an unavoidable physical reality in all manufacturing processes.

    • No two manufactured parts are ever completely identical; some degree of dimensional variation will always exist.

    • Tolerances are applied on production drawings to control manufacturing processes and restrict the permissible variation between duplicate copies of the same component.

    • Tolerances applied to mating parts in an assembly ensure interchangeability, allowing components from different production runs or manufacturers to assemble and function properly.

  • Functional and Economic Trade-offs:

    • Specifying a tolerance that is too large can impair or prevent the correct operation and fit of a part within an assembly.

    • Specifying a tolerance that is too small (overly tight) significantly drives up production expenses, requires specialized precision machinery, and increases quality control inspection overhead and part rejection rates.

    • A primary engineering rule is to never specify a tolerance smaller or tighter than necessary for the component to function as intended.

    • In general, dimensions specified with more significant figures (more digits to the right of the decimal point) represent tighter tolerances and higher production costs.

  • ANSI/ASME Standard Y14.5:

    • Mandates that every dimension on a technical drawing must have an associated tolerance, with specific exceptions for dimensions designated as reference, maximum, minimum, or stock sizes.

    • Tolerances may be applied directly to a given dimension or established via a general note located within the title block of the drawing sheet.

  • Core Mathematical Definitions of Limits and Tolerance:

    • Tolerance: The total acceptable amount of dimensional variation that allows an object to function correctly; mathematically defined as the difference between the upper and lower limits:         Tolerance=Upper Limit−Lower Limit\text{Tolerance} = \text{Upper Limit} - \text{Lower Limit}

    • Specified Dimension: The target or nominal dimension from which the allowable limit boundaries are calculated.

    • Limits: The maximum and minimum allowable physical sizes dictated by the toleranced dimension.

    • Upper Limit: The maximum allowable dimension for a feature:         Upper Limit=Specified Dimension+Positive Variance\text{Upper Limit} = \text{Specified Dimension} + \text{Positive Variance}

    • Lower Limit: The minimum allowable dimension for a feature:         Lower Limit=Specified Dimension+Negative Variance\text{Lower Limit} = \text{Specified Dimension} + \text{Negative Variance}

Tolerance Formats and Working Drawing Specifications

Part drawing demonstrating limit dimensions, bilateral tolerance, and unilateral tolerance
  • Primary Tolerance Formats:

    • Limit Dimensions:

      • Explicitly state the upper limit and lower limit directly on the drawing view.

      • Any manufactured size between or equal to the upper limit and lower limit is functionally acceptable.

      • Example (stacked notation):             0.1260.125\begin{matrix} 0.126 \\ 0.125 \end{matrix}             where the upper limit is 0.126 in.0.126\,\text{in.} and the lower limit is 0.125 in.0.125\,\text{in.}

      • Total tolerance calculation for this example:             Tolerance=0.126−0.125=0.001 in.\text{Tolerance} = 0.126 - 0.125 = 0.001\,\text{in.}

    • Bilateral Tolerance:

      • Specifies an allowable variation in both directions (larger and smaller) relative to the specified dimension.

      • Uses a plus/minus symbol (±\pm) when the variation is equal in both directions.

      • Example: A hole center location designated as 1.50±0.05 in.1.50 \pm 0.05\,\text{in.}

        • Specified Dimension = 1.50 in.1.50\,\text{in.}

        • Upper Limit=1.50+0.05=1.55 in.\text{Upper Limit} = 1.50 + 0.05 = 1.55\,\text{in.}

        • Lower Limit=1.50−0.05=1.45 in.\text{Lower Limit} = 1.50 - 0.05 = 1.45\,\text{in.}

        • Tolerance=1.55−1.45=0.10 in.\text{Tolerance} = 1.55 - 1.45 = 0.10\,\text{in.}

      • Example: Counterbore depth specified as ⌞ ⁣⌟ ∅1.25 ↓ˉ 0.250±0.003 in.\llcorner\!\lrcorner\, \varnothing 1.25 \,\bar{\downarrow}\, 0.250 \pm 0.003\,\text{in.}

        • Allowable variation is 0.003 in.0.003\,\text{in.} larger or smaller than the nominal depth of 0.250 in.0.250\,\text{in.}

        • Upper Limit=0.250+0.003=0.253 in.\text{Upper Limit} = 0.250 + 0.003 = 0.253\,\text{in.}

        • Lower Limit=0.250−0.003=0.247 in.\text{Lower Limit} = 0.250 - 0.003 = 0.247\,\text{in.}

        • Tolerance=0.253−0.247=0.006 in.\text{Tolerance} = 0.253 - 0.247 = 0.006\,\text{in.}

    • Unilateral Tolerance:

      • Provides an allowable variation in only one direction (either larger or smaller) from the specified dimension.

