Comprehensive Semiconductor Physics and Electronics Study Notes

Energy Gap and Classification of Materials

  • Energy gap (EgE_g) comparison among material classes:

    • Insulators: Eg>5.0 eVE_g > 5.0\,\text{eV}

    • Semiconductors: Eg<1.0 eVE_g < 1.0\,\text{eV} (typically around 0.7 eV0.7\,\text{eV} to 1.5 eV1.5\,\text{eV})

    • Conductors (Metals): Eg≈0E_g \approx 0

  • Relationship between energy gap and resistance: Higher energy gap (EgE_g) results in higher electrical resistance.

  • Materials classified by conductivity and bonding:

    • Insulators: Ionic bonding. Examples include diamond, mica, glass, and ceramic. Bad conductors of current due to very large energy gaps; they do not allow current flow under normal conditions.

    • Metals (Conductors): Metallic bonding. Conduction band (CB) and valence band (VB) overlap even at T=0 KT = 0\,\text{K}. Exhibit a positive temperature coefficient of resistance (positive temperature gradient). Free electron concentration in metals is virtually independent of temperature.

    • Semiconductors: Covalent bonding. Bipolar charge transport mechanism (current flows due to both free electrons and holes).

Thermal Voltage and Electron Volt

  • Thermal Voltage (VTV_T):

    • Defined as the voltage equivalent of temperature.

    • Mathematical expression:     VT=kTqV_T = \frac{k T}{q}

    • Constants:

    • Boltzmann's constant: k=1.38×10−23 J/Kk = 1.38 \times 10^{-23}\,\text{J/K}

    • Electronic charge: q=1.6×10−19 Cq = 1.6 \times 10^{-19}\,\text{C}

    • Simplified relation:     VT=T11600 VV_T = \frac{T}{11600}\,\text{V}

    • Alternative expression:     VT≈86×10−6T VV_T \approx 86 \times 10^{-6} T\,\text{V}

    • Temperature sensitivity: For a large variation in temperature (TT), there is only a small variation in thermal voltage (VTV_T).

  • Electron Volt (eV):

    • Practical unit of energy in electronics.

    • Definition: The energy gained or lost by an electron moving through a potential difference (PD) of 1 Volt.

    • Conversion:     1 eV=1.6×10−19 J1\,\text{eV} = 1.6 \times 10^{-19}\,\text{J}

    • Indicates kinetic energy gained (KEKE) or potential energy lost (PEPE) by an electron:     KE=PE⇒12mv2=qVKE = PE \Rightarrow \frac{1}{2} m v^2 = q V

    • Electron velocity expression:     v=2qVmv = \sqrt{\frac{2 q V}{m}}

Temperature Dependence of Energy Gap

  • In semiconductors and insulators, the energy gap (EgE_g) decreases as temperature increases (↑T⇒↓Eg\uparrow T \Rightarrow \downarrow E_g).

  • Temperature dependence equation:   Eg(T)=Eg0−βTE_g(T) = E_{g0} - \beta T

    • Eg0E_{g0}: Energy gap at 0 K0\,\text{K}

    • β\beta: Material constant

  • Empirical relations for specific semiconductors:

    • Silicon (Si):     Eg(T)=1.21−3.6×10−4×T eVE_g(T) = 1.21 - 3.6 \times 10^{-4} \times T\,\text{eV}

    • At T=0 KT = 0\,\text{K}, Eg0=1.21 eVE_{g0} = 1.21\,\text{eV}.

    • At T=300 KT = 300\,\text{K}, Eg≈1.1 eVE_g \approx 1.1\,\text{eV}.

    • Germanium (Ge):     Eg(T)=0.785−2.2×10−4×T eVE_g(T) = 0.785 - 2.2 \times 10^{-4} \times T\,\text{eV}

    • At T=0 KT = 0\,\text{K}, Eg0=0.785 eVE_{g0} = 0.785\,\text{eV}.

    • At T=300 KT = 300\,\text{K}, Eg≈0.72 eVE_g \approx 0.72\,\text{eV}.

Charge Carrier Mobility and Drift Mechanism

  • Electric Field Intensity (EE):   E=−dVdxE = -\frac{dV}{dx}

  • Mobility (μ\mu):

    • Defined as the ratio of drift velocity (vdv_d) to applied electric field intensity (EE):     μ=vdE\mu = \frac{v_d}{E}

    • Units: cm2/V⋅s\text{cm}^2/\text{V}\cdot\text{s} or m2/V⋅s\text{m}^2/\text{V}\cdot\text{s}.

