SCIENCE TERM 1 GRD 9B

INERTIA - It is the ability of an object to resist force. 



E.g. a heavier object is harder to push because it has more inertia. It is RESISTING your push more compared to if you were pushing a lighter object. Typically, more mass = more inertia. 

ACCELERATION - It is the change in an object’s velocity. 



Ex. “A car speeding up after the traffic light turns green.” 

  • When a mass is constant, greater force is applied to produce greater acceleration.

  • Force () = Acceleration ()

  • Mass () = Acceleration ()

EQUATIONS FOR THE SECOND LAW OF MOTION:



VARIABLES

UNITS

Force (f)

Newton (N)

Mass (m)

Kilograms (kg)

Acceleration (a)

MPS (m/s2)




Example problem:



“A box weighs 20kg, and can accelerate at 5m/s2, what is the applied force needed for the box to move?”



G: Mass = 20kg, Acce. = 5m/s2

R: Force = ?

E: F = m x a

S: F = 20kg x 5m/s2

= 100N

A: “You will need 100N to push a 20kg box.

ACTION-REACTION (or INTERACTION) -

 “FOR EVERY ACTION, THERE IS AN EQUAL AND OPPOSITE REACTION” Simply, with every pull, there is a push, and vice versa. Every action and movement you do there’s an opposite force acting on it


A.) HOW TO GET THE NET FORCE! 



NOTE: Like how force is always measured, the final answer should have N (Newtons) as the unit of measure.


There’s 2 ways to go about this. 

On every object or body, there are 2 forces acting on it. Typically applied force, and frictional force. What operation you will use depends on the direction of both these forces.



  1. If both forces go the SAME DIRECTION, add both forces. (add the applied and frictional force, the value you get is the net force)

  2. If the forces go OPPOSITE DIRECTIONS, subtract the forces with each other. (Subtract the applied force by the frictional force) 


⚡ELECTRICITY AND ELECTRICAL SAFETY⚡

WHAT IS ELECTRICITY?



  • ELECTRICITY - it is the flow of ELECTRONS through a conductor or medium (like copper wire)



  • Electrons CARRY the ELECTRICAL ENERGY



  • It is a TYPE OF ENERGY, so electricity can be TRANSFORMED.

HOW TO BE SAFE?

  1. BEFORE USING DEVICES

  • Check for any frayed and/or exposed wires, damaged outlets, and cracks.

  • Do NOT TOUCH exposed wires.

  • Keep hands DRY (water is a conductor)



  1. WHILE USING

  • Follow the instructions on how to use it

  • Do NOT OVERLOAD THE OUTLET with too many devices, over heating and fires are a risk.

  • Keep appliances away from water

  • DO NOT INSERT METAL OBJECTS into outlets



  1. AFTER USING 

  • TURN OFF AND UNPLUG devices when not in use

  • HOLD THE PLUG  not THE CORD

  • Disconnect the power source from the device before making repairs, maintenance, or cleaning.



  1. PROTECTIVE COMPONENTS IN ELECTRICAL DEVICES

  • FUSE - piece of metal that melts when too much current passes through, ultimately stopping the circuit

  • CIRCUIT BREAKER - a device that stops the circuit when there’s too much current. It opens a switch to cut the circuit, and does not get destroyed after.

  • EARTHING -  the process of embedding the unwanted electrical  current into the ground/earth.

  • DOUBLE INSULATION - It is the process of protecting sensitive electrical components with 2 or more layers of insulative material. (e.g. rubber, wood, and plastic)

  • DC ( DIRECT CURRENT) - Current that flows in ONE DIRECTION

  • AC (ALTERNATING CURRENT) - current that CHANGES DIRECTION 



CONDUCTORS AND INSULATORS

  • CONDUCTORS - are materials used as passageways for electricity, and allow electrons to flow through. (e.g. copper, silver, aluminum, etc.)

  • INSULATORS - limit the flow of electricity and limit the flow of electrons (rubber, plastic, etc.)

VOLTAGE -

  • The main force of what drives electrons and currents through a circuit. It is what PUSHES the current throughout the circuit. It is also sometimes referred to as the “Electric Potential”

  • Unit: V (Volts)



CURRENT -

  • It is the rate at which the electrons and/or charge is flowing through the conductor. Imagine this being like the ELECTRICITY ITSELF. 

  • Unit: A (Amperes)



RESISTANCE - 

  • This is the “barrier” or what partially stops some of the current from passing through. This is like the wall that PUSHES BACK against it or RESISTS it.



  • Unit: Ω (Ohms)

EQUATIONS


(Kindly use this triangle as your guide hehe)



VOLTAGE - I * R (or current multiplied by resistance)



CURRENT - V/R (Voltage divided by Resistance) 



RESISTANCE - V/I (Voltage divided by Current) 

Series Circuit

  • It has only one road for electric current to flow.


Parallel Circuit

  • It has two or more paths for electric current to flow.   

  • Total Voltage = sum of the individual voltages 

  • Vₜ = V₁ + V₂ + V₃ …



  • The current is the same throughout the circuit

  • Iₜ = I₁ = I₂ = I₃ …



  • Total resistance =  total individual resistances


Example:

V1 = 2V

V2 = 4V

V3 = 6V

I = 2A 

(substitute) Vₜ = 2 + 4 + 6 = 12V

Rₜ = 12/2 = 6 Ω



  • To find the unknown R₃:

  • R₃ = Rₜ- (R₁ + R₂)

Example:

R1 = 4 Ω

R2 = 6 Ω

Rₜ = 15 Ω

R₃ = ?

(substitute) R₃ = 15 - (4 + 6)

R₃ = 15 - 10

R₃ = 5




  • Total Voltage:

  • Vₜ = V₁ = V₂ = V₃ …



  • Total current = sum of the individual branch currents

  • Iₜ = I₁ + I₂ + I₃ …



  • Total resistance:




Example:

R1 = 4 Ω 

R2 = 6 Ω

R3 = 12 Ω

Rₜ = ?

since they have different denominators, find the LCD which is 12



We multiply the top by the same number that we multiplied to the bottom to change the denominator to the LCD. So for ¼ (aka R1): we multiply 4 (denominator) by 3 to get 12 which is our LCD. So we also multiply 1 (numerator) by 3.



(if needed) simplify 6/12 (Rₜ) now flip it (½)



Rₜ = 2 Ω



  • To find the unknown R₃:


 Example:

R1 = 4 Ω 

R2 = 6 Ω

Rₜ = 2 Ω

R3 = ?

(substitute)

find the LCD which is 12

move 1/R3 to the left side to isolate it. 

flip the total (1/12)

R3 = 12 Ω


COMPONENTS OF AN ELECTRICAL CIRCUIT

  • Junction - a point in a circuit where two or more wires meet

Battery

  • It provides energy and voltage for charge to move. 


(don’t forget the positive and negative sign)

Wire

  • It lets electricity flow from one path to another. 



—————


Bulb

  • It glows when charge moves through it. 


Resistor

  • It slows down/limits the flow of electricity


Fuse

  • It is a safety device that protects an electrical circuit from excessive current. 




Open Switch


  • It is an open circuit which stops the flow of electricity. 

Closed Switch


  • It is a closed circuit which allows the electricity to flow freely.