      • Denoted using separate plus (+$) and minus (-) signs.\n * Example: A hole feature noted as \varnothing 0.500^{+0.004}{-0.000}\,\text{THRU}\n * The hole diameter may vary up to 0.004\,\text{in.}larger,butcannotbesmallerthanthenominallarger, but cannot be smaller than the nominal0.500\,\text{in.}\n * \text{Upper Limit} = 0.500 + 0.004 = 0.504\,\text{in.}\n * \text{Lower Limit} = 0.500 - 0.000 = 0.500\,\text{in.}\n * \text{Tolerance} = 0.504 - 0.500 = 0.004\,\text{in.}\n\n![Bushing drawing with limit dimensions and bilateral tolerances](https://assets.knowt.com/pdf-flow-prod/48806193-1b89-481f-852c-cd0d858db1bb-figures/0.png)\n\n* **Analysis of Flanged Bushing Dimensions:**\n * **Inner Bushing Diameter:**\n * Marked dimension: \varnothing^{1.005}{1.000}\n * Tolerance Format: Limit dimensions.\n * The inner diameter must be at least 1.000\,\text{in.}butcanbenomorethanbut can be no more than1.005\,\text{in.}\n * Upper limit is 1.005\,\text{in.},andlowerlimitis, and lower limit is1.000\,\text{in.}\n * Total tolerance: 1.005 - 1.000 = 0.005\,\text{in.}\n * **Outer Bushing Diameter:**\n * Marked dimension: \varnothing 1.252 \pm 0.003\n * Tolerance Format: Bilateral tolerance.\n * Specified dimension is 1.252\,\text{in.}\n * The outer diameter may vary by no more than 0.003\,\text{in.}greaterthanorlessthangreater than or less than1.252\,\text{in.}\n * Permissible size range: 1.249\,\text{in.}toto1.255\,\text{in.}\n * \text{Upper Limit} = 1.252 + 0.003 = 1.255\,\text{in.}\n * \text{Lower Limit} = 1.252 - 0.003 = 1.249\,\text{in.}\n * Total tolerance: 1.255 - 1.249 = 0.006\,\text{in.}\n\n![L-shaped part with unilateral tolerances](https://assets.knowt.com/pdf-flow-prod/48806193-1b89-481f-852c-cd0d858db1bb-figures/2.png)\n\n* **Analysis of Machined Bracket Features:**\n * **Contour Radius Feature:**\n * Marked dimension: R15^{+0}{-0.1}\,\text{mm}\n * Tolerance Format: Unilateral tolerance.\n * The contour radius cannot be greater than 15.0\,\text{mm}.\n * The radius can be as small as 14.9\,\text{mm}.\n * All allowable deviation is less than the specified size.\n * \text{Tolerance} = 15.0 - 14.9 = 0.1\,\text{mm}\n * **Base Length Feature:**\n * Marked dimension: 30^{+0}{-0.2}\,\text{mm}\n * Tolerance Format: Unilateral tolerance.\n * \text{Upper Limit} = 30.0\,\text{mm};;\text{Lower Limit} = 29.8\,\text{mm};;\text{Tolerance} = 0.2\,\text{mm}\n * **Slot Width Feature:**\n * Marked dimension: 16^{+0.1}_{-0}\,\text{mm}\n * Tolerance Format: Unilateral tolerance.\n * \text{Upper Limit} = 16.1\,\text{mm};;\text{Lower Limit} = 16.0\,\text{mm};;\text{Tolerance} = 0.1\,\text{mm}\n\n![Working drawing of a plate with counterbored and countersunk holes with title block tolerances](https://assets.knowt.com/pdf-flow-prod/210b7696-dd7a-42ed-9353-67f0e9ed7da5-figures/4.jpg)\n\n* **General Tolerances (Drawing Title Block Defaults):**\n * General tolerances are assumed when no explicit tolerance is tied directly to a specific dimension.\n * Standard title block rules based on decimal places for linear dimensions and angles:\n * One decimal place (X.X):):\pm 0.020\,\text{in.}\n * Two decimal places (X.XX):):\pm 0.010\,\text{in.}\n * Three decimal places (X.XXX):):\pm 0.005\,\text{in.}\n * Angular dimensions: \pm 0.5^\circ\n * **Calculations for Linear Dimensions Governed by General Tolerances:**\n * **Dimension of 3.00\,\text{in.