    • Physical meaning: Indicates how fast charge carriers move through a crystal lattice under an electric field.

    • Carrier mobility values at room temperature (T=300 KT = 300\,\text{K}):

    • Germanium (Ge): Electron mobility μn=3800 cm2/V⋅s\mu_n = 3800\,\text{cm}^2/\text{V}\cdot\text{s}, Hole mobility μp=1800 cm2/V⋅s\mu_p = 1800\,\text{cm}^2/\text{V}\cdot\text{s}.

    • Silicon (Si): Electron mobility μn=1300 cm2/V⋅s\mu_n = 1300\,\text{cm}^2/\text{V}\cdot\text{s}, Hole mobility μp=500 cm2/V⋅s\mu_p = 500\,\text{cm}^2/\text{V}\cdot\text{s}.

    • Ratio of electron mobility to hole mobility in Silicon:     μnμp=1300500=2.6\frac{\mu_n}{\mu_p} = \frac{1300}{500} = 2.6

    • Electron mobility is always greater than hole mobility (μn>μp\mu_n > \mu_p) because free electrons move in the conduction band, whereas holes move via valence band electron transitions.

    • High electron mobility in Germanium makes it suitable for high-frequency applications, while Silicon is preferred for high-temperature applications.

  • Drift Current: Flow of electric current produced by the movement of charge carriers under the influence of an applied electric field.

  • Temperature Effect on Mobility:

    • As temperature increases, lattice atoms vibrate more violently, causing increased thermal scattering of charge carriers, which decreases mobility (↑T⇒↓μ\uparrow T \Rightarrow \downarrow \mu).

    • Non-linear temperature variation model:     μ∝T−m\mu \propto T^{-m}

    • For Germanium: me=1.66m_e = 1.66 (electrons), mh=2.33m_h = 2.33 (holes).

    • For Silicon: me=2.5m_e = 2.5 (electrons), mh=2.7m_h = 2.7 (holes).

  • Mobility vs. Electric Field Relationship:

    • Low electric field intensity (E<103 V/cmE < 10^3\,\text{V/cm}): Mobility μ\mu remains constant; drift velocity increases linearly with EE (vd=μEv_d = \mu E).

    • High electric field intensity (E>104 V/cmE > 10^4\,\text{V/cm}): Carrier velocity reaches a maximum threshold called saturation drift velocity (vd,satv_{d,\text{sat}}). Mobility becomes inversely proportional to electric field (μ∝1E\mu \propto \frac{1}{E}), describing a hyperbola.

Carrier Diffusion and Einstein Relation

  • Diffusion Current:

    • Migration of charge carriers from a region of higher concentration to a region of lower concentration due to a concentration gradient. It is a natural random thermal phenomenon.

    • Diffusion current flows exclusively in semiconductors due to non-uniform distribution of charge carriers.

    • Concentration gradients:

    • Electron concentration gradient: dndx\frac{dn}{dx}

    • Hole concentration gradient: dpdx\frac{dp}{dx}

  • Einstein Relation:

    • Relates carrier diffusion constant (DD), mobility (μ\mu), and thermal voltage (VTV_T):     Dnμn=Dpμp=VT=kTq=T11600\frac{D_n}{\mu_n} = \frac{D_p}{\mu_p} = V_T = \frac{k T}{q} = \frac{T}{11600}

    • Diffusion constant equations:     Dn=μnVTD_n = \mu_n V_T     Dp=μpVTD_p = \mu_p V_T

    • SI Unit for diffusion constants: m2/s\text{m}^2/\text{s} or cm2/s\text{cm}^2/\text{s}.

    • Physical role: Measures how fast charge carriers spread out from regions of high concentration to low concentration due to random thermal motion.

  • Diffusion Length (LL):

    • Average distance a minority carrier travels before recombining.     L=D⋅τL = \sqrt{D \cdot \tau}

    • Substituting Einstein relation:     L=μ⋅VT⋅τL = \sqrt{\mu \cdot V_T \cdot \tau}

    • Diffusion length depends on four parameters: mobility (μ\mu), carrier lifetime (τ\tau), temperature (TT), and diffusion constant (DD).