}:**\n * Two decimal places (X.XX)invokes) invokes\pm 0.010\,\text{in.}\n * \text{Upper Limit} = 3.00 + 0.010 = 3.010\,\text{in.}\n * \text{Lower Limit} = 3.00 - 0.010 = 2.990\,\text{in.}\n * \text{Tolerance} = 3.010 - 2.990 = 0.020\,\text{in.}\n * **Dimension of 2.000\,\text{in.}:**\n * Three decimal places (X.XXX)invokes) invokes\pm 0.005\,\text{in.}\n * \text{Upper Limit} = 2.000 + 0.005 = 2.005\,\text{in.}\n * \text{Lower Limit} = 2.000 - 0.005 = 1.995\,\text{in.}\n * \text{Tolerance} = 2.005 - 1.995 = 0.010\,\text{in.}\n * **Dimension of 0.5\,\text{in.}:**\n * One decimal place (X.X)invokes) invokes\pm 0.020\,\text{in.}\n * \text{Upper Limit} = 0.5 + 0.020 = 0.520\,\text{in.}\n * \text{Lower Limit} = 0.5 - 0.020 = 0.480\,\text{in.}\n * \text{Tolerance} = 0.520 - 0.480 = 0.040\,\text{in.}\n * **Dimension of 1.001\,\text{in.}:**\n * Three decimal places (X.XXX)invokes) invokes\pm 0.005\,\text{in.}\n * \text{Upper Limit} = 1.001 + 0.005 = 1.006\,\text{in.}\n * \text{Lower Limit} = 1.001 - 0.005 = 0.996\,\text{in.}\n * \text{Tolerance} = 1.006 - 0.996 = 0.010\,\text{in.}\n * **Dimension of 4.50\,\text{in.}:**\n * Two decimal places (X.XX)invokes) invokes\pm 0.010\,\text{in.}\n * \text{Upper Limit} = 4.50 + 0.010 = 4.510\,\text{in.}\n * \text{Lower Limit} = 4.50 - 0.010 = 4.490\,\text{in.}\n * \text{Tolerance} = 4.510 - 4.490 = 0.020\,\text{in.}\n\n* **Evaluations of Bilateral Tolerances:**\n * 1.60 \pm 0.05:\n        \text{Upper Limit} = 1.65, \quad \text{Lower Limit} = 1.55, \quad \text{Tolerance} = 1.65 - 1.55 = 0.10\n * 0.5 \pm 0.2:\n        \text{Upper Limit} = 0.7, \quad \text{Lower Limit} = 0.3, \quad \text{Tolerance} = 0.7 - 0.3 = 0.4\n * 3.605 \pm 0.002:\n        \text{Upper Limit} = 3.607, \quad \text{Lower Limit} = 3.603, \quad \text{Tolerance} = 3.607 - 3.603 = 0.004\n * 4.001 \pm 0.005:\n        \text{Upper Limit} = 4.006, \quad \text{Lower Limit} = 3.996, \quad \text{Tolerance} = 4.006 - 3.996 = 0.010\n\n* **Component Compliance Case Study (2.50 \pm 0.02\,\text{in.}):**\n * Specified Dimension: 2.50\,\text{in.}withbilateraltolerancewith bilateral tolerance\pm 0.02\,\text{in.}\n * \text{Upper Limit} = 2.50 + 0.02 = 2.52\,\text{in.}\n * \text{Lower Limit} = 2.50 - 0.02 = 2.48\,\text{in.}\n * \text{Total Tolerance} = 2.52 - 2.48 = 0.04\,\text{in.}\n * *Evaluation of 2.515\,\text{in.}:∗Acceptable,because:* Acceptable, because2.48\,\text{in.} \le 2.515\,\text{in.} \le 2.52\,\text{in.}\n * *Evaluation of 2.53\,\text{in.}:∗Unacceptable(rejectedasoutoftolerance),because:* Unacceptable (rejected as out of tolerance), because2.53\,\text{in.} > 2.52\,\text{in.} (exceeds the upper limit).\n\n\n# Mating Parts, Material Conditions, and Types of Fit\n\n* **Classifications of Fit Between Mating Parts:**\n * **Clearance Fit:** Limits the size of mating parts such that a clearance (gap) always results when the mating parts are assembled throughout their entire tolerance ranges.\n * **Interference Fit:** Limits the size of mating parts such that an interference always results upon assembly, requiring force or thermal expansion/contraction to press together.\n * **Transition Fit:** Occurs when the calculated limits of mating parts overlap, such that the assembly can result in either a clearance fit or an interference fit depending on the actual manufactured dimensions of the individual parts.\n\n* **Material Condition Principles:**\n * **Maximum Material Condition (MMC):** The condition of a part feature when it contains the maximum amount of material within its stated limits:\n * For an *external feature* (such as a shaft, pin, axle, or overall plate thickness), MMC corresponds to the **upper limit** of the dimension (the largest permissible external size).\n * For an *internal feature* (such as a hole, bore, or slot), MMC corresponds to the **lower limit** of the dimension (the smallest permissible hole diameter, leaving the most material in the part).\n * **Least Material Condition (LMC):** The condition of a part feature when it contains the minimum amount of material within its stated limits:\n * For an *external feature*, LMC corresponds to the **lower limit** of the dimension (the smallest permissible external size).\n * For an *internal feature*, LMC corresponds to the **upper limit** of the dimension (the largest permissible hole diameter, removing the most material from the part).\n\n* **Allowance Definition and Calculation:**\n * **Allowance:** The intentional difference between the maximum material limits of mating parts. It represents the tightest possible fit: the minimum clearance or maximum interference.\n * Fundamental Equation:\n        \text{Allowance} = \text{MMC internal feature} - \text{MMC external feature}\n * A positive allowance indicates a clearance condition at MMC (tightest clearance).\n * A negative allowance indicates an interference condition at MMC (maximum interference).\n\n![Mating axle and opening illustrating a clearance fit](https://assets.knowt.com/pdf-flow-prod/48806193-1b89-481f-852c-cd0d858db1bb-figures/6.jpg)\n\n* **Worked Example 1: Clearance Fit Assembly:**\n * Axle (External Feature) Limits: \begin{matrix} 10.00 \ 9.92 \end{matrix}\n * Axle MMC = 10.00 (upper limit, largest shaft)\n * Axle LMC = 9.92 (lower limit, smallest shaft)\n * Hole Opening (Internal Feature) Limits: \begin{matrix} 10.25 \ 10.15 \end{matrix}\n * Hole MMC = 10.15 (lower limit, smallest hole)\n * Hole LMC = 10.25 (upper limit, largest hole)\n * Allowance Calculation:\n        \text{Allowance} = \text{MMC internal feature} - \text{MMC external feature} = 10.15 - 10.00 = 0.15\n * Because the minimum hole size (10.15)isstrictlylargerthanthemaximumshaftsize() is strictly larger than the maximum shaft size (10.00),aclearancealwaysresults(minimumclearance=), a clearance always results (minimum clearance =0.15,maximumclearance=, maximum clearance =10.25 - 9.92 = 0.33). This is a **Clearance Fit**.\n\n![Mating axle and opening illustrating an interference fit](https://assets.knowt.com/pdf-flow-prod/48806193-1b89-481f-852c-cd0d858db1bb-figures/5.png)\n\n* **Worked Example 2: Interference Fit Assembly:**\n * Axle (External Feature) Limits: \begin{matrix} 10.00 \ 9.92 \end{matrix}\n * Axle MMC = 10.00\n * Axle LMC = 9.92\n * Hole Opening (Internal Feature) Limits: \begin{matrix} 9.90 \ 9.85 \end{matrix}\n * Hole MMC = 9.85\n * Hole LMC = 9.90\n * Allowance Calculation:\n        \text{Allowance} = \text{MMC internal feature} - \text{MMC external feature} = 9.85 - 10.00 = -0.15\n * Because the largest hole size (9.90)isstrictlysmallerthanthesmallestaxlesize() is strictly smaller than the smallest axle size (9.92),aninterferencealwaysresults(maximuminterference=), an interference always results (maximum interference =0.15,minimuminterference=, minimum interference =9.92 - 9.90 = 0.02). This is an **Interference Fit**.