Numerical Examples and Calculations

  • Problem 1: Calculation of mobility from drift velocity

    • Given: Drift velocity vd=5 cm/sv_d = 5\,\text{cm/s}, Electric field E=100 V/cmE = 100\,\text{V/cm}.

    • Solution:     μ=vdE=5100=0.05 cm2/V⋅s\mu = \frac{v_d}{E} = \frac{5}{100} = 0.05\,\text{cm}^2/\text{V}\cdot\text{s}

  • Problem 2: Calculation of mobility from diffusion constant

    • Given: Diffusion constant D=0.014 m2/sD = 0.014\,\text{m}^2/\text{s} at T=300 KT = 300\,\text{K}.

    • Solution:     VT=30011600 VV_T = \frac{300}{11600}\,\text{V}     μ=DVT=0.014×11600300=0.5413 m2/V⋅s\mu = \frac{D}{V_T} = \frac{0.014 \times 11600}{300} = 0.5413\,\text{m}^2/\text{V}\cdot\text{s}

  • Problem 3: Diffusion constant at elevated temperatures

    • Given: Carrier mobility μ=0.5 m2/V⋅s\mu = 0.5\,\text{m}^2/\text{V}\cdot\text{s}.

    • i) At T=300 KT = 300\,\text{K}:     D=μ×VT=0.5×30011600≈0.0129 m2/sD = \mu \times V_T = 0.5 \times \frac{300}{11600} \approx 0.0129\,\text{m}^2/\text{s}

    • ii) At T=500 KT = 500\,\text{K}:     D=0.5×50011600≈0.0215 m2/sD = 0.5 \times \frac{500}{11600} \approx 0.0215\,\text{m}^2/\text{s}

  • Problem 4: Minority carrier diffusion length

    • Given: Minority carrier lifetime τ=100 μs=100×10−6 s\tau = 100\,\mu\text{s} = 100 \times 10^{-6}\,\text{s}, Diffusion constant D=100 cm2/sD = 100\,\text{cm}^2/\text{s}.

    • Solution:     L=D⋅τ=100×100×10−6=10−2=0.1 cmL = \sqrt{D \cdot \tau} = \sqrt{100 \times 100 \times 10^{-6}} = \sqrt{10^{-2}} = 0.1\,\text{cm}

  • Problem 5: Electron drift velocity and transit time across wafer

    • Given: Wafer thickness d=0.5 mm=0.5×10−3 md = 0.5\,\text{mm} = 0.5 \times 10^{-3}\,\text{m}, Applied potential V=100 mV=0.1 VV = 100\,\text{mV} = 0.1\,\text{V}, Mobility μ=0.02 m2/V⋅s\mu = 0.02\,\text{m}^2/\text{V}\cdot\text{s}.

    • Solution:     E=Vd=100×10−30.5×10−3=200 V/mE = \frac{V}{d} = \frac{100 \times 10^{-3}}{0.5 \times 10^{-3}} = 200\,\text{V/m}     vd=μE=0.02×200=4 m/sv_d = \mu E = 0.02 \times 200 = 4\,\text{m/s}     t=dvd=0.5×10−34=1.25×10−4 s=125 μst = \frac{d}{v_d} = \frac{0.5 \times 10^{-3}}{4} = 1.25 \times 10^{-4}\,\text{s} = 125\,\mu\text{s}

  • Problem 6: Electron and hole diffusion constants in Germanium and Silicon at 300 K

    • Germanium (μn=3800\mu_n = 3800, μp=1800\mu_p = 1800\,cm2/V⋅s\text{cm}^2/\text{V}\cdot\text{s}):     Dn=3800×30011600≈98.28 cm2/sD_n = 3800 \times \frac{300}{11600} \approx 98.28\,\text{cm}^2/\text{s}     Dp=1800×30011600≈46.55 cm2/sD_p = 1800 \times \frac{300}{11600} \approx 46.55\,\text{cm}^2/\text{s}

    • Silicon (μn=1300\mu_n = 1300, μp=500\mu_p = 500\,cm2/V⋅s\text{cm}^2/\text{V}\cdot\text{s}):     Dn=1300×30011600≈33.62 cm2/sD_n = 1300 \times \frac{300}{11600} \approx 33.62\,\text{cm}^2/\text{s}     Dp=500×30011600≈12.93 cm2/sD_p = 500 \times \frac{300}{11600} \approx 12.93\,\text{cm}^2/\text{s}

Conductivity, Resistivity, and Current Density Equations

  • Resistivity (ρ\rho): Specific resistance of a material.   R=ρlAR = \rho \frac{l}{A}

    • SI Unit: Ω⋅m\Omega\cdot\text{m} or Ω⋅cm\Omega\cdot\text{cm}.