\n\n* **Out of Tolerance Definition and Quality Control:**\n * A part is designated as *out of tolerance* whenever its physical measured dimensions fall outside the upper or lower limits specified by the drawing.\n * Manufacturing plants implement formal quality control inspection procedures to detect, reject, and prevent out-of-tolerance parts from entering assembly lines or shipping to customers.\n\n\n# Technical Drawing Conventions and Precision Measurement\n\n* **Section Views and Associated Symbology:**\n * **Section View:** A drafting view used to reveal internal ("inside") geometrical details, contours, and cavities that are not apparent from the exterior surfaces of the part.\n * **Cutting Plane Line:** A thick, prominent line drawn on an orthographic view indicating the precise path where an imaginary cut has been made through the object to establish the section plane.\n * **Section Lines (Hatching):** Uniform, thin lines drawn across the surfaces of a section view to denote areas where the cutting plane has sliced directly through solid material.\n * **Viewing Arrows on Cutting Plane Lines:** The arrows located at the ends of a cutting plane line indicate the **direction of the view** (the line of sight of the observer viewing the sectioned part), not the direction of the cut or material removal.\n\n![Dial caliper with inside measuring jaws indicated](https://assets.knowt.com/pdf-flow-prod/48806193-1b89-481f-852c-cd0d858db1bb-figures/9.png)\n\n* **Dial Caliper Architecture and Operation:**\n * **Major Components:**\n * *Outside Measuring Jaws:* Lower, large jaws used to measure external thicknesses, diameters, and lengths.\n * *Inside Measuring Jaws:* Upper, smaller pointed jaws (circled in standard operational schematics) used to measure internal diameters of holes, bore sizes, and slot widths.\n * *Depth Measurement Rod:* Thin protruding rod extending from the base/end of the beam used to measure cavity and hole depths.\n * *Blade / Main Beam:* Graduated bar showing coarse measurement divisions, typically marked in whole inches and tenths of an inch (0.1\,\text{in.} increments).\n * *Dial Indicator:* Fine circular dial graduated in thousandths of an inch (0.001\,\text{in.}perline),typicallycompletingonefullrevolution(per line), typically completing one full revolution (0.100\,\text{in.}) for every tenth-inch travel along the beam.\n * *Bezel Clamp / Thumb Roll:* Mechanisms to zero-set the dial and provide smooth mechanical slide adjustment.\n * **Reading Procedure for a Standard Inch Dial Caliper:**\n 1. Read the largest whole inch visible on the main beam to the left of the slider edge.\n 2. Read the tenths of an inch (0.100\,\text{in.} increments) exposed on the main beam.\n 3. Read the dial needle indication directly, which gives the thousandths of an inch (0.001\,\text{in.}).\n 4. Sum the three values together:\n            \text{Total Measurement} = \text{Inches} + \text{Tenths} + \text{Dial Thousandths}\n\n![Dial caliper dial indicator measuring in thousandths of an inch](https://assets.knowt.com/pdf-flow-prod/48806193-1b89-481f-852c-cd0d858db1bb-figures/10.png)\n\n\n# Statistical Analysis in Engineering\n\n* **Descriptive Statistics vs. Inferential Statistics:**\n * **Descriptive Statistics:** Summarize, describe, and display the quantitative characteristics or features of a specific collected data set without drawing broader conclusions beyond the observed numbers.