  • Conductivity (σ\sigma): Reciprocal of resistivity (σ=1ρ\sigma = \frac{1}{\rho}). Represents current-carrying capacity.   σ=carrier concentration×charge×mobility\sigma = \text{carrier concentration} \times \text{charge} \times \text{mobility}

    • General semiconductor conductivity equation (bipolar transport):     σ=nqμn+pqμp=q(nμn+pμp)\sigma = n q \mu_n + p q \mu_p = q (n \mu_n + p \mu_p)

  • Current Density (JJ) in Semiconductors:

    • Total current density is the vector sum of drift and diffusion current densities:     J=Jdrift+JdiffJ = J_{\text{drift}} + J_{\text{diff}}

    • Electron drift current density: Jn,drift=nqμnEJ_{n,\text{drift}} = n q \mu_n E

    • Hole drift current density: Jp,drift=pqμpEJ_{p,\text{drift}} = p q \mu_p E

    • Electron diffusion current density: Jn,diff=qDndndxJ_{n,\text{diff}} = q D_n \frac{dn}{dx}

    • Hole diffusion current density: Jp,diff=−qDpdpdxJ_{p,\text{diff}} = -q D_p \frac{dp}{dx}

    • Total electron current density:     Jn=nqμnE+qDndndxJ_n = n q \mu_n E + q D_n \frac{dn}{dx}

    • Total hole current density:     Jp=pqμpE−qDpdpdxJ_p = p q \mu_p E - q D_p \frac{dp}{dx}

    • Combined total current density:     J=(nqμn+pqμp)E+qDndndx−qDpdpdxJ = (n q \mu_n + p q \mu_p) E + q D_n \frac{dn}{dx} - q D_p \frac{dp}{dx}

    • Total current I=J×AreaI = J \times \text{Area}.

  • Temperature Dependence of Semiconductor Conductivity:

    • As temperature rises, carrier mobility decreases slightly. However, thermal energy breaks a huge number of covalent bonds, exponentially increasing carrier concentration (nin_i).

    • Because the exponential increase in concentration dominates over mobility reduction, total conductivity of semiconductors increases significantly with temperature (negative temperature coefficient of resistance).

Comparative Material Properties: Silicon vs. Germanium

  • Parameter comparison at T=300 KT = 300\,\text{K}:

    • Atomic Number: Ge = 32, Si = 14.

    • Atomic Density: Ge = 4.421×1022 atoms/cm34.421 \times 10^{22}\,\text{atoms/cm}^3, Si = 5.0×1022 atoms/cm35.0 \times 10^{22}\,\text{atoms/cm}^3

    • Intrinsic Carrier Concentration (nin_i): Ge = 2.5×1013 cm−32.5 \times 10^{13}\,\text{cm}^{-3}, Si = 1.5×1010 cm−31.5 \times 10^{10}\,\text{cm}^{-3}

    • Intrinsic Resistivity: Ge = 45 Ω⋅cm45\,\Omega\cdot\text{cm}, Si = 230000 Ω⋅cm230000\,\Omega\cdot\text{cm}

    • Leakage Current: Ge = μA\mu\text{A} range, Si = nA\text{nA} range.

    • Maximum Operating Temperature: Ge = 75∘C75^\circ\text{C} (range 60∘C60^\circ\text{C} to 75∘C75^\circ\text{C}), Si = 175∘C175^\circ\text{C} (range 60∘C60^\circ\text{C} to 175∘C175^\circ\text{C}).

    • Power Handling Capability: Ge = Low, Si = High.

  • Reasons Silicon is Preferred over Germanium in Semiconductor Manufacturing:

    1. Significantly smaller reverse leakage current.

    2. Higher maximum operating temperature capability (175∘C175^\circ\text{C} vs 75∘C75^\circ\text{C}).

    3. Higher power handling capacity.

    4. High abundance on Earth's crust (silica/sand) leading to lower raw material cost.

    5. Ability to easily grow a stable, high-quality native oxide layer (Silicon Dioxide, SiO2\text{SiO}_2), which is essential for planar technology and integrated circuit fabrication.

  • Disadvantage of Silicon: High intrinsic resistivity (230000 Ω⋅cm230000\,\Omega\cdot\text{cm}), resulting in low conductivity in its pure form.

  • Why Carbon is Not Used as a Semiconductor:

    • Carbon belongs to Group IV of the periodic table, but its energy gap in diamond form is around 5.5 eV5.5\,\text{eV}.

    • Carbon exhibits unstable and unpredictable physical/electrical properties: acts as a good conductor in graphite allotrope and an insulator in diamond allotrope.

Compound Semiconductors: Gallium Arsenide (GaAs)

  • Artificially synthesized compound from Group III (Gallium) and Group V (Arsenic).

  • Direct bandgap semiconductor with Eg=1.47 eVE_g = 1.47\,\text{eV}.

  • High mobility: Electron mobility μn≈8500 cm2/V⋅s\mu_n \approx 8500\,\text{cm}^2/\text{V}\cdot\text{s} (or 5600 cm2/V⋅s5600\,\text{cm}^2/\text{V}\cdot\text{s} depending on doping level), Hole mobility μp≈400 cm2/V⋅s\mu_p \approx 400\,\text{cm}^2/\text{V}\cdot\text{s}.

  • Recombination energy is released directly as photons (light).

  • Exhibits Negative Differential Mobility, making it ideal for microwave device applications.

  • Low-noise material characteristic.

  • Applications: Fabrication of Light Emitting Diodes (LEDs), Tunnel Diodes, Varactor Diodes, PIN Diodes, IMPATT Diodes, and Gunn Diodes.

  • Indium Phosphide (InP) is another compound semiconductor utilized for high-frequency optoelectronic devices.

Intrinsic Semiconductors and Generation-Recombination

  • Pure, undoped semiconductor material (non-degenerate semiconductor).

  • Tetravalent crystal structure: 4 valence electrons forming covalent bonds with 4 neighboring atoms.

  • Band structure conditions:

    • At T=0 KT = 0\,\text{K}: Conduction band is completely empty, valence band is completely filled. Acts as a perfect insulator.

    • At T=300 KT = 300\,\text{K}: Thermal energy breaks covalent bonds. Electrons move from VB to CB, leaving behind electron deficiencies (holes) in the valence band.

  • Holes:

    • Defined as the deficiency of an electron in a broken covalent bond.

    • Behaves as a mobile positive charge carrier with magnitude +1.6×10−19 C+1.6 \times 10^{-19}\,\text{C}.

  • Intrinsic carrier condition: Electron concentration equals hole concentration (n=p=nin = p = n_i).

  • Intrinsic conductivity equation:   σi=niq(μn+μp)\sigma_i = n_i q (\mu_n + \mu_p)

  • Temperature dependence of intrinsic concentration (nin_i):   ni2=A0T3e−Eg0kTn_i^2 = A_0 T^3 e^{-\frac{E_{g0}}{k T}}   ni=A01/2T3/2e−Eg02kTn_i = A_0^{1/2} T^{3/2} e^{-\frac{E_{g0}}{2 k T}}

    • The exponential bandgap term e−Eg02kTe^{-\frac{E_{g0}}{2 k T}} is the dominating factor governing carrier concentration.

  • Generation and Recombination:

    • Generation: Thermal excitation breaks covalent bonds, creating electron-hole pairs (EHPs).

    • Recombination: Free electron in conduction band falls back into a valence band hole, causing both carriers to disappear and restoring a covalent bond.

    • Carrier Lifetime (τ\tau): Average time duration between the generation of a carrier pair and its recombination. Measured in nanoseconds (ns) or microseconds (μ\mus).

  • Temperature Coefficients of Intrinsic Conductivity:

    • For Germanium: Conductivity increases by approximately 6%6\% per 1∘C1^\circ\text{C} rise in temperature.

    • For Silicon: Conductivity increases by approximately 8%8\% per 1∘C1^\circ\text{C} rise in temperature.

Mass Action Law and Reverse Leakage Current

  • Mass Action Law:

    • Under thermal equilibrium, the product of free electron concentration (nn) and hole concentration (pp) in any semiconductor (intrinsic or extrinsic) is constant and equal to the square of intrinsic carrier concentration (nin_i):     n⋅p=ni2n \cdot p = n_i^2

    • Crucial formula used to compute minority carrier concentration in extrinsic semiconductors.