\n * **Inferential Statistics:** Utilize sample data to test formal hypotheses, uncover underlying patterns, and deduce or assess whether observed properties can be generalized to an entire broader population.\n\n* **Formulas for Standard Deviation:**\n * Standard deviation quantifies the dispersion or spread of values around the arithmetic mean.\n * **Population Standard Deviation (\sigma):**\n * Used when the researcher has a data value for every individual member of the entire population of interest.\n        \sigma = \sqrt{\frac{\sum (x_i - \mu)^2}{n}}\n * \mu = Population average (mean)\n * x_i = Individual measured values in the population\n * n = Total count of values in the population\n * **Sample Standard Deviation (s):**\n * An estimate of the spread of data within a larger population.\n * Used when values are available only for a subset (sample) of the population, generalizing the sample findings to the broader population.\n * Employs Bessel's correction (n - 1 in the denominator) to provide an unbiased estimate.\n        s = \sqrt{\frac{\sum (x_i - \bar{x})^2}{n - 1}}\n * \bar{x} = Sample average (mean)\n * x_i = Individual measured values in the sample\n * n = Count of values in the sample\n\n* **Step-by-Step Data Set Computations:**\n * **Data Set A (Cordless Phone Prices in Dollars):**\n * Values: `35, 50, 60, 60, 75, 65, 80‘(` (n = 7)\n * Sum: \sum x_i = 35 + 50 + 60 + 60 + 75 + 65 + 80 = 425\n * Mean:\n            \bar{x} = \frac{425}{7} \approx 60.71\,\text{dollars}\n * Sum of Squared Deviations:\n            \sum (x_i - \bar{x})^2 = (-25.71)^2 + (-10.71)^2 + (-0.71)^2 + (-0.71)^2 + (14.29)^2 + (4.29)^2 + (19.29)^2 \approx 1371.43\n * Sample Variance: s^2 = \frac{1371.43}{6} \approx 228.57\n * Sample Standard Deviation:\n            s = \sqrt{228.57} \approx 15.12\,\text{dollars}\n * Population Standard Deviation (if treated as entire population):\n            \sigma = \sqrt{\frac{1371.43}{7}} \approx \sqrt{195.92} \approx 14.00\,\text{dollars}\n * **Data Set B (Regular Season Home Runs - 10 Batters):**\n * Values: `51, 48, 47, 46, 45, 43, 41, 40, 40, 39‘(` (n = 10)\n * Sum: \sum x_i = 51 + 48 + 47 + 46 + 45 + 43 + 41 + 40 + 40 + 39 = 440\n * Mean:\n            \bar{x} = \frac{440}{10} = 44.0\,\text{home runs}\n * Deviations (x_i - \bar{x}):‘): `+7, +4, +3, +2, +1, -1, -3, -4, -4, -5`\n * Sum of Squared Deviations:\n            \sum (x_i - \bar{x})^2 = 49 + 16 + 9 + 4 + 1 + 1 + 9 + 16 + 16 + 25 = 146\n * Sample Variance: s^2 = \frac{146}{9} \approx 16.22\n * Sample Standard Deviation:\n            s = \sqrt{\frac{146}{9}} \approx 4.03\,\text{home runs}\n * Population Standard Deviation:\n            \sigma = \sqrt{\frac{146}{10}} = \sqrt{14.6} \approx 3.82\,\text{home runs}\n * **Data Set C (Department of Motor Vehicles Waiting Times in Minutes):**\n * Values: `11, 7, 14, 2, 8, 13, 3, 6, 10, 3, 8, 4, 8, 4, 7‘(` (n = 15)\n * Sum: \sum x_i = 108\n * Mean:\n            \bar{x} = \frac{108}{15} = 7.20\,\text{minutes}\n * Deviations (x_i - \bar{x}):‘): `3.8, -0.2, 6.8, -5.2, 0.8, 5.8, -4.2, -1.2, 2.8, -4.2, 0.8, -3.2, 0.8, -3.2, -0.2`\n * Squared Deviations: `14.44, 0.04, 46.24, 27.04, 0.64, 33.64, 17.64, 1.44, 7.84, 17.64, 0.64, 10.24, 0.64, 10.24, 0.04`\n * Sum of Squared Deviations: \sum (x_i - \bar{x})^2 = 188.40\n * Sample Variance: s^2 = \frac{188.40}{14} \approx 13.457\n * Sample Standard Deviation:\n            s = \sqrt{\frac{188.40}{14}} \approx 3.67\,\text{minutes}\n * Population Standard Deviation:\n            \sigma = \sqrt{\frac{188.40}{15}} = \sqrt{12.56} \approx 3.54\,\text{minutes}\n\n\n# The Empirical Rule, Histograms, and Normal Distributions\n\n![Normal distribution bell curve partitioned according to the Empirical Rule](https://assets.knowt.com/pdf-flow-prod/053a3470-4f69-459e-9d99-d73bf7c6da81-figures/2.jpg)\n\n* **The Empirical Rule (68-95-99.7 Rule):**\n * Applies specifically to continuous, bell-shaped normal distributions.\n * States that almost all observed data points lie within 3 standard deviations of the mean:\n * **68\%∗∗ofobservationsfallwithin** of observations fall within1standarddeviationofthemean:standard deviation of the mean:[\mu - 1\sigma, \mu + 1\sigma](or(or[\bar{x} - 1s, \bar{x} + 1s]).\n * **95\%∗∗ofobservationsfallwithin** of observations fall within2standarddeviationsofthemean:standard deviations of the mean:[\mu - 2\sigma, \mu + 2\sigma](or(or[\bar{x} - 2s, \bar{x} + 2s]).\n * **99.7\%∗∗ofobservationsfallwithin** of observations fall within3standarddeviationsofthemean:standard deviations of the mean:[\mu - 3\sigma, \mu + 3\sigma](or(or[\bar{x} - 3s, \bar{x} + 3s]).\n * **Specific Symmetrical Segment Probabilities:**\n * Between \muandand\mu + 1\sigma::34.0\%\n * Between \mu - 1\sigmaandand\mu::34.0\%\n * Between \mu + 1\sigmaandand\mu + 2\sigma::13.5\%\n * Between \mu - 2\sigmaandand\mu - 1\sigma::13.5\%\n * Between \mu + 2\sigmaandand\mu + 3\sigma::2.35\%\n * Between \mu - 3\sigmaandand\mu - 2\sigma::2.35\%\n * Beyond \mu + 3\sigma::0.15\%\n * Below \mu - 3\sigma::0.15\%\n\n* **Applied Empirical Rule Calculations:**\n * **Sample Data Analysis (\bar{x} = 0.08,,s = 1.77):**\n * 68\% of observations lie between:\n            0.08 - 1.77 = -1.69 \quad \text{and} \quad 0.08 + 1.77 = 1.88\n * 95\% of observations lie between:\n            0.08 - 2(1.77) = 0.08 - 3.54 = -3.46 \quad \text{and} \quad 0.08 + 3.54 = 3.62\n * **Fling Machine Instant Challenge Launcher Data:**\n * A statistical test yields a sample mean \bar{x} = 2.35\,\text{ft}andsamplestandarddeviationand sample standard deviations = 0.76\,\text{ft}.\n * **68\% Interval Prediction:**\n            \bar{x} \pm s: \quad 2.35 - 0.76 = 1.59\,\text{ft}, \quad 2.35 + 0.76 = 3.26\,\text{ft}\n            Approximately 68\%oflauncheswillachieveadistancebetweenof launches will achieve a distance between1.59\,\text{ft}andand3.26\,\text{ft}.\n * **95\% Interval Prediction:**\n            \bar{x} \pm 2s: \quad 2.35 - 2(0.76) = 2.35 - 1.52 = 0.83\,\text{ft}, \quad 2.35 + 2(0.76) = 2.35 + 1.52 = 3.87\,\text{ft}\n            Approximately 95\%oflauncheswillachieveadistancebetweenof launches will achieve a distance between0.83\,\text{ft}andand3.87\,\text{ft}.