  • Reverse Leakage Current (IoI_o):

    • Also called minority carrier current, reverse saturation current, or thermally generated current.

    • Governed entirely by minority carriers generated via thermal energy.

    • Thermal sensitivity rule: Leakage current doubles for every 10∘C10^\circ\text{C} rise in temperature:     Io(T2)=Io(T1)×2T2−T110I_o(T_2) = I_o(T_1) \times 2^{\frac{T_2 - T_1}{10}}

    • Corresponds to approximately 7%7\% increase per 1∘C1^\circ\text{C} temperature increase.

  • Problem 7: Reverse leakage current calculation

    • Given: In Silicon at 300 K300\,\text{K}, leakage current Io=1.5×10−9 AI_o = 1.5 \times 10^{-9}\,\text{A}. Find leakage current at 350 K350\,\text{K}.

    • Solution:     ΔT=350−300=50∘C\Delta T = 350 - 300 = 50^\circ\text{C}     Io(350 K)=1.5×10−9×250/10=1.5×10−9×25=1.5×10−9×32=48×10−9 A=48 nAI_o(350\,\text{K}) = 1.5 \times 10^{-9} \times 2^{50/10} = 1.5 \times 10^{-9} \times 2^5 = 1.5 \times 10^{-9} \times 32 = 48 \times 10^{-9}\,\text{A} = 48\,\text{nA}

Extrinsic Semiconductors: N-Type and P-Type

  • Extrinsic semiconductors are created by adding controlled quantities of specific impurity atoms to pure semiconductor wafers (a process called doping).

  • Doping increases conductivity without requiring temperature increases that lead to thermal instability.

  • N-Type Semiconductors:

    • Impurity added: Pentavalent elements (Group V) such as Phosphorus (P), Arsenic (As), or Antimony (Sb). Phosphorus is widely used.

    • Impurity action: Donates one extra electron per atom; creates a Donor Energy Level (EDE_D) situated just below the conduction band edge (ECE_C).

    • Carrier concentrations: Free electrons are majority carriers (nnn_n), holes are minority carriers (pnp_n):     nn≫pnn_n \gg p_n     nn≈NDn_n \approx N_D

    • Conductivity formula:     σn≈NDqμn\sigma_n \approx N_D q \mu_n

  • P-Type Semiconductors:

    • Impurity added: Trivalent elements (Group III) such as Boron (B), Gallium (Ga), or Indium (In). Boron is widely used.

    • Impurity action: Accepts electrons from adjacent covalent bonds, creating holes; introduces an Acceptor Energy Level (EAE_A) situated just above the valence band edge (EVE_V).

    • Carrier concentrations: Holes are majority carriers (ppp_p), free electrons are minority carriers (npn_p):     pp≫npp_p \gg n_p     pp≈NAp_p \approx N_A

    • Conductivity formula:     σp≈NAqμp\sigma_p \approx N_A q \mu_p

Direct vs. Indirect Bandgap Semiconductors

  • Direct Bandgap Semiconductors:

    • Recombination energy is dissipated primarily as optical radiation (light):     ≈98% Light,2% Heat\approx 98\%\,\text{Light}, 2\%\,\text{Heat}

    • Transition mechanism: Falling electrons from CB transition directly to VB without altering crystal momentum vector (k\mathbf{k} vector remains constant).

    • Relatively short carrier lifetime.

    • Examples: Gallium Arsenide (GaAs), Gallium Nitride (GaN), Zinc Sulfide (ZnS), Cadmium Sulfide (CdS), Indium Phosphide (InP).

  • Indirect Bandgap Semiconductors:

    • Recombination energy is dissipated primarily as lattice vibrations (heat/phonons):     ≈98% Heat,2% Light\approx 98\%\,\text{Heat}, 2\%\,\text{Light}

    • Transition mechanism: Falling electrons collide with crystal lattice, altering kinetic energy and momentum vector before entering VB.

    • Relatively long carrier lifetime.

    • Examples: Silicon (Si), Germanium (Ge), Gallium Phosphide (GaP), Aluminum Phosphide (AlP), Lead Sulfide (PbS).