\n\n![Normal distribution curve for freshman biology test scores](https://assets.knowt.com/pdf-flow-prod/48806193-1b89-481f-852c-cd0d858db1bb-figures/18.png)\n\n* **Freshman Biology Examination Case Study (N = 2000,,\mu = 70,,\sigma = 5):**\n * **Standard Deviation Boundaries:**\n * \mu - 3\sigma = 70 - 3(5) = 55\n * \mu - 2\sigma = 70 - 2(5) = 60\n * \mu - 1\sigma = 70 - 1(5) = 65\n * \mu = 70\n * \mu + 1\sigma = 70 + 1(5) = 75\n * \mu + 2\sigma = 70 + 2(5) = 80\n * \mu + 3\sigma = 70 + 3(5) = 85\n * **Probability and Student Count Solutions:**\n * *Percentage of scores between 60 and 75:* Range spans \mu - 2\sigmatoto\mu + 1\sigma.\n            \text{Sum} = 13.5\% + 34.0\% + 34.0\% = 81.5\%\n * *Percentage of scores between 60 and 70:* Range spans \mu - 2\sigmatoto\mu.\n            \text{Sum} = 13.5\% + 34.0\% = 47.5\%\n * *Percentage of scores between 60 and 85:* Range spans \mu - 2\sigmatoto\mu + 3\sigma.\n            \text{Sum} = 13.5\% + 34.0\% + 34.0\% + 13.5\% + 2.35\% = 97.35\%\n * *Percentage of scores less than 55:* Region below \mu - 3\sigma.\n            \text{Percentage} = 0.15\%\n * *Percentage of scores greater than 80:* Region above \mu + 2\sigma.\n            \text{Percentage} = 2.35\% + 0.15\% = 2.50\%\n * *Number of students scoring between 60 and 70:*\n            2000 \times 0.475 = 950\,\text{students}\n * *Number of students scoring between 55 and 60:*\n            Span is [\mu - 3\sigma, \mu - 2\sigma],representing, representing2.35\%\n            2000 \times 0.0235 = 47\,\text{students}\n\n![Cumulative frequency histogram of driver safety exam scores](https://assets.knowt.com/pdf-flow-prod/48806193-1b89-481f-852c-cd0d858db1bb-figures/16.png)\n\n* **Analysis of Driver Safety Exam Cumulative Frequency Histogram:**\n * Context: Passing score requires answering at least 45outofout of50 questions correctly.\n * Cumulative Frequency Data Table:\n * Score Interval 45:Cumulativefrequency=: Cumulative frequency =2\n * Score Interval 45\text{--}46:Cumulativefrequency=: Cumulative frequency =4\n * Score Interval 45\text{--}47:Cumulativefrequency=: Cumulative frequency =8\n * Score Interval 45\text{--}48:Cumulativefrequency=: Cumulative frequency =9\n * Score Interval 45\text{--}49:Cumulativefrequency=: Cumulative frequency =14\n * Score Interval 45\text{--}50:Cumulativefrequency=: Cumulative frequency =20\n * **Evaluations:**\n * *Total number of people who passed the exam:* The final cumulative bin (45\text{--}50)reaches) reaches20.Therefore,∗∗. Therefore, **20** people passed.\n * *Number of people who answered exactly 49 questions correctly:* Calculated by subtracting the cumulative frequency of score 48orlessfromthatofscoreor less from that of score49 or less:\n            14 - 9 = 5\,\text{people}\n * *Number of people who received a score of 48 or less:* Given directly by the cumulative bar for 45\text{--}48,whichis∗∗, which is **9** people.\n\n![Frequency table and histogram interval comparison](https://assets.knowt.com/pdf-flow-prod/48806193-1b89-481f-852c-cd0d858db1bb-figures/17.png)\n\n* **Construction and Identification of Frequency Histograms:**\n * Frequency Table Data:\n * Interval 4\text{--}8:Frequency=: Frequency =8\n * Interval 9\text{--}13:Frequency=: Frequency =3\n * Interval 14\text{--}18:Frequency=: Frequency =10\n * Interval 19\text{--}23:Frequency=: Frequency =5\n * Matching Criteria: The correct histogram must align each bar height precisely with the table frequency for each discrete bin: bar 1 at height 8,bar2atheight, bar 2 at height3,bar3atheight, bar 3 at height10,andbar4atheight, and bar 4 at height5$$ (represented by Histogram D).