The Hall Effect

  • Statement: If a specimen (metal or semiconductor) carrying a current II is placed in a transverse magnetic field BB, an electric field EHE_H (Hall Electric Field) is induced in a direction perpendicular to both current II and magnetic field B$.\n- **Geometric Orientation:**\n - Current (I) along X-axis.\n - Magnetic Field (B) along Z-axis.\n - Induced Hall Electric Field (E_H) along Y-axis.\n- **Hall Voltage Formula:**\n  V_H = E_H \cdot d\n  V_H = \frac{B I}{\rho_w w} = \frac{R_H B I}{w}\n - d: Distance between top and bottom surfaces.\n - w: Width of specimen cross-section.\n - R_H:HallCoefficient,definedas: Hall Coefficient, defined asR_H = \frac{1}{\rho_{\text{charge}}} = \frac{1}{q n}oror\frac{1}{q p}.\n- **Polarity of Induced Hall Voltage:**\n - Metals and N-type Semiconductors: Negative (-ve) Hall voltage at top surface relative to bottom.\n - P-type Semiconductors: Positive (+ve) Hall voltage at top surface relative to bottom.\n - Intrinsic Semiconductors: Zero or negligible (0).\n- **Applications of Hall Effect:**\n 1. Determining whether a given semiconductor sample is N-type or P-type.\n 2. Measuring majority charge carrier concentration (nororp).\n 3. Calculating charge carrier mobility (\mu = \sigma |R_H|).\n 4. Measuring magnetic flux density (B) (Magnetic field meters / Gaussmeters).\n 5. Designing Hall Effect Transducers and Hall Effect Multipliers (output voltage proportional to product of current and magnetic field signals).\n 6. Measuring electromagnetic wave power.\n\n# Advanced Problems and Conceptual Review Questions\n\n- **Problem 8: Diffusion constant from mobility**\n - Given: Mobility of N-type semiconductor \mu = 4800\,\text{cm}^2/\text{V}\cdot\text{s}atatT = 300\,\text{K}.\n - Solution:\n    D = \mu \cdot V_T = 4800 \times \frac{300}{11600} \approx 4800 \times 0.02586 = 124.13\,\text{cm}^2/\text{s}\n- **Problem 9: Semiconductor type determination from doping concentrations**\n - Given: Donor impurity concentration N_D = 1.5 \times 10^{18}\,\text{cm}^{-3},Acceptorimpurityconcentration, Acceptor impurity concentrationN_A = 1.5 \times 10^{16}\,\text{cm}^{-3}.\n - Solution: Net donor density N_D - N_A = 1.5 \times 10^{18} - 0.015 \times 10^{18} = 1.485 \times 10^{18}\,\text{cm}^{-3} > 0. Therefore, the material is an N-type semiconductor.\n- **Problem 10: Electron velocity from Fermi energy at 0 K**\n - Given: Fermi level E_F = 1.02\,\text{eV}atatT = 0\,\text{K}.\n - Solution: Fermi energy represents the maximum kinetic energy possessed by electrons at 0\,\text{K}.\n    E_F = \frac{1}{2} m v^2\n    1.02\,\text{eV} = 1.02 \times 1.6 \times 10^{-19}\,\text{J} = 1.632 \times 10^{-19}\,\text{J}\n    v = \sqrt{\frac{2 E_F}{m}} = \sqrt{\frac{2 \times 1.632 \times 10^{-19}}{9.1 \times 10^{-31}}} = \sqrt{3.5868 \times 10^{11}} \approx 5.99 \times 10^5\,\text{m/s}\n- **Key Integrated Circuit Fabrication and Processing Concepts:**\n - **Fermi-Dirac Distribution:** Gives the probability F(E)thatanenergystatethat an energy stateEisoccupiedbyanelectronattemperatureis occupied by an electron at temperatureT:\n    F(E) = \frac{1}{1 + e^{\frac{E - E_F}{k T}}}\n - **Metallurgical Grade Silicon (MGS) to Electronic Grade Silicon (EGS):** MGS (\approx 98\%pure)isrefinedtoultra−pureEGSusingtrichlorosilane(pure) is refined to ultra-pure EGS using trichlorosilane (\text{SiHCl}_3$$) fractional distillation processes.

    • Czochralski Ingot Growth (CZ Method): Crystal growth technique utilized to pull single-crystal silicon ingots from molten silicon.

    • Monolithic IC and CMOS Fabrication: Process sequence involving oxidation, photolithography, ion implantation, diffusion, metallization, and etching to fabricate complementary MOSFET pairs.